Section 1256 (General Orphan Data)
WARNING: This page does not describe the selected car, but rather 11 other vehicles, including the 2019 BMW 340i GT xDrive, 2019 BMW 330i xDrive, 2019 BMW 330i GT xDrive, 2018 BMW 340i GT xDrive, and 2018 BMW 330i xDrive. However, it is still accessible from the selected car via links, so may be relevant.
- Adjusting the eccentric shaft to minimum lift
- Block the crankshaft in the TDC firing position of cylinder 1 (manual transmission)
- Blocking the camshafts
- Blocking the crankshaft in the TDC firing position of the first cylinder (automatic transmission)
- Bring front compartment lid in the service position
- Carry out the following follow-up work
- Carrying out vehicle test
- Check engine oil level
- Checking the position of the intake camshaft (cylinder head removed)
- Checking the position of the intake camshaft at cylinders 3 and 4 (cylinder head removed)
- Checking/Adding the transmission oil level (GA8HP45Z, GA8HP50Z, GA8HP70Z, GA8HP75Z, GAHP90Z)
- Connect the charge air line to the exhaust turbocharger
- Connect the coolant line to the high-temperature coolant circuit
- Connecting connector A46*6B to the control unit
- Connecting the battery earth lead
- Connecting the connector with the DME control unit and the power distribution box (PDM)
- Connecting the coolant feeder hose to the connecting bracket
- Connecting the diagnostic system for possible integration level encoding and programming
- Crank engine twice (automatic transmission)
- Crank the engine twice (manual transmission)
- Delete fault memory
- Detach oil supply line from the engine block
- Detach the propeller shaft from the transmission and tie it up on the vehicle floor
- Detaching the charge air line from the throttle body
- Detaching the gearshift lever cover
- Disassembling all special tools
- Disassembling the special tool 2 358 122
- Disconnect the charge air line from the exhaust turbocharger
- (Disconnecting the battery earth lead)
- Disconnecting the connector A46*6B from the control unit
- Disconnecting the connector from the DME control unit and from the power distribution box (PDM)
- Drain the engine oil (remove the full-flow oil filter)
- Tightening the oil filter cover
- Evacuating the air conditioning
- Fasten charge air line to the throttle body
- Filling the air conditioning
- For replacement: Reset adaptation values
- If the DME control unit is replaced
- Install acoustic cover at front
- Uninstalling the cover for the DME control unit
- Install cover for the DME control unit
- Install front panel, center
- Install right engine support arm
- Install right luggage compartment trim panel
- Install the connecting support with the tension strut
- Install the connecting support
- Install the coolant feed line (coolant return line is removed)
- Install the front section of the right wheel arch cover
- Install the protective plate for the fuel lines
- Install the tension strut (rear end)
- Install the unfiltered-air snorkel
- Install transmission cross member
- (Install transmission)
- Install valve springs
- Installing air conditioning compressor
- Installing all spark plugs
- Installing Lambda oxygen sensor
- Installing switch trim on the front left or right front door trim panel
- Installing the complete exhaust system
- Installing the design cover
- Installing the engine on the assembly jig
- Installing the front right wheel
- Installing the gearshift lever cover
- Installing the heat shield
- Installing the ignition coils
- Installing the luggage compartment floor trim panel
- Installing the magnet wheel
- Installing the oil deflector
- Installing the oil filter element
- Partially installing the propeller shaft
- Partially release propeller shaft
- Remove complete exhaust system
- Remove the heat shield
- Removing the luggage compartment floor trim panel
- Top up the transfer box oil (Active Torque Control 35L)
- Installing the outer cover on the front seat
- Remove acoustic cover at front
- Remove design cover
- Installing the oxygen sensor monitor
- Installing the partition wall attachment part
- Installing the right engine bulkhead
- Installing valve stem seals
- (Lower/raise front axle support)
- Lowering the engine and detaching the engine bridge
- Mount the front left and right wheels
- Mount the sound insulation in the front
- Mounting the propeller shaft and center mount
- Mounting the wheel
- Partially detach the sound insulation in front
- Partially remove the front seat
- Perform the following preliminary work
- Prepare the assembly jig
- Install front seat (partially removed)
- Releasing the coolant feeder hose from the connecting bracket
- Releasing the oil drain plug
- Releasing the oil filter cover
- Releasing the steering shaft on the electromechanical steering gear
- Remove air conditioning compressor
- Remove/install bearing support (lowering/raising front axle support)
- Remove engine mount from the engine
- (Remove/install front axle differential)
- Remove front panel, center
- Remove front right wheel
- Remove front section of the right wheel arch cover
- Remove fuel delivery line
- (Remove transmission)
- Remove ignition coils
- Remove outer cover on front seat
- Remove right engine support arm
- Remove right luggage compartment trim panel
- Remove the chain tensioner (engine removed)
- Remove the connecting support with the tension strut
- Remove the connecting support
- Remove the coolant feed line (coolant return line is removed)
- Remove the front left and right wheels
- Remove the protective plate for the fuel lines
- Remove the tension strut (rear end)
- Remove the unfiltered-air snorkel
- Remove trailing link at spring strut dome
- Remove transmission cross-member
- Remove valve stem seals
- Removing all spark plugs
- Removing the engine from the assembly jig
- Removing the lambda oxygen sensor
- Removing the magnet wheel
- Removing the oil deflector
- Removing the oil filter element
- Removing the oxygen sensor monitor
- Removing the right engine bulkhead
- Removing the wheel
- Removing valve springs
- Replacement: Operate the gasoline particulate filter for the first time
- Secure the engine mount on the engine
- Securing the oil feed line to the engine block
- Securing the steering shaft on the electromechanical steering gear
- Take hood out of the service position
- Tightening the oil drain plug
- Tightening the oil filter cap
- Topping up the motor oil
- Turning the engine on the vibration damper
- Version with eccentric shaft servomotor: Teaching in the end stops with the diagnostic system
- When replacing the gasoline particulate filter: Register the gasoline particulate filter
- Installing fuel delivery line