FixVault
Home › Acura › 2010 › RDX 2.3 TB2 › Repair and Diagnosis › Transmission › Automatic Trans › Automatic Transmission › DTC Troubleshooting Index

DTC Troubleshooting Index

NOTE: Before you troubleshoot record all freeze data and any o n-board snapshot with the HDS, and review the GENERAL TROUBLESHOOTING INFORMATION .
DTC(1) Two Drive Cycle Detection D Indicator MIL Detection Item
P0107  (12) -- Blinks OFF or ON(3) Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage
P0108  (12) -- Blinks OFF or ON(3) Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage
P0335  (88) -- Blinks OFF or ON(3) Crankshaft Position (CKP) Sensor No Signal
P0339  (88) -- Blinks OFF or ON(3) Crankshaft Position (CKP) Sensor Circuit Intermittent Interruption
P0365  (89) -- Blinks OFF or ON(3) Camshaft Position (CMP) Sensor No Signal
P0369  (89) -- Blinks OFF or ON(3) Camshaft Position (CMP) Sensor Circuit Intermittent Interruption
P0705  (5)(2) -- Blinks ON Transmission Range Switch (Multiple Shift-Position Input)
P0706  (6)(2) ◦ OFF ON Transmission Range Switch (Open)
P0711  (28)(2) ◦ Blinks OFF ATF Temperature Sensor (Range/Performance)
P0712  (28)(2) ◦ Blinks OFF ATF Temperature Sensor (Short)
P0713  (28)(2) ◦ Blinks OFF ATF Temperature Sensor (Open)
P0714  (28)(2) ◦ Blinks OFF ATF Temperature Sensor Intermittent Failure
P0716  (15)(2) -- Blinks ON Input Shaft (Mainshaft) Speed Sensor (Range/Performance)
P0717  (15)(2) -- Blinks ON Input Shaft (Mainshaft) Speed Sensor (No Signal Input)
P0718  (15)(2) ◦ Blinks ON Input Shaft (Mainshaft) Speed Sensor (Intermittent Failure)
P0721  (9)(2) -- Blinks ON Output Shaft (Countershaft) Speed Sensor (Range/Performance)
P0722  (9)(2) -- Blinks ON Output Shaft (Countershaft) Speed Sensor (No Signal Input)
P0723  (9)(2) ◦ Blinks ON Output: Shaft (Countershaft) Speed Sensor (Intermittent Failure)
P0731  (64) ◦ Blinks OFF 1st Gear Incorrect Ratio
P0732  (64) ◦ Blinks OFF 2nd Gear Incorrect Ratio
P0733  (64) ◦ Blinks OFF 3rd Gear Incorrect Ratio
P0734  (64) ◦ Blinks OFF 4th Gear Incorrect Ratio
(1) The DTC in parentheses is the flash code the D indicator indicates when the data link connector (DLC) is connected to the HDS, and in the SCS mode.
(2) This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
(3) The MIL comes on when the PGM-FI system detects the same failure.
NOTE: Before you troubleshoot record all freeze data and any on-board snapshot with the HDS, and review the GENERAL TROUBLESHOOTING INFORMATION .
DTC(1) Two Drive Cycle Detection D Indicator MIL Detection Item
P0735  (64) ◦ Blinks OFF 5th Gear Incorrect Ratio
P0741  (40) ◦ Blinks OFF Torque Converter Clutch Circuit Performance or Stuck OFF
P0746  (76) ◦ Blinks ON A/T Clutch Pressure Control Solenoid Valve A Stuck OFF
P0747  (76) ◦ Blinks ON A/T Clutch Pressure Control Solenoid Valve A Stuck ON
P0751  (70) ◦ Blinks ON Shift Solenoid Valve A Stuck OFF
P0752  (70) ◦ Blinks ON Shift Solenoid Valve A Stuck ON
P0756  (71) ◦ Blinks ON Shift Solenoid Valve B Stuck OFF
P0757  (71) ◦ Blinks ON Shift Solenoid Valve B Stuck ON
P0761  (72) ◦ Blinks ON Shift Solenoid Valve C Stuck OFF
P0762  (72) ◦ Blinks ON Shift Solenoid Valve C Stuck ON
P0766  (73) ◦ Blinks ON Shift Solenoid Valve D Stuck OFF
P0767  (73) ◦ Blinks ON Shift Solenoid Valve D Stuck ON
P0776  (77) ◦ Blinks ON A/T Clutch Pressure Control Solenoid Valve B Stuck OFF
P0777  (77) ◦ Blinks ON A/T Clutch Pressure Control Solenoid Valve B Stuck ON
P0796  (78) ◦ Blinks ON A/T Clutch Pressure Control Solenoid Valve C Stuck OFF
P0797  (78) ◦ Blinks ON A/T Clutch Pressure Control Solenoid Valve C Stuck ON
P0812  (65)(2) ◦ Blinks ON Transmission Range Switch ATP R Switch
P0842  (25)(2) -- Blinks ON Transmission Fluid Pressure Switch A (2nd Clutch) Circuit Low
P0843  (25) -- Blinks ON Transmission Fluid Pressure Switch A (2nd Clutch) Circuit High
P0847  (26)(2) -- Blinks ON Transmission Fluid Pressure Switch B (3rd Clutch) Circuit Low
P0848  (26) -- Blinks ON Transmission Fluid Pressure Switch B (3rd Clutch) Circuit High
(1) The DTC in parentheses is the flash code the D indicator indicates when the data link connector (DLC) is connected to the HDS, and in the SCS mode.
(2) This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
NOTE: Before you troubleshoot record all freeze data and any on-board snapshot with the HDS, and review the GENERAL TROUBLESHOOTING INFORMATION .
DTC(1) Two Drive Cycle Detection D Indicator MIL Detection Item
P0872  (27)(2) -- Blinks OFF 4th Clutch Transmission Fluid Pressure Switch Circuit Low
P0873  (27) -- Blinks OFF 4th Clutch Transmission Fluid Pressure Switch Circuit High
P0962  (16)(2) -- Blinks ON A/T Clutch Pressure Control Solenoid Valve A (Open or Short)
P0963  (16)(2) -- Blinks ON A/T Clutch Pressure Control Solenoid Valve A
P0966  (23)(2) -- Blinks ON A/T Clutch Pressure Control Solenoid Valve B (Open or Short)
P0967  (23)(2) -- Blinks ON A/T Clutch Pressure Control Solenoid Valve B
P0970  (29)(2) -- Blinks ON A/T Clutch Pressure Control Solenoid Valve C (Open or Short)
P0971  (29)(2) -- Blinks ON A/T Clutch Pressure Control Solenoid Valve C
P0973  (7)(2) -- Blinks ON Shift Solenoid Valve A (Short)
P0974  (7)(2) -- Blinks ON Shift Solenoid Valve A (Open)
P0976  (8)(2) -- Blinks ON Shift Solenoid Valve B (Short)
P0977  (8)(2) -- Blinks ON Shift Solenoid Valve B (Open)
P0979  (22)(2) -- Blinks ON Shift Solenoid Valve C (Short)
P0980  (22)(2) -- Blinks ON Shift Solenoid Valve C (Open)
P0982  (60)(2) -- Blinks ON Shift Solenoid Valve D (Short)
P0983  (60)(2) -- Blinks ON Shift Solenoid Valve D (Open)
P16C0  (99) -- OFF ON PCM A/T Control System Incomplete Update
(1) The DTC in parentheses is the flash code the D indicator indicates when the data link connector (DLC) is connected to the HDS, and in the SCS mode.
(2) This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
NOTE: Before you troubleshoot record all freeze data and any on-board snapshot with the HDS, and review the GENERAL TROUBLESHOOTING INFORMATION .
DTC(1) Two Drive Cycle Detection D Indicator MIL Detection Item
P1717  (62)(2) -- Blinks ON Transmission Range Switch ATP RVS Switch (Open or Short)
P1743  (45) ◦ Blinks OFF Shift Valve E Stuck OFF
P1744  (45) ◦ Blinks OFF Shift Valve E Stuck ON
P1745  (45) ◦ Blinks OFF Servo Control Valve Stuck OFF or Servo Valve Stuck OFF
P1780  (49) ◦ Blinks ON Shift Control System (Transmission Default Mode)
P2122  (20) -- Blinks ON Accelerator Pedal Position (APP) Sensor A (Throttle Position Sensor D) Circuit Low Voltage
P2123  (20) -- Blinks ON Accelerator Pedal Position (APP) Sensor A (Throttle Position Sensor D) Circuit High Voltage
U0028  (107) -- Blinks OFF or ON(3) F-CAN Malfunction (PCM receiving failure)
U0122  (107) -- Blinks OFF F-CAN Malfunction (PCM - VSA Modulator-Control Unit)
U0155  (107) -- Blinks OFF or ON(3) F-CAN Malfunction (PCM - Gauge Control Module)
(1) The DTC in parentheses is the flash code the D indicator indicates when the data link connector (DLC) is connected to the HDS, and in the SCS mode.
(2) This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
(3) The MIL comes on when the PGM-FI system detects the same failure.
About FixVault