Specifications Index

LACROSSE SPECIFICATIONS INDEX

System		Specification/Procedure
Air Conditioning
Service		REFRIGERANT SYSTEM CAPACITIES
Torque		FASTENER TIGHTENING SPECIFICATIONS
Front & Rear Wheel Drive Shaft Nut
First Pass		(New Nut) 111 ft. lbs. (150 N.m)
	Second Pass	Back Nut Off 45 degrees
	Third Pass	184 lb ft (250 N.m)
Battery		BATTERY USAGE
Brakes
Bleeding Sequence		RR, LF, LR, RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL)
Disc Brakes
	Service Specifications	DISC BRAKE COMPONENT SPECIFICATIONS
	Torque	FASTENER TIGHTENING SPECIFICATIONS
Charging
Generator		GENERATOR USAGE
Torque		FASTENER TIGHTENING SPECIFICATIONS
Drive Belts
Adjustment		Serpentine drive belts are not adjustable
Drive Belt Routing		For 2.4L, See illustration under DRIVE BELT REPLACEMENT For 3.0L & 3.6L, See illustration under DRIVE BELT REPLACEMENT
Engine Cooling
General Service Specifications		SPECIFICATIONS
	Radiator Cap Pressure	Specification is stamped on pressure cap
	Thermostat R & I
	2.4L	ENGINE COOLANT THERMOSTAT REPLACEMENT (L4)
	3.0L & 3.6L	ENGINE COOLANT THERMOSTAT REPLACEMENT (V6)
	Water Pump R & I
	2.4L	WATER PUMP REPLACEMENT (L4)
	3.0L & 3.6L	WATER PUMP REPLACEMENT (V6)
Engine Mechanical
2.4L
	Compression	No cylinder reading should be less than 100 psi (690 kPa). The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST
	Oil Pressure	Oil Pressure - @ 1,000 RPM 30-70 psi (2.6.84-482.63 kPa) at 90°C (194°F)
	Overhaul	ENGINE MECHANICAL SPECIFICATIONS
	Torque	FASTENER TIGHTENING SPECIFICATIONS
3.0L & 3.6L
	Compression	No cylinder reading should be less than 140 psi (965 kPa). The lowest reading should not be less than 70 percent of the highest reading. ENGINE COMPRESSION TEST
	Oil pressure	10 psi (69 kPa) at Idle 20 psi (138 kPa) at 2,000 engine RPM
Overhaul		ENGINE MECHANICAL SPECIFICATIONS (LF1) ENGINE MECHANICAL SPECIFICATIONS (LLT)
	Torque	FASTENER TIGHTENING SPECIFICATIONS
Fluid Specifications		See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive PlateTorque
2.4L		First Pass 39 ft. lbs. (53 N.m) Last Pass + an additional 25 degrees
	3.0L & 3.6L	First Pass 22 ft. lbs. (30 N.m) Last Pass + an additional 45 degrees
Fuel System
Pressure Specification		2.4L 40-84 psi (276-580 kPa) 3.0L & 3.6L 40-65 psi (276-448 kPa)
	Fuel Pressure Test Procedure	2.4L See FUEL SYSTEM DIAGNOSIS 3.0L & 3.6L See FUEL SYSTEM DIAGNOSIS and
	Fuel Filter Location	2.4L fuel filter is a component of fuel tank fuel pump module in fuel tank and is not serviceable 3.0L & 3.6L fuel filter is located in primary fuel tank module, fuel strainer attaches to lower end of primary fuel tank module
	Fuel Filter R & I	2.4L See FUEL TANK FUEL PUMP MODULE REPLACEMENT (NT7) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (NU6) 3.0L & 3.6L See FUEL TANK FUEL PUMP MODULE REPLACEMENT (NT7) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (NU6)
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)		2.4L Individual Ignition Coil/Module Assemblies V6 NA
Ignition Wires (Routing)		NA
Spark Plug
2.4L
	Gap	0.035 in (1.0 mm)
	Torque	15 lb ft (20 N.m)
3.0L & 3.6L
	Gap	0.043 in (1.1 mm)
	Torque	15 lb ft (20 N.m)
Starting
Starter		STARTING SYSTEM DESCRIPTION AND OPERATION
Torque		FASTENER TIGHTENING SPECIFICATIONS
Wheel Alignment
	Adjustment Specifications	WHEEL ALIGNMENT SPECIFICATIONS
	Torque	FASTENER TIGHTENING SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque (See Tightening Pattern under wheel and tire INSTALLATION PROCEDURE		111 lb ft (150 N.m)