Readiness Code, Generating
WARNING: This page is about a different car, the 2009 Audi A8, 2008 Audi A8, 2007 Audi A8, 2006 Audi A8, and 2005 Audi A8. However, it is still accessible from the selected car via links, so may be relevant.
Requirements
- Fuses in fuse box (instrument panel, left) must be OK: → Electrical Wiring Diagrams, Troubleshooting and Component Locations
- Battery voltage (both batteries) must be at least 11.5 Volts.
- All electrical consumers such as, lights and rear window defroster must be switched off.
- For vehicles with automatic transmission, selector lever must be in "P".
- If vehicle is equipped with an air conditioning system, this must be switched off.
- The Ground (GND) connections between engine, transmission and body must be OK.
- There must not be any DTCs stored in DTC memory → Diagnostic Mode 03 - Read DTC Memory , Diagnostic mode 3: Check DTC memory.
- Intake air temperature 5 to 35 C → Diagnostic Mode 01 - Read Current System Data , Diagnostic mode 1: Check measured values; PID 15: Intake air temperature
- Fuses in right instrument panel fuse holder must be OK: → Electrical Wiring Diagrams, Troubleshooting and Component Locations
Right instrument panel fuse holder
Work Procedure
- Connect diagnostic tester → Diagnostic Tester, Connecting .
- Perform test drive. The following operating condition must be met during this road test:
- Coolant temperature must reach at least 80 C → Diagnostic Mode 01 - Read Current System Data , Diagnostic mode 1: Check measured values; PID 05, Coolant temperature.
Observe safety precautions that apply to road tests → Safety Precautions .
Let vehicle cool off with the ignition switched off until the following condition is met:
- Coolant temperature approx. intake air temperature (5 to 30 C) → Diagnostic Mode 01 - Read Current System Data , Diagnostic mode 1: Check measured values; PID 05, Coolant temperature.
- Perform a road test again. The following operating conditions must be met during this road test:
- Accelerate vehicle uniformly, not at Wide Open Throttle (WOT).
- Drive for 10 minutes in the highest gear or in the highest driving mode on a level driving surface at a constant speed in the range of 65 to 80 km/h at an engine speed of 2000 to 2500 RPM.
NOTE:
- Vehicle speed → Diagnostic Mode 01 - Read Current System Data , Diagnostic mode 1: Check measured values; PID 13, Vehicle speed.
- Engine speed → Diagnostic Mode 01 - Read Current System Data , Diagnostic mode 1: Check measured values; PID 12, Engine rotations per minute (RPM).
- After 10 minutes, downshift until an engine speed of 2800 to 3500 RPM has been reached.
- Drive in deceleration mode at a speed up to approx. 1800 RPM.
- Park vehicle and let engine run at idle for 3 minutes.
- Accelerator pedal must not be operated during this time.
- Perform a road test again. The following operating conditions must be met during this road test:
- Accelerate vehicle uniformly, not at Wide Open Throttle (WOT).
- Drive for 10 minutes in the highest gear or in the highest driving mode on a level driving surface at a constant speed in the range of 65 to 80 km/h at an engine speed of 2000 to 2500 RPM.
- Park vehicle and let engine run at idle for 3 minutes.
- Accelerator pedal must not be operated during this time.
- Read readiness code → Readiness Code, Reading .
If a 1 is displayed instead of a 0 in the 8-digit number block:
- Perform a road test again. The following operating conditions must be met during this road test:
- Drive for 10 minutes in the highest gear or in the highest driving mode on a level driving surface at a constant speed in the range of 65 to 80 km/h at an engine speed of 2000 to 2500 RPM.
- Park vehicle and let run at idle for 3 minutes.
- Accelerator pedal must not be operated during this time.
- Read readiness code → Readiness Code, Reading .
In 8-digit number block:
- Display position 5: Secondary air injection (AIR) system
And/or
- Display position 6: Evaporative emissions (EVAP) system
A 1 instead of 0 is displayed:
- Repeat work procedure completely.