FixVault
Home › Chevrolet › 2022 › Camaro LS, Automatic Trans › Repair and Diagnosis › External Pages › Different variant/trim › Section 9 (Engine Mechanical - 6.2L - Specifications) › Specifications › Fastener Specifications

Fastener Specifications

WARNING: This page is about a different variant/trim than selected.
Single Use Non-Threaded Fasteners/Components

Application
NOTE:

All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. 
Camshaft Actuator Magnet Gasket
Camshaft Position Actuator Solenoid Valve
Camshaft Position Sensor Seal
Charge Air Cooler Cover Gasket
Clutch Pilot Bearing
Crankshaft Front Oil Seal
Crankshaft Rear Oil Seal
Crankshaft Rear Oil Seal Housing Gasket
Cylinder Head Gasket
Engine Coolant Manifold Gasket
Engine Oil Cooler Core Seal
Engine Oil Cooler Gasket
Exhaust Manifold Bolt
Exhaust Manifold Gasket
Fuel Feed Intermediate Pipe - Position 1
Fuel Feed Intermediate Pipe - Position 2
Fuel Injector Dust Seal
Fuel Injector O-ring
Fuel Injector Plastic Spacer
Fuel Injector Retaining Clip
Fuel Injector Seal
Fuel Pump Gasket
Intake Manifold Gasket
Lower Oil Pan
Oil Level Indicator Switch Seal
Oil Pan Front Seal
Oil Pan High Pressure Port Seal
Oil Pump Screen Seal
Positive Crankcase Ventilation Oil Separator Drain Tube O-ring
Positive Crankcase Ventilation Tube Seal
Supercharger Assembly Gasket
Supercharger Water Manifold Gasket
Throttle Body Gasket
Turbocharger Coolant Feed and Return Pipe Gasket
Valve Lifter Oil Manifold Gasket
Valve Rocker Arm Cover Gasket
Water Pump Assembly Gasket
Water Pump Outlet Gasket
Single Use Threaded Fastener/Component Tightening Specifications

Application Specification
Metric (English)
NOTE:

All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. 
Automatic Transmission Flex Plate Bolt
  • First Pass:
 15 N.m (133 lb in)
  • Second Pass:
 30 N.m (22 lb ft)
  • Final Pass:
 45 degrees
Camshaft Position Actuator Solenoid Valve
  • First Pass:
 65 N.m (48 lb ft)
  • Final Pass:
 90 degrees
Connecting Rod Bolt
  • First Pass:
 20 N.m (15 lb ft)
  • Final Pass:
 85 degrees
Crankshaft Balancer Bolt - New Bolt with Flanged Head
  • First Pass:
 150 N.m (111 lb ft)
  • Second Pass:
 Loosen 360 degrees
  • Third Pass:
 80 N.m (59 lb ft)
  • Final Pass:
 125 degrees
Crankshaft Balancer Bolt - New Bolt with Retained Rotating Washer
  • First Pass:
 150 N.m (111 lb ft)
  • Second Pass:
 Loosen 360 degrees
  • Third Pass:
 80 N.m (59 lb ft)
  • Final Pass:
 200 degrees
Crankshaft Bearing Cap Bolt
  • Inner Bearing Cap Bolt - First Pass in Sequence
 20 N.m (15 lb ft)
  • Inner Bearing Cap Bolt - Final Pass in Sequence
 110 degrees
  • Outer Bearing Cap Bolt - First Pass in Sequence
 20 N.m (15 lb ft)
  • Outer Bearing Cap Bolt - Final Pass in Sequence
 80 degrees
  • Bearing Cap Side Bolts - First Pass in Sequence
 25 N.m (18 lb ft)
  • Bearing Cap Side Bolts - Final Pass in Sequence
 60 degrees
Cylinder Head Bolt
  • Cylinder Head Bolts - Internal Hex - LH Cylinder Head forwardmost fastener - First Pass in Sequence
 80 N.m (59 lb ft)
  • Cylinder Head Bolts - Internal Hex - LH Cylinder Head forwardmost fastener - Second Pass in Sequence
 90 degrees
  • Cylinder Head Bolts - Internal Hex - LH Cylinder Head forwardmost fastener - Final Pass in Sequence
 40 degrees
  • Cylinder Head Bolts - Standard Hex - First Pass in Sequence
 80 N.m (59 lb ft)
  • Cylinder Head Bolts - Standard Hex - Second Pass in Sequence
 90 degrees
  • Cylinder Head Bolts - Standard Hex - Final Pass in Sequence
 60 degrees
Engine Mount Fastener
  • First Pass:
 58 N.m (43 lb ft)
  • Final Pass:
 60 - 75 degrees
Engine Oil Cooler Hose Connector 35 N.m (26 lb ft)
Fuel Feed Intermediate Pipe Fitting 30 N.m (22 lb ft)
Exhaust Manifold Bolt - NEW Cylinder Head
  • First Pass:
 27 N.m (20 lb ft)
  • Second Pass:
 Loosen 180 degrees
  • Final Pass:
 23 N.m (17 lb ft)
Exhaust Manifold Bolt - Existing Cylinder Head 23 N.m (17 lb ft)
Flywheel Bolt
  • First Pass:
 15 N.m (11 lb ft)
  • Second Pass:
 30 N.m (22 lb ft)
  • Final Pass:
 45 degrees
Oil Filter 3/4 to 1 full turn after gasket makes contact with the sealing surface on the filter mounting flange
Oil Flow Check Valve 35 N.m (26 lb ft)
Supercharger to Block Bolts
  • First Pass in Sequence
 10 N.m (89 lb in)
  • Final Pass in Sequence
 10 N.m (89 lb in)
Reusable Threaded Fastener Tightening Specifications

Application Specification
Metric (English)
NOTE:

All fasteners listed in this table can be reused after removal. 
Accessory Drive Belt Tensioner Bolt - Lower 22 N.m (16 lb ft)
Camshaft Position Actuator Magnet Bolt 10 N.m (7 lb ft)
Camshaft Position Sensor Bolt 25 N.m (18 lb ft)
Camshaft Position (CMP) Sensor Wire Harness Bolt 10 N.m (7 lb ft)
Camshaft Retainer Bolt - TORX Head Bolt 15 N.m (11 lb ft)
Charge Air Cooler Cover Ball Stud 10 N.m (89 lb in)
Charge Air Cooler Cover Bolt 10 N.m (89 lb in)
Charge Air Cooler Cover Double Ended Stud 10 N.m (89 lb in)
Charge Air Regulator Solenoid Valve Bolt 10 N.m (89 lb in)
Cooler Line Bracket Bolt 10 N.m (89 lb in)
Crankshaft Balancer Bolt - Installation Pass with Used Bolt - to Ensure the Balancer is Completely Installed 330 N.m (244 lb ft)
Crankshaft Oil Deflector Bolt 10 N.m (89 lb in)
Crankshaft Position Sensor Bolt 25 N.m (18 lb ft)
Crankshaft Rear Oil Seal Housing Bolt 25 N.m (18 lb ft)
Drive Belt Tensioner Bolt 58 N.m (43 lb ft)
Engine Block Coolant Drain Hole Plug 60 N.m (44 lb ft)
Engine Block Coolant Heater 50 N.m (37 lb ft)
Engine Block Oil Gallery Plug @ Front 25 N.m (18 lb ft)
Engine Block Oil Gallery Plug @ Rear 30 N.m (22 lb ft)
Engine Coolant Manifold Bolt 25 N.m (18 lb ft)
Engine Coolant Temperature Sensor @ Engine Coolant Manifold 20 N.m (15 lb ft)
Engine Coolant Temperature Sensor @ Oil Filter Adapter 22 N.m (16 lb ft)
Engine Front Cover Bolt 25 N.m (18 lb ft)
Engine Harness Fastener 10 N.m (89 lb in)
Exhaust Manifold Heat Shield Bolt 10 N.m (89 lb in)
Engine Oil Cooler Adapter to Oil Pan Bolt (M6) 10 N.m (89 lb in)
Engine Oil Cooler Adapter to Oil Pan Bolt (M8) 25 N.m (18 lb ft)
Engine Oil Cooler Coolant Fitting 35 N.m (26 lb ft)
Engine Oil Cooler Core Bolt 25 N.m (18 lb ft)
Engine Oil Level and Temperature Sensor Bolt 10 N.m (89 lb in)
Engine Oil Pressure Sensor 35 N.m (26 lb ft)
Engine Wiring Harness Bolt (Rear Engine Channel) 10 N.m (89 lb in)
Engine Wiring Harness Jumper Bracket Bolt 25 N.m (18 lb ft)
Evaporative Emission Canister Purge Solenoid Valve Bolt 10 N.m (89 lb in)
Flex Plate to Torque Converter Fastener 60 N.m (44 lb ft)
Flywheel Inspection Cover Bolt 10 N.m (89 lb in)
Fuel Feed Pipe Bolt 10 N.m (89 lb in)
Fuel Injection Fuel Rail Bolt 25 N.m (18 lb ft)
Fuel Injection Fuel Rail Crossover Pipe Bolt 10 N.m (89 lb in)
Fuel Injection Fuel Rail Crossover Pipe Fitting 28 N.m (21 lb ft)
Fuel Injection Fuel Rail Fuel Pressure Sensor 33 N.m (24 lb ft)
Fuel Pump Bolt 25 N.m (18 lb ft)
Fuel Pump Lifter Follower Guide Bolt 25 N.m (18 lb ft)
Generator Bracket Bolt 50 N.m (37 lb ft)
Ignition Coil Bracket-to-Valve Rocker Arm Cover Bolt 10 N.m (89 lb in)
Inlet Air Pressure and Temperature Sensor Bolt 10 N.m (89 lb in)
Intake Manifold Bolt
  • First Pass in Sequence
 5 N.m (44 lb in)
  • Final Pass in Sequence
 10 N.m (89 lb in)
Intake Manifold Cover Bolt 4.5 N.m (40 lb in)
Intake Manifold Cover Stud 4.5 N.m (40 lb in)
Jumper Harness Bolt 25 N.m (18 lb ft)
Knock Sensor Bolt 25 N.m (18 lb ft)
Knock Sensor Heat Shield Bolt 25 N.m (18 lb ft)
Manifold Absolute Pressure Sensor Bolt - Intake Manifold 4.5 N.m (40 lb in)
Manifold Absolute Pressure Sensor Bolt - Supercharger 10 N.m (89 lb in)
Oil Filter Fitting 55 N.m (41 lb ft)
Oil Level Indicator Tube Bolt 10 N.m (89 lb in)
Oil Pan Cover Bolt 10 N.m (89 lb in)
Oil Pan Drain Plug 25 N.m (18 lb ft)
Oil Pan Bolt - Oil Pan-to-Rear Housing 12 N.m (106 lb in)
Oil Pan Bolt - Oil Pan-to-Engine Block and Oil Pan-to-Front Cover 25 N.m (18 lb ft)
Oil Pan Bolt - Lower Oil Pan to Upper Oil Pan 10 N.m (89 lb in)
Oil Pump Screen Bolt 10 N.m (89 lb in)
Oil Pump-to-Engine Block Bolt 25 N.m (18 lb ft)
Positive Crankcase Ventilation Valve LT1 6 N.m (53 lb in)
Positive Crankcase Ventilation Valve LT4 10 N.m (89 lb in)
Positive Crankcase Ventilation Oil Separator Bolt 10 N.m (89 lb in)
Spark Plug 20 N.m (15 lb ft)
Starter Heat Shield Bolt - Side 10 N.m (89 lb in)
Starter Heat Shield Bolt - Rear 25 N.m (18 lb ft)
Supercharger Belt Idler Pulley Bolts - All 58 N.m (43 lb ft)
Supercharger Belt Idler Pulley Bracket Bolts 25 N.m (18 lb ft)
Supercharger Water Manifold Bolt 10 N.m (89 lb in)
Supercharger Bypass Valve Actuator Bolt 27 N.m (20 lb ft)
Supercharger Inlet Air Pressure and Temperature Sensor Bolt 10 N.m (89 lb in)
Throttle Body Bolt 10 N.m (89 lb in)
Timing Chain Tensioner Bolt 25 N.m (18 lb ft)
Transmission to Engine Fastener 50 N.m (37 lb ft)
Transmission to Oil Pan Bolt 50 N.m (37 lb ft)
Valve Lifter Follower Guide Bolt 12 N.m (106 lb in)
Valve Lifter Oil Manifold Bolt
  • First Pass in Sequence
 15 N.m (11 lb ft)
  • Final Pass in Sequence
 30 N.m (22 lb ft)
Valve Lifter Oil Manifold Filter Plug 30 N.m (22 lb ft)
Valve Rocker Arm Bolt 30 N.m (22 lb ft)
Valve Rocker Arm Cover Bolt - In Sequence 10 N.m (89 lb in)
Water Pump Assembly Bolt 10 N.m (89 lb in)
Water Pump Outlet Bolt 10 N.m (89 lb in)
About FixVault