Common Specifications & Procedures

CRUZE LIMITED VIN P COMMON SPECIFICATIONS & PROCEDURES

System		Specification/Procedure
Air Conditioning
Service		APPROXIMATE FLUID CAPACITIES
Torque		Automatic System FASTENER SPECIFICATIONS Manual System FASTENER SPECIFICATIONS
Axle Nut/Hub Nut
Front		1st step 111 Ft. Lb. (150 N.m) 2nd step release tension 45 degrees 3rd step 184 Ft. Lb. (250 N.m)
Battery		NA
Brakes
Bleeding Sequence		RR, LR, RF, LF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL BLEEDING) or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE BLEEDING)
Disc Brakes
	Service Specifications	DISC BRAKE COMPONENT SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Drum Brakes
	Service Specifications	DRUM BRAKE COMPONENT SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Charging
Generator Usage		NA
Torque		See FASTENER SPECIFICATIONS (1.4L LUV)
Drive Belts
Adjustment		Serpentine drive belts are not adjustable.
Drive Belt Routing		1.4L See illustration under DRIVE BELT REPLACEMENT 1.8L See illustration under DRIVE BELT REPLACEMENT
Engine Cooling
General Service Specifications		APPROXIMATE FLUID CAPACITIES
	Radiator Cap Pressure	Specificaiton is stamped on pressure cap.
	Thermostat R & I	1.4L/1.8L ENGINE COOLANT THERMOSTAT REPLACEMENT
	Water Pump R & I
	1.4L	WATER PUMP REPLACEMENT (1.4L LUV)
	1.8L	WATER PUMP REPLACEMENT (1.8L LUW AND LWE)
Engine Mechanical
1.4L
	Compression	Maximum pressure differential 100 kPa (14.5 psi). See ENGINE COMPRESSION TEST
	Oil Pressure	At Idle 22 psi (150 kPa) At 3000-3500 RPM 55-94 psi (380-650 kPa)
	Overhaul	ENGINE MECHANICAL SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
1.8L
	Compression	ENGINE COMPRESSION TEST
	Oil pressure	Oil Pressure @ Idle Speed 22 psi (150 kPa) Oil Pressure @ 3000 rpm - 3500 rpm 55 - 94 psi (380 - 650 kpa)
Overhaul		ENGINE MECHANICAL SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Fluid Specifications		See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque
1.4L (Two-Mass)		Step 1 = 44 Ft. Lb. (60 N.m) Step 2 = + 45 degrees Step 3 = + 15 degrees
	1.8L	Step 1 = 44 Ft. Lb. (60 N.m) Step 2 = + 45 degrees Step 3 = + 15 degrees
Fuel System
Pressure Specification
1.4L & 1.8L		Energized With Scan Tool KOEO 50-94 PSI (345-650 kPa)
	Fuel Pressure Test Procedure	1.4L CIRCUIT/SYSTEM VERIFICATION 1.8L CIRCUIT/SYSTEM VERIFICATION
	Fuel Filter Location	1.4L The fuel strainer is attached to the lower end of the fuel pump module. 1.8L The fuel filter and strainer are attached to the lower end of the fuel pump module.
	Fuel Filter R & I	1.4L & 1.8L The fuel strainer is attached to the lower end of the fuel pump module and requires no maintenance. 1.4L FUEL TANK FUEL PUMP MODULE REPLACEMENT or 1.8L FUEL TANK FUEL PUMP MODULE REPLACEMENT
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)		Engine has coil-on-plug ignition.
Ignition Wires (Routing)		Engine has coil-on-plug ignition.
Spark Plug
1.4L (Type = Refer to Parts Catalogue)
	Gap	0.028 in (0.70 mm)
	Torque	18 Ft. Lb. (25 N.m)
1.8L (Type = Refer to Parts Catalogue)
	Gap	.024-.028 in (0.60-0.70 mm)
	Torque	18 Ft. Lb. (25 N.m)
Starting
Starter		N/A
Torque		FASTENER SPECIFICATIONS (1.4L LUV)
Wheel Alignment
	Adjustment Specifications	WHEEL ALIGNMENT SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque		103 Ft. Lb. (140 N.m) For Wheel Nut Tightening Sequence, See illustration under tire and wheel INSTALLATION PROCEDURE in Wheels And Tires.