FixVault
Home › Dodge and Ram › 2023 › Durango R/T Plus, AWD › Repair and Diagnosis › Suspension › Front Suspension And Wheel Alignment › Wheel Alignment › Technical Specifications › Measurement Specifications

Measurement Specifications

NOTE:

Specifications are in degrees. 

NOTE:

Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle's measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications.

Front Alignment Specifications
  Total Toe (1) Caster Caster Cross Caster Left Camber Right Camber Cross Camber
Base Suspension 
SDA 		 0.20° +/- 0.20° 6.95° +/- 0.60° 6.95° +/- 0.60° 0.00° +/- 0.60° -0.38° +/- 0.60° -0.78° +/- 0.60° 0.40° +/- 0.60°
Sport and Aero + Pursuit ECO III 
SDB SDE SD2 		 0.20° +/- 0.20° 7.46° +/- 0.60° 7.46° +/- 0.60° 0.00° +/- 0.60° -0.72° +/- 0.60° -1.12° +/- 0.60° 0.40° +/- 0.60°
SRT 
SDK SDX 		 0.20° +/- 0.20° 6.67° +/- 0.55° 6.67° +/- 0.55° 0.00° +/- 0.60° -1.68° +/- 0.60° -1.98° +/- 0.60° 0.30° +/- 0.60°
Tow-N-Go 
SDE and AAN 		 0.20° +/- 0.20° 6.67° +/- 0.55° 6.67° +/- 0.55° 0.00° +/- 0.60° -1.68° +/- 0.60° -1.98° +/- 0.60° 0.30° +/- 0.60°
Notes:
Positive toe (+) is toe-in and negative toe (-) is Toe-out.
(1) TOTAL TOE is the sum of both the left and right wheel toe settings. TOTAL TOE should be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe.
Rear Alignment Specifications
  Toe Total Toe (1) Thrust Angle Camber Cross Camber
Base Suspension 
SDA 		 0.10° +/- 0.15° 0.20° +/- 0.30° 0.00° +/- 0.15° -0.54° +/- 0.55° 0.00° +/- 0.60°
Sport and Aero + Pursuit ECO III 
SDB SDE SD2 		 0.10° +/- 0.15° 0.20° +/- 0.30° 0.00° +/- 0.15° -0.96° +/- 0.55° 0.00° +/- 0.60°
SRT 
SDK SDX 		 0.13° +/- 0.15° 0.25° +/- 0.30° 0.00° +/- 0.15° -1.30° +/- 0.55° 0.00° +/- 0.60°
Tow-N-Go 
SDE and AAN 		 0.13° +/- 0.15° 0.25° +/- 0.30° 0.00° +/- 0.15° -1.30° +/- 0.55° 0.00° +/- 0.60°
Notes:
Positive toe (+) is toe-in and negative toe (-) is Toe-out.
(1) TOTAL TOE is the sum of both the left and right wheel toe settings. TOTAL TOE should be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe.
About FixVault