FixVault
Home › Chrysler › 2007 › Pacifica Base, 3.8 L › Repair and Diagnosis › Quick Lookups › Technical Bulletins › Campaigns › Engine Control Systems › Emissions Recall G04 - Reprogram Pcm (G04)

Emissions Recall G04 - Reprogram Pcm (G04)

Publication date: 2007-03-01
Reference number: G04

EMISSIONS RECALL G04 - REPROGRAM PCM

EMISSIONS RECALL G04 - REPROGRAM PCM

SERVICE CAMPAIGN BULLETIN

Reference Number(s): G04, Date of Issue:  March, 2007
CHRYSLER: 2007 (CS) Chrysler Pacifica

MODELS

2007 (CS) Chrysler Pacifica 

NOTE: This recall applies only to the above vehicles equipped with a 4.0L engine  ("X" in the 8th VIN position) and a California Emission Control System (sales code NAE)  built through December 13, 2006 (MDH: 121321). 
IMPORTANT: Some of the involved vehicles may be in dealer new vehicle inventory. Dealers should complete this recall service on these vehicles before retail delivery.  Dealers should also perform this recall on vehicles in for service. Involved vehicles can be determined by using the VIP inquiry process.

SUBJECT

The Powertrain Control Module (PCM) on about 2600 of the above vehicles was inadvertently programmed with software that may not adequately control NOx emissions levels under certain operating conditions. This may cause the vehicle to release air pollutants which exceed California standards.

REPAIR

The Powertrain Control Module (PCM) must be reprogrammed (flashed).

PARTS INFORMATION

Each vehicle  requires application of the following label:

PARTS INFORMATION

Part Number  Description 
04275086AB Authorized Modifications Label

Due to the likelihood that the required labels are already in your parts inventory, no labels will be distributed initially. The following label may be ordered as needed.

SPECIAL TOOLS

The following special tools may be required to perform this repair: 

* Part of CH9400 kit.

SERVICE PROCEDURE

NOTE: Either StarSCAN or StarMOBILE can be used to perform this recall. This procedure must be performed with release 7.03 or later. A CD containing software release 7.03 was sent to each dealer at the end of January, 2007. If the reprogramming flash for the PCM is aborted or interrupted, repeat the procedure.

A. Program the PCM using StarSCAN

  1. Open the hood. Install a battery charger and verify that the charging rate provides 13.0 to 13.5 volts. Do not allow the charger to time out during the flash process. Set the battery charger timer (if so equipped) to continuous charge.
    NOTE: Use an accurate stand alone voltmeter. The battery charger volt meter may not be sufficiently accurate. Voltages outside of the specified range will cause an unsuccessful flash. If voltage reading is too high, apply an electrical load by activating the park or headlamps and/or HVAC blower motor to lower the voltage.
  2. Connect the CH9410 StarSCAN ethernet cable to the StarSCAN and the dealer's network drop.
  3. Connect the CH9404 StarSCAN vehicle cable to the StarSCAN and the vehicle.
  4. Place the Ignition in the "RUN"  position, then Power "ON"  the StarSCAN.
  5. Retrieve the old PCM part number. With the StarSCAN on the "Home"  screen, follow the procedure below:
    1. Select "ECU View"  .
    2. Touch the screen to highlight "PCM"  in the list of modules.
    3. Select "More Options"  .
    4. Select "ECU Flash"  .
    5. Record the "Part Number"  displayed at the end of the "Resident flash file for" statement near the top of "Flash PCM"  screen for later reference.
  6. Download the flash file from the internet to the StarSCAN. With the StarSCAN on the "Flash PCM"  screen, follow the procedure below:
    1. Select "Browse for New File"  . Follow the on screen instructions.
    2. If the newly downloaded flash file "Part Number" description is the same as the number recorded in Step   e , then the PCM is up to date and reprogramming is not required. Continue to Step  10.
    3. Highlight the listed calibration on the StarSCAN screen.
    4. Select "Download to Scantool"  .
    5. Select "Close"  after the download is complete, then select "Back"  .
    6. Highlight the listed calibration.
    7. Select "Update Controller"  and follow the on screen instructions.
    8. When the update is completed, select "OK"  .
  7. Disconnect the CH9404 StarSCAN vehicle cable from the vehicle. Wait until the StarSCAN screen reads "Vehicle Disconnected"  , then press "OK"  .
  8. Reconnect the CH9404 StarSCAN vehicle cable to the vehicle.
  9. Retrieve the PCM part number. With the StarSCAN on the "Home"  screen, follow the procedure below:
    1. Select "ECU View"  .
    2. Touch the screen to highlight "PCM"  in the list of modules.
    3. Select "More Options"  .
    4. Select "ECU Flash"  .
    5. Verify the "Part Number"  (displayed at the end of the "Resident flash file for" statement) has been updated to the new part number. If it has updated, then the flash has been completed successfully.
  10. Clear any Diagnostic Trouble Codes (DTCs) as follows:
    NOTE: Due to the PCM programming procedure, DTC(s) may be set in other modules (TCM, ABS, BCM, MIC, WCM, etc.) within the vehicle, if so equipped. Some DTC's may cause the MIL to illuminate.
    1. From the "Home"  screen select "System View"  .
    2. Select "All DTCs"  .
    3. Press "Clear All Stored DTCs"  if there are any DTCs shown on the list.
  11. Turn the ignition key to the "OFF"  position and remove the StarSCAN unit, StarSCAN cable, jumper battery and charger from the vehicle.

B. Reprogram the PCM Module Using StarMOBILE

  1. Open the hood and install a battery charger. Verify that the charging rate provides approximately 13.5 volts. Do not allow the charger to time out during the flash process. Set the battery charger timer (if so equipped) to continuous charge.
    NOTE: Use an accurate stand alone voltmeter. The battery charger volt meter may not be sufficiently accurate. Voltages outside of the specified range will cause an unsuccessful flash. If voltage reading is too high, apply an electrical load by activating the park or headlamps and/or HVAC blower motor to lower the voltage.
  2. Connect the StarMOBILE scan tool to the vehicle data link connector located under the steering column and turn the ignition key to the "RUN"  position.
  3. Power ON the StarMOBILE scan tool.
  4. Connect the CH9410 StarMOBILE scan tool ethernet cable to the StarMOBILE and the dealer's network drop.
  5. From the desktop, launch the "StarMOBILE Desktop Client" software.
  6. Establish a connection with the StarMOBILE scan tool.
  7. Select "Flash Download"  .
  8. Select "Next"  and then enter your ID and password.
  9. Enter the vehicle information (manually or use the automatic function).
  10. Highlight the required flash file and select "Download to Client"  .
  11. Select "BACK"  then select "ECU View"  .
  12. Select "PCM"  .
  13. Select "More Options"  .
  14. Select "ECU Flash"  .
  15. Select "Manage Files"  .
  16. Highlight downloaded flash file.
  17. Select "Copy to SM Device"  and then follow the screen prompts.
  18. Disconnect the ethernet cable from the StarMOBILE scan tool.
  19. Turn off the StarMOBILE scan tool and then restart the scan tool.
    NOTE: The StarMOBILE scan tool must be shut down and restarted to unlock the flash.
  20. From the "System Status" screen press the "Exit"  button.
  21. From the "Main Menu" select "Enter Standalone Diagnostic Mode"  and press the select button.
  22. Select "ECU View"  and press the select button.
  23. Highlight "PCM" and press the select button.
  24. Select "FLASH ECU"  and press the select button.
  25. Compare the highlighted software part number with the software part number displayed at the top of the screen.
    • If the part numbers are the same, the module is up to date and reprogramming is not required.  Continue to Step  28.
    • If the software part numbers are different, press the select button to reprogram the module.
  26. Verify the file number on the screen. If correct press the select button and follow the screen prompts.
  27. When the flash is complete, press the "OK" button.
  28. Clear any Diagnostic Trouble Codes (DTCs) as follows:
    NOTE: Due to the PCM programming procedure, DTC(s) may be set in other modules (TCM, ABS, BCM, MIC, WCM, etc.) within the vehicle, if so equipped. Some DTC's may cause the MIL to illuminate.
    1. From the "Standalone Home"  screen highlight "All DTC's"  and then press the select button.
    2. Highlight "Clear All Stored"  and then press the select button.
    3. Follow the screen prompts on the StarMOBILE screen.
  29. Turn the ignition key to the "OFF"  position and remove the StarMOBILE unit, StarMOBILE cable, and battery charger from the vehicle.

C. Install the Authorized Modifications Label

  1. Type or print (with a ballpoint pen) the recall number, dealer code and date on the Authorized Modifications Label (Figure 1  ).
  2. Attach the label near the VECI label and then close the hood.
    G07709438
  3. Complete Proof of Correction Form for California Residents: 

    This recall is subject to the State of California Registration Renewal / Emissions Recall Enforcement Program  . Complete a Vehicle Emission Recall Proof of Correction Form (Form No. 81-016-1053)  and supply it to vehicle owners residing in the state of California  for proof that this recall has been performed when they renew the vehicle registration.

COMPLETION REPORTING AND REIMBURSEMENT

Claims for vehicles that have been serviced must be submitted on the DealerCONNECT Claim Entry Screen located on the Service tab. Claims submitted will be used by DaimlerChrysler to record recall service completions and provide dealer payments.

Use one  of the following labor operation numbers and time allowances:

LABOR OPERATION NUMBER AND TIME ALLOWANCE

  Labor Operation Number  Time Allowance
PCM Update Previously Performed 08-G0-41-81 0.2 hours
Reprogram Powertrain Control Module 08-G0-41-82 0.5 hours

Add the cost of the label plus applicable dealer allowance to your claim.

NOTE: See the Warranty Administration Manual, Recall Claim Processing Section, for complete recall claim processing instructions.

DEALER NOTIFICATION

All dealers will receive three copies of this dealer recall notification letter by mail. To view this notification on DealerCONNECT, select "Global Recall System" on the Service tab, then click on the description of this notification.

OWNER NOTIFICATION AND SERVICE SCHEDULING

All involved vehicle owners known to DaimlerChrysler are being notified of the service requirement by first class mail. They are requested to schedule appointments for this service with their dealers. A generic copy of the owner letter is attached.

Enclosed with each owner letter is an Owner Notification postcard to allow owners to update our records if applicable.

VEHICLE LISTS, GLOBAL RECALL SYSTEM, VIP AND DEALER FOLLOW UP

All involved vehicles have been entered into the DealerCONNECT Global Recall System (GRS) and Vehicle Information Plus (VIP) for dealer inquiry as needed.

GRS provides involved dealers with an updated  VIN list of their incomplete  vehicles. The owner's name, address and phone number are listed if known. Completed vehicles are removed from GRS within several days of repair claim submission.

To use this system, click on the "Service"  tab and then click on "Global Recall System."  Your dealer's VIN list for each recall displayed can be sorted by: those vehicles that were unsold at recall launch, those with a phone number, city, zip code, or VIN sequence.

Dealers must perform this repair on all unsold vehicles before retail delivery.  Dealers should also use the VIN list to follow up with all owners to schedule appointments for this repair.

Recall VIN lists may contain confidential, restricted owner name and address information that was obtained from the Department of Motor Vehicles of various states. Use of this information is permitted for this recall only and is strictly prohibited from all other use  .

ADDITIONAL INFORMATION

If you have any questions or need assistance in completing this action, please contact your Service and Parts District Manager.

Customer Services Field Operations

DaimlerChrysler Corporation

EMISSIONS RECALL G04 - REPROGRAM PCM

Dear: (Name)

DaimlerChrysler has determined that some 2007 Chrysler Pacifica vehicles may be releasing air pollutants which exceed California standards.

The problem is...  The Powertrain Control Module (PCM) on your vehicle (VIN: xxxxxxxxxxxxxxxxx) was inadvertently programmed with software that may not adequately control NOx emission levels under certain operating conditions.

What your dealer will do... DaimlerChrysler will repair your vehicle free of charge (parts and labor).  To do this, your dealer will reprogram your vehicle's Powertrain Control Module. The work will take about 1/2 an hour to complete. However, additional time may be necessary depending on service schedules.

What you must do...  Simply contact your dealer  right away to schedule a service appointment.

If you need help...  If you have questions or concerns which your dealer is unable to resolve, please contact DaimlerChrysler at 1-800-853-1403.

California residents... The State of California requires the completion of emission recall repairs prior to vehicle registration renewal.  Your dealer will provide you with a Vehicle Emission Recall Proof of Correction Form after the recall service is performed. Be sure to save this form since the California Department of Motor Vehicles may require that you supply it as proof that the recall has been performed.

Please help us update our records, by filling out the attached prepaid postcard, if any of the conditions listed on the card apply to you or your vehicle.

If you have already experienced this condition and have paid to have it repaired, you may send your original receipts and/or other adequate proof of payment to the following address for reimbursement: DaimlerChrysler P.O. Box 4639 Oak Ridge, TN 37831, Attention: Reimbursement.

In order to ensure your full protection under the emission warranty made applicable to your vehicle by Federal law and your right to participate in future recalls, it is recommended that you have your vehicle serviced as soon as possible. Failure to do so could legally be determined to be a lack of proper maintenance of your vehicle. Further, without this repair, your vehicle may fail a state or local emission inspection test.

We are sorry for any inconvenience but trust that you understand our interest in clean air. Thank you for your attention to this important matter.

Customer Services Field Operations

DaimlerChrysler Corporation

Notification Code G04

About FixVault