FixVault
Home › Chevrolet › 2011 › Impala LTZ › Repair and Diagnosis › External Pages › Different car › Section 1099 (Engine Cooling System) › Repair Instructions › Radiator Replacement › Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2010 Chevrolet Impala. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Removing/Installing Radiator Hoses To/From Radiator
    GM455227Courtesy of GENERAL MOTORS CORP.
  1. Install the radiator to the lower mounts.
    2. Fig 2: Condenser Hold Down Bracket & Mount Tabs
    GM1202952Courtesy of GENERAL MOTORS CORP.
    NOTE: Verify that the condenser is fully seated in the radiator mounting tabs.
  2. Install the condenser to the mounting tabs on the radiator (2).
  3. Install the condenser hold down bracket (1) to the radiator and condenser.
  4. Install the lower radiator hose to the radiator.
  5. Use J 38185:  Hose Clamp Pliers to install the lower radiator hose clamp to the radiator.
    6. Fig 3: View Of Cooling Fan Shroud Bolts
    GM1653094Courtesy of GENERAL MOTORS CORP.
    NOTE: Ensure the right and left edge of the fan shroud engages the radiator slots.
  6. Install the cooling fan shroud.
    7. CAUTION: Refer to Fastener Caution .
  7. Install the condenser tubes bracket bolt to the fan shroud and tighten to 10 N.m (89 lb in).
  8. Install the cooling fan motors electrical harness to the fan shroud clips.
  9. Connect the engine cooling fan motors electrical connectors.
  10. Install the cooling fan shroud bolts and tighten to 10 N.m (89 lb in).
  11. Connect the transaxle oil cooler pipes to the radiator. Refer to Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection .
    12. Fig 4: View Of Fan Shroud To Radiator Upper Support Brackets
    GM1202856Courtesy of GENERAL MOTORS CORP.
  12. Install the radiator upper support brackets and bolts that connect to the fan shroud and tighten to 6 N.m (53 lb in).
    13. Fig 5: Identifying Fan Shroud To Condenser Hold Down Bracket Bolt
    GM1202860Courtesy of GENERAL MOTORS CORP.
  13. Install the bolt that connects the fan shroud to the condenser hold down bracket and tighten to 6 N.m (53 lb in).
  14. Install the PCM harness clip on to the fan shroud.
  15. Install the upper radiator hose to the radiator.
  16. Use J 38185:  Hose Clamp Pliers to install the upper radiator hose clamp to the radiator.
  17. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement for the 3.5L engine or Air Cleaner Assembly Replacement for the 3.9L engine.
  18. Install the coolant reservoir hose to the fan shroud.
  19. Install the radiator vent hose to the right upper radiator tank and fill neck.
  20. Install the engine mount struts. Refer to Engine Mount Strut Replacement for the 3.5L engine or Engine Mount Strut Replacement for the 3.9L engine.
  21. Fill the cooling system. Refer to Cooling System Draining and Filling (9C1, 9C3 Static Fill)  or Cooling System Draining and Filling (LZE, LZ4, LGD, 9C1, 9C3, GE47716 Fill)  or Cooling System Draining and Filling (LZE, LZ4, LGD Static Fill) .
  22. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection (RPOs LZE/LZ4/LGD) .
    23. CAUTION: Do NOT overfill the transaxle. The overfilling of the transaxle causes foaming, loss of fluid, shift complaints, and possible damage to the transaxle.
  23. Adjust the transaxle fluid level.
About FixVault