General Orphan Data (2 Of 2)

(Recoding of spare parts (housings and contacts) from "Repair set 4 for vehicle electrical system" All)
(New universal crimping die (all))
(New crimping pliers and interchangeable dies (all))
(Wiring harness repair kit 4.0 (61 13 4 470 939) and associated special tools)
(Register battery change)
(Charging parameters for lithium ion batteries)
(Removing airbag unit (M Sport steering wheel))
(Installing the airbag unit (M Sport steering wheel))
(Encode/program control unit(s))
(Removing trim panels on the operating facility in the center console)
(Installing the trims on the operating facility in the center console)
(New main number for the antistatic mat)
(Initializing rain, light and solar sensor)
(Initialize component protection)
(Dynamic marker light)
(Processing the LED headlight service test module)
(Sealing all ventilation elements on the headlight)
(Preparing the headlight internal pressure test)
(Remove butyl on the headlight)
(Fitting ventilation elements on the headlight)
(Adjust the LED module for the light carpet)
(Enter the installation position of the damper motor)
(Fill and vent the coolant circuit)
(Removing the left air duct for the footwell)
(Installing the left-hand air duct for the footwell)
(Addressing the controller drive)
(R134a Air-conditioning system servicing device Beissbarth A/Ccellence 2500)
(Draw off and dispose of contaminated refrigerant R1234yf)
(Releasing the intake pipe from the connecting piece)
(Releasing the coolant expansion tank of high-temperature coolant circuit)
(Attaching the intake pipe on the air conditioning compressor)
(Fastening the coolant expansion tank of high-temperature coolant circuit)
(Attach the control unit holder)
(Releasing the inner panel for the luggage compartment partition wall)
(Attaching the inner panel for the luggage compartment partition wall)
(Removing the holder of storage tray in the cargo area)
(Install the holder of storage tray in the luggage compartment)
(Installing the correct navigation map)
(Importing the Service history)
(Adjust the sensors for the driving dynamics)
(Partially removing the front right wheel arch cover)
(Partially installing the front right wheel arch cover)
(Removing the reinforcement on the right front bumper cover)
(Removing the trim strip on the right front bumper cover)
(Installing the trim strip on the right front bumper cover)
(Installing reinforcement of front right bumper cover)
(Partially installing the front wheel arch cover)
(Checking the installation position of the drive for the exterior mirror adjustment)
(Removing the rear side trim panel holder)
(Installing the rear side trim panel holder)
(Carrying out a system check of the telematics control module emergency battery)
(Attach the engine from the automatic transmission (lifting table))
(Installing starter motor)
(Removing the complete front axle with the engine and transmission)
(Removing the engine from the front axle)
(Installing the engine on the assembly jig)
(Releasing the oil drain plug)
(Tightening the oil drain plug)
(Blocking engine in TDC firing position)
(Removing the oil deflector)
(Mounting the short block on the assembly jig)
(Installing the oil deflector)
(Removing the engine from the assembly jig)
(Mounting the engine on the front axle)
(Installing the complete front axle with the engine and transmission)
(Remove the left and right front-end strut)
(Installing front-end strut on left and right)
(Remove clean air pipe)
(Removing rear left torsion strut)
(Install the rear left torsion strut)
(Install clean air pipe)
(Partially releasing the holder of the positive battery cable)
(Attaching the bracket of the positive battery cable)
(Removing underbody planking on left and right side)
(Installing the torsion strut left and right)
(Releasing the left and right tie rod ends from the swivel bearing)
(Releasing the control arm below on the left and right from the swivel bearing)
(Mount the wishbone at the bottom left and right on the swivel bearing)
(Attaching the left and right tie rod end on the swivel bearing)
(Remove underbody protection at side right and left)
(Measuring the ride height of the front axle and adjusting the normal position)
(Tightening the screw connection for the tension strut on the front subframe on the left and right)
(Removing crash levers left and right)
(Installing the left and right crash lever)
(Securing the crankcase with the engine bridge)
(Removing the oil deflector (engine installed))
(Installing the oil deflector (engine installed))
(Releasing the engine bridge from the crankcase)
(Adjusting the eccentric shaft to minimum lift)
(Check the position of the intake camshaft at cylinder 3 and 4)
(Checking the position of the intake camshaft)
(Remove torsion springs)
(Installing torsion springs)
(Deactivate vehicle electrical system)
(Installing thrust field on the shock tower)
(Checking installation position of roller cam followers (sDrive30i))
(Checking installation position of roller cam followers (M40i))
(Check engine oil level)
(Partially removing the charge air line)
(Partially installing the charge air line)
(For electrical wastegate valve controller: teaching in and checking end stops with the diagnostic system (after vehicle diagnosis))
(Lowering exhaust system)
(Fastening the exhaust system)
(Remove front right wheel)
(Removing the right hand front bottom side cover)
(Remove the front right wheel arch cover front section)
(Install the front section of the front right wheel arch cover)
(Install the bottom front right side cover)
(Installing the front right wheel)
(Attaching the front left wheel)
(Remove front left or right wheel)
(Install front left or right wheel)
(Partially remove the mount of the hood seal)
(Partially installing the mount for the hood seal)
(Partially removing the radiator of high-temperature coolant circuit)
(Partially installing the radiator for the high-temperature coolant circuit)
(Check engine mount)
(When replacing the gasoline particulate filter: Register the gasoline particulate filter)
(Removing all ignition coils)
(When replacing (control unit): Performing service function "self-locking differential control unit replacement")
(Installing all ignition coils)
(Repair techniques, repair stage 2)
(Release the control unit holder)
(Releasing air conditioning compressor)
(Fasten air conditioning compressor)
(Partially removing the air conditioning compressor)
(Installing the air conditioning compressor (partially installed))
(Removing starter motor)
(Removing the engine from the automatic transmission (lifting table))
(Install the right front-end strut)
(Remove right front-end strut)
(Installing the left and right vanity mirror light)
(Removing the vanity mirror light at the front left and right)
(Install A-pillar trim panel, left and right)
(Remove A-pillar trim panel, left and right)
(Removing the air duct for the footwell)
(Installing the right-hand air duct for the footwell)
(Installing the front section of the front wheel arch cover on the left and right)
(Removing left and right brake ventilation duct)
(Install air duct in footwell)
(Removing the air duct in the footwell)
(Removing the support for the switch combination for adjusting the seat)
(Installing the support for seat adjustment switch combination)