Section 19 (Engine Electrical System - Repair -- F32)
WARNING: This page is about a different variant/trim than selected.
- Troubleshooting
- 61 20... Battery replacement information
- 61 13... Butt connector for repairing a plug connection
- 12 00 Contents of Engine Electrical System General
- 11 00... Handling components after flood damage
- 12 00... Instructions for removal and replacement of control units
- 12 00... Instructions for working on the ignition system
- 61 00... Notes for disconnecting and connecting battery
- 61 13... Notes for opening contacts and locks of different plug contact systems
- 61 00... Notes on handling wiring harnesses and cables
- 12 00... Instructions for welding work (overload protection of control units)
- 12 00... Instructions for connecting and disconnecting test units
- 12 00... Instructions on component testing
- 12 00... Notes/information on start assistance (jump starting)
- 00 Safety information for working on vehicles with automatic engine start-stop function (MSA)
- Ignition Wires, Spark Plugs
- Ignition Coil
- Electronic Switching Or Control Units
- 12 14 700 Coding control module (DME/DDE)
- 12 14 705 Programming control unit (DME/DDE)
- 12 14 602 Removing/replacing knock sensor (1st and 2nd cylinder) (N20, N26)
- 12 14 600 Removing/replacing knock sensor (3rd and 4th cylinder) (N20, N26)
- 12 14 600 Removing/replacing knock sensors (N55)
- 12 14 524 Replace pulse sensor on exhaust camshaft (N20, N26)
- 12 14 550 Replacing control unit (DME) (N20, N26)
- 12 14 550 Replacing control unit (DME) (N55)
- 12 14 521 Replacing crankshaft pulse sensor (N20, N26)
- 12 14 521 Replacing crankshaft pulse sensor (N55)
- 12 63 586 Replacing power distribution module (N20, N26, N55)
- 12 14 651 Replacing pressure sensor on charge air duct (N55)
- 12 14 650 Replacing pressure sensor on intake plenum (N55)
- 12 14 524 Replacing pulse sensor on exhaust camshaft (N55)
- 12 14 523 Replacing pulse sensor on intake camshaft (N20, N26)
- 12 14 523 Replacing pulse sensor on intake camshaft (N55)
- 12 14 650 Replacing suction pressure sensor on intake plenum (N20, N26)
- 12 14 650 Replacing suction pressure sensor on pressure pipe (N20, N26)
- Alternator With Drive And Mounting
- Controller
- Starter With Mounting
- Starter Lead
- 12 42 500 Replacing positive battery cable between starter motor, alternator and positive battery connection point (N55)
- 12 42 540 Replacing safety battery terminal (SBK)
- 12 42 500 Replacing the positive battery cable between the starter motor, alternator and positive battery connection point (N20, N26)
- Engine Wiring Loom
- 12 51 235 Removing and installing/replacing engine sensor system wiring harness module 1 (N20, N26)
- 12 51 240 Removing and installing/replacing engine wiring harness sensor system module 2 (N20, N26)
- 12 51 215 Replacing wiring harness section for Valvetronic servomotor (N20, N26)
- 12 51 001 Replacing wiring harness section for engine (N55)
- 12 51 245 Replacing wiring harness section for engine transmission module (N20, N26)
- 12 51 210 Replacing wiring harness section for ignition and injectors (N20, N26)
- 12 51 100 Replacing wiring harness section for ignition and injectors (N55)
- Oil Pressure/Oil Temperature/Oil Gauge
- 12 61 285 Removing and installing/renewing oil level sensor for engine oil (N55)
- 12 61 588 Removing and installing/replacing engine oil pressure/temperature sensor (N20, N26)
- 12 61 285 Removing and installing/replacing oil level sensor for engine oil (N20, N26)
- 12 61 280 Removing and installing/replacing oil pressure sensor (N55)
- Switches And Relays