FixVault
Home › Chevrolet › 2005 › Blazer 2D Utility, 4WD, Part Time, Automatic › Repair and Diagnosis › External Pages › Different car › Section 6 (Computer/Integrating Systems) › Diagnostic Information and Procedures › Symptoms - Computer/Integrating Systems › Power Mode Mismatch › Test Description

Test Description

WARNING: This page is about a different car, the 2005 GMC Safari and 2005 Chevrolet Astro. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 5:  This step tests for battery voltage on the signal circuits that are not required.
  2. 6:  This step tests for no battery voltage on the required signal circuits.
  3. 7:  If any ignition switch parameters that should be inactive in the present ignition switch position are active, 2 ignition switch signal circuits may be shorted together.
  4. 8:  This step eliminates open circuits as the cause of the malfunction.
Power Mode Mismatch

Step Action Yes No
Schematic Reference: Body Control System Schematics 
Connector End View Reference: Computer/Integrating Systems Connector End Views 
DEFINITION: This table is used if the observed vehicle power mode does not match the ignition switch position.
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Install a scan tool.
  2. Turn OFF the ignition.
  3. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
Does the displayed power mode parameter match the actual ignition switch position?		 Go to Step 3  Go to Step 5 
3
  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
Does the displayed power mode parameter match the actual ignition switch position?		 Go to Step 4  Go to Step 5 
4
IMPORTANT: The engine may start during this procedure. Turn the ignition OFF after verifying this power mode.
  1. Turn the ignition switch to the CRANK position.
  2. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
Does the displayed power mode parameter match the actual ignition switch position?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 5 
5 
IMPORTANT: The engine may start during this procedure. Turn the ignition OFF after verifying this power mode.
  1. Turn OFF the ignition.
  2. Disconnect the power mode master (PMM).
  3. Hold the ignition switch in the position that indicated the incorrect power mode.
  4. With a test lamp attached to a good ground, test the PMM ignition switch inputs for voltage. Refer to Body Control System Description and Operation .
Is voltage present on only the inputs specified for the ignition switch position?		 Go to Step 6  Go to Step 7 
6 
IMPORTANT: The engine may start during this procedure. Turn the ignition OFF after verifying this power mode.
  1. Hold the ignition switch in the position that indicated the incorrect power mode.
  2. With a test lamp attached to a good ground, test the PMM ignition switch inputs for voltage. Refer to Body Control System Description and Operation .
Is voltage not present on any inputs specified for the ignition switch position?		 Go to Step 8  Go to Step 10 
7 
  1. Disconnect the ignition switch.
  2. Test the PMM ignition switch input circuits for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
  3. Test the PMM ignition switch circuits for a short between circuits. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
8 
  1. Disconnect the ignition switch.
  2. Test the PMM ignition switch input circuits for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
9 Inspect for poor connections and terminal tension at the harness connector of the ignition switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 11 
10 Inspect for poor connections and terminal tension at the harness connector of the PMM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
11 Replace the ignition switch. Refer to Ignition Switch Replacement in Steering Wheel and Column.
Did you complete the replacement?		 Go to Step 13  -
12 Replace the PMM. Refer to Control Module References  for replacement, setup and programming.
Did you complete the replacement?		 Go to Step 13  -
13
IMPORTANT: The engine may start during this procedure. Turn the ignition OFF after verifying all power modes.
  1. Reconnect all disconnected components.
  2. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
  3. Cycle the ignition switch through all possible positions one at a time.
Does the displayed power mode parameter match the actual ignition switch position?		 System OK Go to Step 2 
About FixVault