FixVault
Home › Buick › 2017 › Encore Base › Repair and Diagnosis › External Pages › Different variant/trim › Section 5 (Engine Mechanical - 1.4L (LE2)) › Specifications › Engine Mechanical Specifications

Engine Mechanical Specifications

WARNING: This page is about a different variant/trim than selected.
Application Specification
Metric English
General Data
  • Engine Type
 4-Cylinder Inline
  • Displacement
 1.4L 85 CID
  • RPO
 LE2, LEX, LFE
  • Valves
 16
  • Bore
 74 mm 2.91 in
  • Stroke
 81.3 mm 3.200 in
  • Compression Ratio
 10.0:1
  • Spark Plug Gap
 0.60-0.70 mm 0.024-0.028 in
  • Firing Order
 1-3-4-2
Block
  • Crankshaft Main Bearing Bore Diameter
 51.868-51.882 2.0420-2.0426 in
  • Cylinder Bore Diameter
 73.992-74.008 mm 2.913-2.914 in
  • Cylinder Bore Out-of-Round - Maximum
 0.013 mm 0.0005 in
  • Cylinder Head Deck Surface Flatness - over 25 mm length
 0.025 mm 0.0010 in
  • Cylinder Head Deck Surface Flatness - over 150 mm length
 0.050 mm 0.0020 in
Engine Block to Bedplate Flatness - overall 0.1 mm 0.004 in
Engine Block to Bedplate Flatness - straightness 0.050-0.100 mm 0.0020-0.0040 in
Piston Deck Height - Below Deck 0.74-0.94 mm 0.029-0.037 in
Camshaft
  • Camshaft End Play
 0.040-0.660 mm 0.0016-0.0260 in
  • Camshaft Journal Clearance
 0.040-0.085 mm 0.0016-0.0033 in
  • Camshaft Journal Diameter - Journal 1
 30.935-30.960 mm 1.2179-1.2189 in
  • Camshaft Journal Diameter - Journal 2-6
 23.935-23.960 mm 0.9423-0.9433 in
  • Camshaft Thrust Width - Camshaft with Phaser installed
 33.175-33.525 mm 1.3061-1.3199 in
  • Camshaft Thrust Width - Cylinder Head
 32.865-33.135 mm 1.2939-1.3045 in
Connecting Rod
  • Connecting Rod Bearing to Crankpin Clearance
 0.013-0.068 mm 0.0005-0.0027 in
  • Connecting Rod Bore Diameter - Bearing End
 47.186-47.202 mm 1.8577-1.8583 in
  • Connecting Rod Bore Diameter - Pin End w/Bushing
 18.007-18.017 mm 0.7089-0.7093 in
  • Connecting Rod Side Clearance
 0.090-0.350 mm 0.0035-0.0138 in
  • Connecting Rod Straightness - Bend - Maximum
 0.017 mm 0.0007 in
  • Connecting Rod Straightness - Twist - Maximum
 0.040 mm 0.0016 in
Crankshaft
  • Connecting Rod Journal Diameter
 43.992-44.008 mm 1.7320-1.7326 in
  • Connecting Rod Journal Out-of-Round
 0.005 mm 0.0002 in
  • Crankshaft End Play
 0.15-0.38 0.0059-0.0150 in
  • Crankshaft Main Bearing Clearance #1 Bearing
 0.011-0.070 0.0004-0.0028
  • Crankshaft Main Bearing Clearance # 2, 3, 4 and 5 Bearings
 0.012-0.067 0.0005-0.0026
  • Crankshaft Main Journal Diameter
 46.992-47.008 1.8501-1.8507 in
  • Crankshaft Main Journal Out-of-Round
 0.005 mm 0.0002 in
Cylinder Head
  • Surface Flatness - Block Deck - in 25 mm
 0.025 mm 0.0010 in
  • Surface Flatness - Block Deck - in 150 mm
 0.050 mm 0.0020 in
  • Surface Flatness - Block Deck - between bolts
 0.030 mm 0.0012 in
  • Surface Flatness - Block Deck - Overall
 0.100 mm 0.0039 in
  • Valve Guide Bore - Exhaust
 5.000-5.020 mm 0.1968-0.1976 in
  • Valve Guide Bore - Intake
 5.000-5.020 mm 0.1968-0.1976 in
  • Valve Lifter Bore Diameter - Stationary Lash Adjusters
 12.008-12.030 mm 0.4728-0.4736 in
  • Valve Seat Angle - Relief Surface
 50 Degrees
  • Valve Seat Angle - Seating Surface
 90 Degrees
  • Valve Seat Angle - Undercut Surface
 120 Degrees
  • Valve Seat Runout - Maximum
 0.080 mm 0.0031 in
Lubrication System
  • Oil Pressure - @ 1500 RPM 100°C
 200-250 kPa 29-36 psi
Piston Rings
  • Piston Ring End Gap - Top
 0.25-0.40 mm 0.010-0.016 in
  • Piston Ring End Gap - Second
 0.40-0.60 mm 0.016-0.024 in
  • Piston Ring End Gap - Oil Control
 0.25-0.75 mm 0.010-0.030 in
  • Piston Ring to Groove Clearance - Top
 0.03-0.08 mm 0.001-0.003 in
  • Piston Ring to Groove Clearance - Second
 0.03-0.07 mm 0.001-0.003 in
  • Piston Ring to Groove Clearance - Oil Control
 0.050 -0.190 mm 0.0020-0.0075 in
  • Piston Ring Thickness - Top
 1.17-1.19 mm 0.046-0.047 in
  • Piston Ring Thickness - Second
 1.17-1.19 mm 0.046-0.047 in
  • Piston Ring Thickness - Oil Control - Rail
 0.045-0.47 mm 0.0018-0.0019 in
  • Piston Ring Thickness - Oil Control - Spacer
 1.67-1.79 mm 0.066-0.071 in
Pistons and Pins
  • Pin - Piston Pin Clearance to Connecting Rod Bore
 0.007-0.020 mm 0.0003-0.0008 in
  • Pin - Piston Pin Clearance to Piston Pin Bore
 0.002-0.010 mm 0.0001-0.0004 in
  • Pin - Piston Pin Diameter
 17.997-18.000 mm 0.7085-0.7087 in
  • Pin - Piston Pin End Play
 0.18-0.79 mm 0.0071-0.0311 in
  • Piston - Piston Diameter - @ 38 mm up from crown
 73.957-73.971 mm 2.9117-2.9122 in
  • Piston - Piston Pin Bore Diameter
 18.002-18.010 mm 0.7087-0.7091 in
  • Piston - Piston Ring Groove Width - Top
 1.23-1.25 mm 0.0484-0.0492 in
  • Piston - Piston Ring Groove Width - Second
 1.23-1.25 mm 0.0484-0.0492 in
  • Piston - Piston Ring Groove Width - Oil Control
 2.03-2.05 mm 0.0799-0.0807 in
  • Piston - Piston to Bore Clearance - w/Polymer
 -0.017 mm to +0.029 mm -0.0007 in to +0.0011 in
Valve System
  • Valves - Valve Face Angle
 90 Degrees
  • Valves - Valve Face Runout - Maximum
 0.050 mm 0.0020 in
  • Valves - Valve Seat Runout - Maximum
 0.080 mm 0.0031 in
  • Valves - Valve Seat Gauge Ball Height - Exhaust
 8.85-9.09 mm 0.3484-0.3579 in
  • Valves - Valve Seat Gauge Ball Height - Intake
 9.47-9.71 mm 0.3728-0.3823 in
  • Valves - Valve Stem Diameter - Exhaust
 4.945-4.965 mm 0.1947-0.1955 in
  • Valves - Valve Stem Diameter - Intake
 4.955-4.975 mm 0.1951-0.1959 in
  • Valves - Valve Stem Installed Height
 Check and Record
  • Valves - Valve Stem to Guide Clearance - Exhaust
 0.035-0.075 mm 0.0014-0.0030 in
  • Valves - Valve Stem to Guide Clearance - Intake
 0.025-0.065 mm 0.0010-0.0026 in
  • Valve Lash Adjusters - Valve Lash Adjuster Diameter - Stationary Lash Adjuster
 11.986-12.000 mm 0.4719-0.4724 in
  • Valve Lash Adjusters - Valve Lash-Adjuster-to-Bore Clearance - Stationary Lash Adjuster
 0.008-0.044 mm 0.0003-0.0017 in
  • Valve Springs - Valve Spring Installed Height
 34.50-35.50 mm 1.358-1.398 in
  • Valve Springs - Valve Spring Load - Closed - @ 35 mm
 225-245 N 51-55 lb
  • Valve Springs - Valve Spring Load - Open - @ 26.5 mm
 405-445 N 91-100 lb
About FixVault