FixVault
Home › Cadillac › 2018 › CT6 Plug-In › Repair and Diagnosis › Engine Mechanical › Engine Mechanical - 2.0L (LTG) › Specifications › Fastener Specifications

Fastener Specifications

Single Use Non-Threaded Fasteners/Components

Application
NOTE:

All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. 
Camshaft Cover Gasket
Combustion Fuel Injector Seal
Connecting Rod Bearing
Cylinder Head Core Hole Plug
Cylinder Head Gasket
Engine Coolant Thermostat Gasket
Engine Oil Cooler Seal
Exhaust Manifold Gasket
Fuel Injector Seal Ring
Fuel Injector Spacer
Fuel Pump Gasket
Fuel Pump Housing Seal
Intake Manifold Gasket
Oil Pump Screen Gasket
Piston Pin Retainer
Positive Crankcase Ventilation Tube
Positive Crankcase Ventilation Valve
Thermostat Bypass Pipe Gasket
Throttle Body Gasket
Timing Chain Tensioner Gasket
Turbocharger Coolant Feed and Return Pipe Gasket
Turbocharger Coolant Feed and Return Pipe Washer
Turbocharger Gasket
Turbocharger Oil Feed Pipe Gasket
Turbocharger Oil Feed Pipe Washer
Turbocharger Oil Return Pipe Gasket
Vacuum Pump Gasket
Vacuum Pump Seal
Valve Stem Oil Seal
Water Outlet Gasket
Water Pump Gasket
Single Use Threaded Fastener/Component Tightening Specifications

NOTE:

All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. 
Application Specification
Metric (English)
Automatic Transmission Flex Plate Bolt
  • First Pass:
 20 N.m (15 lb ft)
  • Second Pass:
 30 N.m (22 lb ft)
  • Final Pass:
 40 degrees
Automatic Transmission Torque Dampener Bolt
  • First Pass:
 20 N.m (15 lb ft)
  • Second Pass:
 30 N.m (22 lb ft)
  • Final Pass:
 40 degrees
Balance Shaft Sprocket Bolt
  • First Pass:
 40 N.m (30 lb ft)
  • Final Pass:
 50 degrees
Camshaft Position Actuator Bolt
  • First Pass:
 30 N.m (22 lb ft)
  • Final Pass:
 100 degrees
Connecting Rod Bolt
  • First Pass:
 25 N.m (18 lb ft)
  • Final Pass:
 110 degrees
Crankshaft Balancer Bolt
  • First Pass:
 150 N.m (111 lb ft)
  • Final Pass:
 140 degrees
Cylinder Head Bolt
  • First Pass:
 30 N.m (22 lb ft)
  • Final Pass:
 190 degrees
Cylinder Head Core Hole Plug 50 N.m (37 lb ft)
Cylinder Head Oil Gallery Plug 40 N.m (30 lb ft)
Engine Front Cover Bolt - M10
  • First Pass:
 15 N.m (11 lb ft)
  • Final Pass:
 130 degrees
Exhaust Manifold Bolt 20 N.m (15 lb ft)
Exhaust Manifold Brace Nut 25 N.m (18 lb ft)
Fuel Feed Intermediate Pipe
  • First Pass:
 15 N.m (11 lb ft)
  • Final Pass:
 30 N.m (22 lb ft)
Fuel Pump Bolt
  • First Pass:
 8 N.m (71 lb in)
  • Final Pass:
 50 degrees
Lower Crankcase Bolt
  • First Pass:
 20 N.m (15 lb ft)
  • Final Pass:
 140 degrees
Oil Filter 3/4 to 1 full turn after gasket makes contact with the sealing surface on the filter mounting flange
Positive Crankcase Ventilation Valve Bolt 10 N.m (89 lb in)
Turbocharger Nut
  • First Pass:
 30 N.m (22 lb ft)
  • Second Pass:
 90 degrees
Reusable Threaded Fastener Tightening Specifications

NOTE:

All fasteners listed in this table can be reused after removal. 
Application Specification
Metric (English)
Balance Chain Guide Bolt 10 N.m (89 lb in)
Balancer Chain Tensioner Bolt 10 N.m (89 lb in)
Balancer Shaft with Oil Pump Bolt
  • First Pass:
 58 N.m (43 lb ft)
  • Final Pass:
 58 N.m (43 lb ft)
Camshaft Bearing Cap Bolt 10 N.m (89 lb in)
Camshaft Bearing Cap Bolt- Front 10 N.m (89 lb in)
Camshaft Cover Bolt 10 N.m (89 lb in)
Camshaft Cover Heat Shield Bolt 10 N.m (89 lb in)
Camshaft Cover Plug 35 N.m (26 lb ft)
Camshaft Position Actuator Solenoid Valve Bolt 10 N.m (89 lb in)
Camshaft Position Sensor Bolt 10 N.m (89 lb in)
Catalytic Converter Brace Bracket Bolt 10 N.m (89 lb in)
Crankshaft Position Sensor Bolt 10 N.m (89 lb in)
Drive Belt Tensioner Bolt 58 N.m (43 lb ft)
Engine Block Oil Gallery Plug 65 N.m (48 lb ft)
Engine Block Oil Gallery Plug 40 N.m (30 lb ft)
Engine Coolant Air Bleed Pipe Bolt 10 N.m (89 lb in)
Engine Coolant Heater 50 N.m (37 lb ft)
Engine Coolant Heater Hole Plug 60 N.m (44 lb ft)
Engine Coolant Thermostat Housing Bolt 10 N.m (89 lb in)
Engine Front Cover Bolt - M6 10 N.m (89 lb in)
Engine Front Cover Bolt - M8 25 N.m (18 lb ft)
Engine Lift Front Bracket Bolt 25 N.m (18 lb ft)
Engine Lift Rear Bracket Bolt 25 N.m (18 lb ft)
Engine Mount Bolt 58 N.m (43 lb ft)
Engine Mount Bracket Bolt 58 N.m (43 lb ft)
Engine Oil Cooler Bolt 10 N.m (89 lb in)
Engine Oil Cooler Connector 50 N.m (37 lb ft)
Engine Oil Level Indicator Switch Bolt 10 N.m (89 lb in)
Engine Oil Pressure Sensor 35 N.m (26 lb ft)
Exhaust Manifold Brace Bolt 25 N.m (18 lb ft)
Exhaust Manifold Heat Shield Bolt 14 N.m (124 lb in)
Fuel Feed Pipe 30 N.m (22 lb ft)
Fuel Feed Pipe Clip Stud 10 N.m (89 lb in)
Fuel Injection Fuel Rail Bolt 25 N.m (18 lb ft)
Fuel Injection Fuel Rail Fuel Pressure Sensor 33 N.m (24 lb ft)
Fuel Pump Shield Bolt 10 N.m (89 lb in)
Ignition Coil Bolt 10 N.m (89 lb in)
Intake Manifold Bolt 12 N.m (106 lb in)
Intake Manifold Cover Bolt 9 N.m (80 lb in)
Knock Sensor Bolt 25 N.m (18 lb ft)
Lower Crankcase Bolt 25 N.m (18 lb ft)
Lower Oil Pan Bolt 10 N.m (89 lb in)
Manifold Absolute Pressure Sensor Bolt 5 N.m (44 lb in)
Oil Pan Baffle Bolt 10 N.m (89 lb in)
Oil Pan Bolt 10 N.m (89 lb in)
Oil Pan Bolt 25 N.m (18 lb ft)
Oil Pan Drain Plug 25 N.m (18 lb ft)
Oil Pump Suction Pipe Bolt 10 N.m (89 lb in)
Oil Pump Flow Control Valve Bolt 10 N.m (89 lb in)
Piston Oil Nozzle Bolt 10 N.m (89 lb in)
Positive Crankcase Ventilation Hose Fastener 12 N.m (106 lb in)
Positive Crankcase Ventilation Hose Fitting Bolt 8 N.m (71 lb in)
Spark Plug 20 N.m (15 lb ft)
Thermostat Bypass Pipe Bolt 10 N.m (89 lb in)
Throttle Body Bolt 10 N.m (89 lb in)
Timing Chain Guide Bolt 25 N.m (18 lb ft)
Timing Chain Tensioner Bolt 25 N.m (18 lb ft)
Timing Chain Tensioner Shoe Bolt 25 N.m (18 lb ft)
Transmission Bolt 58 N.m (43 lb ft)
Transmission Fluid Cooler Pipe Bolt 22 N.m (16 lb ft)
Turbocharger Bypass Valve Solenoid Bolt 8 N.m (71 lb in)
Turbocharger Coolant Feed Pipe Bolt 10 N.m (89 lb in)
Turbocharger Coolant Feed Pipe Bolt 35 N.m (26 lb ft)
Turbocharger Coolant Return Pipe Bolt 35 N.m (26 lb ft)
Turbocharger Heat Shield Bolt 14 N.m (124 lb in)
Turbocharger Exhaust Pipe Stud 25 N.m (18 lb ft)
Turbocharger Oil Feed Pipe Bolt 10 N.m (89 lb in)
Turbocharger Oil Feed Pipe Bolt 35 N.m (26 lb ft)
Turbocharger Oil Return Pipe Bolt 10 N.m (89 lb in)
Turbocharger Wastegate Actuator Bolt 8 N.m (71 lb in)
Turbocharger Wastegate Regulator Solenoid Valve Bolt 8 N.m (71 lb in)
Vacuum Pump Bolt 10 N.m (89 lb in)
Water Outlet Bolt 10 N.m (89 lb in)
Water Pump Bolt 25 N.m (18 lb ft)
About FixVault