Fastener Specifications
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| Camshaft Cover Gasket |
| Connecting Rod Bearing |
| Crankshaft Front Oil Seal |
| Crankshaft Rear Oil Seal |
| Cylinder Head Gasket |
| Cylinder Head Oil Gallery Plug |
| Engine Coolant Thermostat Housing Gasket |
| Exhaust Manifold Gasket |
| Fuel Injection Fuel Rail Seal |
| Fuel Injector Nozzle Housing Seal |
| Fuel Injector Seal Spacer |
| Fuel Pump Gasket |
| Fuel Pump Housing Seal |
| Intake Manifold Gasket |
| Oil Pan Gasket |
| Piston Pin Retainer |
| Thermostat Bypass Pipe Gasket |
| Throttle Body Gasket |
| Timing Chain Tensioner Seal |
| Vacuum Pump Gasket |
| Vacuum Pump Seal |
| Valve Stem Oil Seal |
| Water Outlet Gasket |
| Water Pump Gasket |
Single Use Threaded Fastener/Component Tightening Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Automatic Transmission Flex Plate Bolt | |
|
30 N.m (22 lb ft) |
|
40 degrees |
| Balance Shaft Sprocket Bolt | |
|
40 N.m (30 lb ft) |
|
50 degrees |
| Camshaft Position Actuator Bolt | |
|
30 N.m (22 lb ft) |
|
100 degrees |
| Connecting Rod Bolt | |
|
25 N.m (18 lb ft) |
|
110 degrees |
| Crankshaft Balancer Bolt | |
|
150 N.m (111 lb ft) |
|
140 degrees |
| Cylinder Head Bolt | |
|
30 N.m (22 lb ft) |
|
190 degrees |
| Cylinder Head Core Hole Plug | 50 N.m (37 lb ft) |
| Engine Front Cover Bolt - M10 | 58 N.m (43 lb ft) |
| Engine Front Cover Bolt - M10 [3x] | |
|
15 N.m (11 lb ft) |
|
130 degrees |
| Exhaust Manifold Bolt | 20 N.m (15 lb ft) |
| Fuel Feed Intermediate Pipe | |
|
15 N.m (11 lb ft) |
|
30 N.m (22 lb ft) |
| Fuel Pump Bolt | |
|
8 N.m (71 lb in) |
|
50 degrees |
| Lower Crankcase Bolt - M10 | |
|
20 N.m (15 lb ft) |
|
140 degrees |
| Oil Filter | 3/4 to 1 full turn after gasket makes contact with the sealing surface on the filter mounting flange |
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Balance Chain Guide Bolt | 10 N.m (89 lb in) |
| Balancer Chain Tensioner Bolt | 10 N.m (89 lb in) |
| Balancer Shaft with Oil Pump Bolt | |
|
58 N.m (43 lb ft) |
|
58 N.m (43 lb ft) |
| Belt Idler Pulley Bolt | 22 N.m (16 lb ft) |
| Belt Idler Pulley Bracket Bolt | 22 N.m (16 lb ft) |
| Camshaft Bearing Cap Bolt | 10 N.m (89 lb in) |
| Camshaft Bearing Cap Bolt- Front | 10 N.m (89 lb in) |
| Camshaft Cover Bolt | 10 N.m (89 lb in) |
| Camshaft Cover Heat Shield Bolt | 10 N.m (89 lb in) |
| Camshaft Cover Opening Plug | 35 N.m (26 lb ft) |
| Camshaft Cover Stud | 10 N.m (89 lb in) |
| Camshaft Position Actuator Solenoid Valve Bolt | 10 N.m (89 lb in) |
| Camshaft Position Sensor Bolt | 10 N.m (89 lb in) |
| Crankshaft Position Sensor Bolt | 10 N.m (89 lb in) |
| Cylinder Head Oil Gallery Plug | 40 N.m (30 lb ft) |
| Engine Block Oil Gallery Plug | 65 N.m (48 lb ft) |
| Engine Block Oil Gallery Plug | 40 N.m (30 lb ft) |
| Engine Coolant Air Bleed Pipe Bolt | 10 N.m (89 lb in) |
| Engine Coolant Heater | 50 N.m (37 lb ft) |
| Engine Coolant Heater Hole Plug | 60 N.m (44 lb ft) |
| Engine Coolant Thermostat Housing Bolt | 10 N.m (89 lb in) |
| Engine Front Cover Bolt - M6 | 10 N.m (89 lb in) |
| Engine Front Cover Bolt - M8 | 25 N.m (18 lb ft) |
| Engine Lift Front Bracket Bolt | 25 N.m (18 lb ft) |
| Engine Lift Rear Bracket Bolt | 25 N.m (18 lb ft) |
| Engine Oil Level Indicator Switch Bolt | 10 N.m (89 lb in) |
| Engine Oil Pressure Sensor | 35 N.m (26 lb ft) |
| Exhaust Manifold Heat Shield Bolt | 14 N.m (124 lb in) |
| Fuel Injection Fuel Rail Bolt | 25 N.m (18 lb ft) |
| Fuel Injection Fuel Rail Fuel Pressure Sensor | 33 N.m (24 lb ft) |
| Fuel Pump Shield Bolt | 10 N.m (89 lb in) |
| Ignition Coil Bolt | 10 N.m (89 lb in) |
| Intake Manifold Bolt | 12 N.m (106 lb in) |
| Intake Manifold Cover Bolt | 9 N.m (80 lb in) |
| Knock Sensor Bolt | 25 N.m (18 lb ft) |
| Lower Crankcase Bolt - M8 | 25 N.m (18 lb ft) |
| Lower Oil Pan Bolt | 10 N.m (89 lb in) |
| Manifold Absolute Pressure Sensor Bolt | 5 N.m (44 lb in) |
| Oil Filter Fitting | 50 N.m (37 lb ft) |
| Oil Pan Baffle Bolt | 10 N.m (89 lb in) |
| Oil Pan Bolt - M6 | 10 N.m (89 lb in) |
| Oil Pan Bolt - M8 | 25 N.m (18 lb ft) |
| Oil Pan Drain Plug | 25 N.m (18 lb ft) |
| Oil Pump Flow Control Valve Bolt | 10 N.m (89 lb in) |
| Oxygen Sensor | 42 N.m (31 lb ft) |
| Piston Oil Nozzle Bolt | 10 N.m (89 lb in) |
| Positive Crankcase Ventilation Valve Bolt | 10 N.m (89 lb in) |
| Thermostat Bypass Pipe Bolt | 10 N.m (89 lb in) |
| Throttle Body Bolt | 10 N.m (89 lb in) |
| Timing Chain Guide Bolt | 25 N.m (18 lb ft) |
| Timing Chain Tensioner Bolt | 25 N.m (18 lb ft) |
| Timing Chain Tensioner Shoe Bolt | 25 N.m (18 lb ft) |
| Vacuum Pump Bolt | 10 N.m (89 lb in) |
| Water Outlet Bolt | 12 N.m (106 lb in) |
| Water Pump Bolt | 25 N.m (18 lb ft) |