FixVault
Home › Chevrolet › 2021 › Traverse L › Repair and Diagnosis › Body & Frame › Body, Cab Control Systems › Vehicle Access System › Diagnostic Information and Procedures › Door Ajar Indicator Malfunction › Circuit/System Testing

Circuit/System Testing

Test 1

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A23D Door Latch Assembly - Driver
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 3 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 3 @ Component harness & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On / Vehicle - In Service Mode
  5. Verify the scan tool parameter: Driver Door Ajar Switch = Inactive
    • If not the specified state 
    1. Ignition/Vehicle - Off
    2. Disconnect the appropriate electrical connector: M35D Window Motor Module - Driver or S79D Window Switch - Driver
    3. Test for infinite resistance between the test points: Signal circuit terminal 1 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: M35D Window Motor Module - Driver or S79D Window Switch - Driver
    • Go to next step: If the specified state 
  6. Connect a 3 A fused jumper wire between the test points: Signal circuit terminal 1 & Ground circuit terminal 3
  7. Verify the scan tool parameter: Driver Door Ajar Switch = Active
    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the appropriate electrical connector: M35D Window Motor Module - Driver or S79D Window Switch - Driver
    3. Ignition - On / Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 1 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points:
      • Signal circuit terminal 1 @ Component harness & Signal circuit terminal 6 @ M35D Window Motor Module - Driver
      • Signal circuit terminal 1 @ Component harness & Signal circuit terminal 10 @ S79D Window Switch - Driver
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: M35D Window Motor Module - Driver or S79D Window Switch - Driver
    • Go to next step: If the specified state 
  8. Test or replace the component: A23D Door Latch Assembly - Driver

Test 2

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A23P Door Latch Assembly - Passenger
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 3 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 3 @ Component harness & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On / Vehicle - In Service Mode
  5. Verify the scan tool parameter: Passenger Door Ajar Switch = Inactive
    • If not the specified state 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector. S79P Window Switch - Passenger
    3. Test for infinite resistance between the test points: Signal circuit terminal 5 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: S79P Window Switch - Passenger
    • Go to next step: If the specified state 
  6. Connect a 3 A fused jumper wire between the test points: Signal circuit terminal 5 & Ground circuit terminal 3
  7. Verify the scan tool parameter: Passenger Door Ajar Switch = Active
    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the electrical connector: S79P Window Switch - Passenger
    3. Ignition - On / Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 5 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points: Signal circuit terminal 5 @ Component harness & Signal circuit terminal 2 @ S79P Window Switch - Passenger
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: S79P Window Switch - Passenger
    • Go to next step: If the specified state 
  8. Test or replace the component: A23P Door Latch Assembly - Passenger

Test 3

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A23LR Door Latch Assembly - Left Rear
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 3 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 3 @ Component harness & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On / Vehicle - In Service Mode
  5. Verify the scan tool parameter: Left Rear Door Ajar Switch = Inactive
    • If not the specified state 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: S79LR Window Switch - Left Rear
    3. Test for infinite resistance between the test points: Signal circuit terminal 1 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: S79LR Window Switch - Left Rear
    • Go to next step: If the specified state 
  6. Connect a 3 A fused jumper wire between the test points: Signal circuit terminal 1 & Ground circuit terminal 3
  7. Verify the scan tool parameter: Left Rear Door Ajar Switch = Active
    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the electrical connector: S79LR Window Switch - Left Rear
    3. Ignition - On / Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 1 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points: Signal circuit terminal 1 @ Component harness & Terminal 2 @ S79LR Window Switch - Left Rear
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: S79LR Window Switch - Left Rear
    • Go to next step: If the specified state 
  8. Test or replace the component: A23LR Door Latch Assembly - Left Rear

Test 4

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A23RR Door Latch Assembly - Right Rear
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 3 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 3 @ Component harness & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On / Vehicle - In Service Mode
  5. Verify the scan tool parameter: Right Rear Door Ajar Switch = Inactive
    • If not the specified state 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: S79RR Window Switch - Right Rear
    3. Test for infinite resistance between the test points: Signal circuit terminal 5 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: S79RR Window Switch - Right Rear
    • Go to next step: If the specified state 
  6. Connect a 3 A fused jumper wire between the test points: Signal circuit terminal 5 & Ground circuit terminal 3
  7. Verify the scan tool parameter: Right Rear Door Ajar Switch = Active
    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the electrical connector: S79RR Window Switch - Right Rear
    3. Ignition - On / Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 5 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points: Signal circuit terminal 5 @ Component harness & Terminal 2 @ S79RR Window Switch - Right Rear
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: S79RR Window Switch - Right Rear
    • Go to next step: If the specified state 
  8. Test or replace the component: A23RR Door Latch Assembly - Right Rear
About FixVault