FixVault
Home › Chevrolet › 2013 › Impala LS › Repair and Diagnosis › External Pages › Different car › Section 5 (Computer/Integrating Systems) › Diagnostic Information and Procedures › DTC B1385 › Test Description

Test Description

WARNING: This page is about a different car, the 2005 Buick LaCrosse and 2005 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 3:  This tests the ignition switch for a short circuit between the 12-volt reference supply circuit and the crank circuit in the OFF position.
  2. 4:  This tests the wiring of the crank circuit for a short to ground or voltage.
  3. 5:  This tests the ignition switch for a closed circuit between the ignition switch 12-volt reference supply circuit and the crank circuit in the Crank switch position. Care must be taken as the engine may crank during this test.
DTC B1385

Step Action Yes No
Schematic Reference: Body Control System Schematics  and Power Distribution Schematics in Wiring Systems
Connector End View Reference: Computer/Integrating Systems Connector End Views  and Master Electrical Component List in Wiring Systems
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Check for DTCs in the range of DTC B1370 to B1385 in the body control system (BCM).
Does the scan tool display DTC B1370 to DTC B1385 as current?		 Go to Step 3  Go to Diagnostic Aids
3 
  1. Disconnect the BCM harness connector that contains the crank circuit.
  2. Place the ignition switch in the OFF position, leaving the key in the ignition.
  3. Test for a short to ground and a short to voltage between the crank circuit and the ignition switch 12-volt reference supply circuit at the BCM harness connector. Refer to Body Control System Schematics  and Circuit Testing in Wiring Systems.
Did you find a short between the 2 circuits?		 Go to Step 4  Go to Step 5 
4 
  1. Disconnect the ignition switch harness connector.
  2. Test the crank ignition switch circuit and the ignition switch 12-volt reference supply circuit for a short to ground or voltage at the BCM harness connector. Refer to the following:
Did you find and correct the condition?		 Go to Step 9  Go to Step 7 
5 
IMPORTANT: The engine may crank during this procedure.
  1. Turn the ignition switch to the Crank position.
  2. Test for continuity between the crank terminal and the ignition switch 12-volt reference supply terminal on the BCM harness connector. Refer to Circuit Testing in Wiring Systems.
Can you measure continuity in Crank?		 Go to Step 8  Go to Step 6 
6 Test the crank and the ignition switch 12-volt reference supply terminals of the ignition switch harness connector, for intermittent or poor connections, and an open condition.
Did you find and correct the condition?		 Go to Step 9  Go to Step 7 
7 Replace the ignition switch. Refer to Ignition Switch Replacement in Steering Wheel and Column.
Did you complete the replacement?		 Go to Step 9  -
8 Replace the BCM. Refer to Control Module References  for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 9  -
9
  1. Reconnect all disconnected connectors.
  2. Install the scan tool.
  3. Turn ON the ignition, with the engine OFF.
  4. Use the scan tool in order to clear the DTCs.
  5. Operate the vehicle within the conditions for running the DTCs as specified in the supporting text.
Does the DTC reset?		 Go to Step 1  System OK
About FixVault