Technical Service Bulletins

• A/C Compressor
  • Filtering Refrigerant After Compressor Replacement (98-12-5)
  • Identification Of Non-Ford Approved Refrigerants (99-19-6)
  • A/C - R-12 To R-134A Retrofit Kit - Factory A/C Only (98-4-8)
  • Use Of R-12 Refrigerant Substitutes (96-17-10)
  • A/C System Service - List Of Bulletins To Reference (96-15-6)
  • Ford Approved Flushing Procedures For A/C System (95-8-1)
  • R-12 Refrigerant Substitutes - Service Tip (94-14-3)
  • Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
  • Use Of Correct Fluorescent Tracer Dye - Service Tip (93-20-6)
  • A/C SLC Refrigerant Fittings Cleaning/New O-Ring Kit (93-6-5)
  • New Refrigerant Fitting "O" Rings (91-22-5)
  • Air Conditioning - Refrigerant R-12 - Service Tips (91-9-7)
  • A/C "O" Ring Usage Table (90-14-8)
  • Poor A/C - Clutch Pressure Cycling Switch Diagnosis (89-14-10)
  • A/C Drier - Replace When Major Component Serviced (88-25-5)
  • A/C Clutch Cycling Pressure Switch Diagnosis (87-6-4)
  • A/C Clutch Damage From OVERTIGHTEN - Torque Wrench (86-22-7)
  • A/C Clutch Pressure Cycling Switch Diagnostic (89-7T-19)
• Accessories Control Systems
  • Temp. Gauge Reads Low - Obsolete Temperature Sender (95-13-2)
  • EATC Display Dim Or Blank - Burned Out Bulbs (93-23-13)
  • Latches - Door - Replacement Required (91-8-4)
  • Inaccurate Speedo Readings - Mechanical & Electronic (89-2-7)
  • "Popping" Noise From Speakers: Suppression Capacitor (88-20-5)
• Anti-Lock Brakes
  • Brakes - Roughness Concern During Brake Application (95-6-2)
  • False Abs Light - High Tension Ignition Wire Routing (87-17-4)
  • Abs Module Testing Caution (87-12-3)
  • Abs Testing - New Super Star Testing Procedure (87-2-8)
  • Abs Code 61 Diagnosis - Memory Self Clears (86-25-8)
• Anti-Theft Systems
  • No Crank - Low State Of Battery Charge (91-10-8)
  • Latches - Door - Replacement Required (91-8-4)
  • Treating Cosmetic Paint Damage From AIRBORN Material (89-13-3)
  • Manual Vent Windows - Glass Sticks To Weatherstrip (88-14-1)
  • Power Door Locks Inoperative - Rod Retainer Clip (88-7-1)
  • Surface Rust On Chassis Components:Removal Procedure (88-6-6)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • Keyless Entry System New Diagnosis (87-18-6)
  • No Keyless Entry System AUTOLOCK - Reconnect Switch (87-16-2)
  • Power Moon Roof New Motor/R & I (87-18-87)
  • Theft Prevention Standard: Parts Identification No. (86-18-2)
• Automatic Trans
  • MERCON ATF Is Being Replaced By MERCON V ATF As A Service Fluid (06-14-4)
  • E4OD/4R100 - Fluid In-Line Filter Kit (00-3-8)
  • Transmission Flush/Fill Tool Available From Rotunda (99-15-2)
  • Transmission Fluid Usage Chart (98-8-8)
  • 4R44E/5R55E Trans - New Service Center Support (98-1-12)
  • Torque Converter Slip/DTC 628 Or P0741 In Memory (97-22-4)
  • Torque Converter Replacement - Cooling SYS. Cleaning (96-26-12)
  • Torque Converter Leak Test Procedure - New Tool (96-24-9)
  • New Rotunda Fluid Changer - Service Tip (95-16-10)
  • AOD Transmission No 3-4 Upshift Or Slipping 4TH Gear (93-23-18)
  • AOD Thrust Bearing Noise/Crank Wear - Flywheel Bolts (92-18-6)
  • Adhesives & Sealants - Availability & Usage (89-12-2)
  • AOD Trans Case Replacement - Bolt Modifications (89-9-12)
  • 2.3L Eng A4LD Trans Buzzing - New Shift Cable (88-8-10)
  • AOD Trans 1-2 Slip/3-2 Bump - Clutch Friction Plates (88-7-12)
  • A4LD Poor 3-4/4-3 Shift - New Solenoid/Sleeve/Screen (88-2-11)
  • AOD/A4LD Shift Cable Locks In "P" - Selector/Bracket (87-23-7)
  • AOD Transmission New Overdrive Band Anchor Pin (87-22-13)
  • A4LD Transmission New Front Oil Pump Bolts (87-21-6)
  • A/T Cooler Line Connections Leak - Modify Connectors (87-18-13)
  • New ATF Applications Chart (87-18-14)
  • A4LD Trans Leaks/Burnt Fluid/Eng Stall/Erratic Shift (87-2-15)
  • A4LD Transmission Overhaul Tips (87-2-16)
  • Approved Adhesives & Sealants For Eng/Trans/Steering (89-6T-7)
• Auxiliary Emission Control Systems
  • EEC-IV Pinpoint Test KA Revision - KOER 34 Check (93-26B-15)
  • EXH Gas Oxygen Sensor Silicone Sealer Contamination (93-23-6)
  • SBDS Damage From Tach Wire In VIP/Self-Test Connect0 (93-20-4)
  • 5.0L Eng No/Hard Start/Stalls In Below Freezing Temp (91-11-5)
  • Electronic Control Modules - Damage From Arc Welding (91-7-5)
  • No Start/Low Battery/Fuel Pump Noise - Pump Relay (90-18-3)
  • Rough Idle - Air By Pass Valve Replacement Part (89-24-4)
  • TPS Service Replacement Chart (89-16-4)
  • Throttle Position Sensor Screw Removal (89-14-7)
  • 2.3L Turbo False Mil Operation - Fuel Injectors/ECM (89-4-4)
  • EEC IV Eng & 2.3L/2.5L HSC CFI Map/Bap Sensor Applications Chart (89-1-12)
  • 3.8L Eng Bucks/Jerks When Accelerating - Map Sensor (88-23-9)
  • 5.0L Low Oil Pressure - Oil Screen/Cover/PCV Valve (88-5-10)
  • Poor DRIVEABILITY - Fuel Injector Diagnosis/Cleaning (88-17-11)
  • Electronic Modules - Damage From Static Electricity (88-13-3)
  • 5.0L Eng Low Oil Press Light - Oil Pick-Up Tube Clog (88-5-10)
  • 2.3L Turbo Poor Performance - Oil In Air Vane Meter (88-3-11)
  • High Idle/Codes 23,53,63 - Throttle Position Sensor (87-25-7)
  • 3.8L Surge/Buck When Warm/DECEL - New Erg Solenoid (87-10-15)
  • 3.8L Eng Stall/Rough Idle/Rich - Engine Ground Strap (87-17-6)
  • 5.0L Eng PCV Valve Replacement Interval (87-14-11)
  • EFI Rough Idle/Injector Terminals Loose - Diagnosis (87-13-6)
  • 2.3L EFI Turbo Burning Oil/Knock/Rough Idle/Stall (87-11-18)
  • ECM Processor Warranty Decal Information (87-11-13)
  • 2.3L Turbo M/T Low Power At Wot - New ECM (87-9-10)
  • 3.8/4.9/5.0L No Start/Miss/Rough Idle - New TPS (87-8-11)
  • 3.8L CFI New EGR Valve/Vacuum Harness Modification (87-7-15)
  • 5.0L SEFI Consumes Oil - PCV Baffle/Oil Plug/Seals (87-7-12)
  • Wiring System Testing Caution - Modify Probe Tips (87-2-5)
  • 2.3L Turbo False KOEO Code 83 Verification (86-23-10)
  • 2.3/2.5L Eng New Map/Bap Sensor Application Table (89-1T-19)
  • 2.3L Eng No Power/Boost - MISROUTED Boost Cont Hose (86-24-19)
  • Injector Tester/Cleaner Tool Maintenance Info (89-15-3)
  • Throttle Position Sensor POZIDRIVE Mount Screw Info (89-7T-9)
• Blowers, Superchargers & Turbochargers
  • 2.3/2.5/5.0L Accessory Belt TENSIONER Service Tips (87-5-16)
  • V-Ribbed Drive Belt Cracking - Normal Wear Condition (87-1-8)
• Body Interior
  • Electrical Diode Identification And Replacements (96-24-6)
  • Temp. Gauge Reads Low - Obsolete Temperature Sender (95-13-2)
  • A/C Chemical Smell - Clutch Cycling Pressure Switch (91-11-8)
  • Latches - Door - Replacement Required (91-8-4)
  • Air Conditioning Odor Treatment - Service Procedure (89-25B-1)
  • Poor A/C - Clutch Pressure Cycling Switch Diagnosis (89-14-10)
  • Inaccurate Speedo Readings - Mechanical & Electronic (89-2-7)
  • "Popping" Noise From Speakers: Suppression Capacitor (88-20-5)
  • EATC Illumination Changes W/ Turn SIGS - New EATC (88-18-2)
  • Manual Vent Windows - Glass Sticks To Weatherstrip (88-14-1)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • A/C Clutch Pressure Cycling Switch Diagnostic (89-7T-19)
• Brakes Control Systems
  • Brakes - Roughness Concern During Brake Application (95-6-2)
  • False Abs Light - High Tension Ignition Wire Routing (87-17-4)
  • Abs Module Testing Caution (87-12-3)
  • Abs Testing - New Super Star Testing Procedure (87-2-8)
  • Abs Code 61 Diagnosis - Memory Self Clears (86-25-8)
• Charging Systems
  • Generator Harness Connector Damage - Loose Contact (96-21-4)
  • 2.3L Turbo New Alternator Integral Regulator Wiring (87-10-6)
  • 2.3/2.5/5.0L Accessory Belt TENSIONER Service Tips (87-5-16)
  • V-Ribbed Drive Belt Cracking - Normal Wear Condition (87-1-8)
• Clutch
  • Asbestos Brake & Clutch Warnings (83-22-1)
• Cooling Fan
  • Cooling System - Use Of Recycled Engine Coolant (90-4-10)
• Cooling System (Mechanical)
  • Leaks Oil - New Silicone Gasket & Sealant (98-7-4)
  • Use Of Recycled Engine Coolant - Service Tip (95-18-2)
  • 2.3L Leaks Oil: Revised Cylinder Head Gasket & Bolts (94-6-4)
  • Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
  • Hesitation/Stall At Idle - Intake Manifold Gasket (90-23-6)
  • 2.3L Eng Hesitate/Stall At Idle - Intake Gasket (90-23-6)
  • Cooling System - Use Of Recycled Engine Coolant (90-4-10)
  • Adhesives & Sealants - Availability & Usage (89-12-2)
  • 2.3L Turbo Poor Performance - Oil In Air Vane Meter (88-3-11)
  • Revised Electric Fuel Pump Testing (87-11-15)
  • 2.3L Turbo Electro-Drive Cooling Fan New Service (87-7-4)
  • Fuel Stabilizer During Extended Vehicle Storage (86-13-20)
  • Diagnostic Tips For Heater Core Leaks (85-5-2)
  • Approved Adhesives & Sealants For Eng/Trans/Steering (89-6T-7)
• Cruise Control Systems
  • Cruise Control Abnormal - Grease Electrical Contacts (89-3-4)
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
• Differentials & Drive Axles
  • Adhesives & Sealants - Availability & Usage (89-12-2)
• Electronic Steering
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Steering Pull/Drift - New Wheel Alignment Specs (87-4-10)
• Electronic Suspension
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Steering Pull/Drift - New Wheel Alignment Specs (87-4-10)
• Engine Control Systems
  • Volatility Related DRIVEABILITY Concerns Service Tip (98-26-2)
  • MOTORCRAFT Fuel Injector Cleaning System (94-8-9)
  • Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
  • SBDS Damage From Tach Wire In VIP/Self-Test Connect0 (93-20-4)
  • Fuel Injectors Clogged - New Fuel Injector Cleaning (91-19-3)
  • 5.0L Eng No/Hard Start/Stalls In Below Freezing Temp (91-11-5)
  • Electronic Control Modules - Damage From Arc Welding (91-7-5)
  • No Start/Low Battery/Fuel Pump Noise - Pump Relay (90-18-3)
  • Rough Idle - Air By Pass Valve Replacement Part (89-24-4)
  • TPS Service Replacement Chart (89-16-4)
  • Throttle Position Sensor Screw Removal (89-14-7)
  • 2.3L Turbo False Mil Operation - Fuel Injectors/ECM (89-4-4)
  • EEC IV Eng & 2.3L/2.5L HSC CFI Map/Bap Sensor Applications Chart (89-1-12)
  • 3.8L Eng Bucks/Jerks When Accelerating - Map Sensor (88-23-9)
  • Poor DRIVEABILITY - Fuel Injector Diagnosis/Cleaning (88-17-11)
  • Electronic Modules - Damage From Static Electricity (88-13-3)
  • High Idle/Codes 23,53,63 - Throttle Position Sensor (87-25-7)
  • 3.8L Surge/Buck When Warm/DECEL - New Erg Solenoid (87-10-15)
  • 3.8L Eng Stall/Rough Idle/Rich - Engine Ground Strap (87-17-6)
  • EFI Rough Idle/Injector Terminals Loose - Diagnosis (87-13-6)
  • 2.3L EFI Turbo Burning Oil/Knock/Rough Idle/Stall (87-11-18)
  • ECM Processor Warranty Decal Information (87-11-13)
  • 2.3L Turbo M/T Low Power At Wot - New ECM (87-9-10)
  • 3.8/4.9/5.0L No Start/Miss/Rough Idle - New TPS (87-8-11)
  • Fuel Line Spring Lock Coupling R & R (87-3-8)
  • Wiring System Testing Caution - Modify Probe Tips (87-2-5)
  • 2.3L Turbo False KOEO Code 83 Verification (86-23-10)
  • 2.3/2.5L Eng New Map/Bap Sensor Application Table (89-1T-19)
  • 2.3L Eng No Power/Boost - MISROUTED Boost Cont Hose (86-24-19)
  • Injector Tester/Cleaner Tool Maintenance Info (89-15-3)
  • Throttle Position Sensor POZIDRIVE Mount Screw Info (89-7T-9)
• Entertainment Systems
  • No Crank - Low State Of Battery Charge (91-10-8)
  • "Popping" Noise From Speakers: Suppression Capacitor (88-20-5)
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
  • Distortion From Speakers - Poor Contact At Amplifier (89-15-8)
• Exterior Body Panels
  • Lower Body Stone Protection Repair Tips (90-15-3)
  • Treating Cosmetic Paint Damage From AIRBORN Material (89-13-3)
  • Manual Vent Windows - Glass Sticks To Weatherstrip (88-14-1)
  • Surface Rust On Chassis Components:Removal Procedure (88-6-6)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • Theft Prevention Standard: Parts Identification No. (86-18-2)
• Exterior Lights
  • Latches - Door - Replacement Required (91-8-4)
  • Electronic Instrument Cluster Display Dim/Blank (90-23-9)
  • False Lamp Out Warnings - Trailer Lighting Install. (88-2-6)
  • Electronic Dashboard Halogen Bulb Replacement (87-20-11)
  • Moisture Inside Taillight Lens - Seal Body Joint (87-18-8)
  • Moisture Inside Headlight Lens - Diagnosis/Repair (87-13-4)
• Frames, Subframes & Crossmembers
  • Bumper ISOLATER And Bracket Replacement Guidelines (94-8-1)
  • Bumper Cover - Improved Repair Materials (93-24-1)
  • Lower Body Stone Protection Repair Tips (90-15-3)
  • Treating Cosmetic Paint Damage From AIRBORN Material (89-13-3)
  • Surface Rust On Chassis Components:Removal Procedure (88-6-6)
  • Front Fascia License Plate Bracket Installation (86-22-1)
  • Theft Prevention Standard: Parts Identification No. (86-18-2)
• Front Suspension
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Suspension Stabilizer Bar Noise - New Bushings (88-4-10)
  • Suspension/Tire Alignment Specifications (87-20-16)
  • Suspension Springs Application Charts (87-18-9)
  • Steering Pull/Drift - New Wheel Alignment Specs (87-4-10)
• Fuel System
  • Volatility Related DRIVEABILITY Concerns Service Tip (98-26-2)
  • CALIFORNIA Reformulated Gasoline - Service Tip (96-10-7)
  • MOTORCRAFT Fuel Injector Cleaning System (94-8-9)
  • Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
  • Fuel Injectors Clogged - New Fuel Injector Cleaning (91-19-3)
  • Inaccurate Speedo Readings - Mechanical & Electronic (89-2-7)
  • CFI Fuel Injector Contamination - Replace Injector (87-17-5)
  • Fuel Line Spring Lock Coupling R & R (87-3-8)
• Fuses & Circuit Breakers
  • Wiring - Wire Harness Terminal Repair Kit (99-6-3)
  • Electrical Diode Identification And Replacements (96-24-6)
  • Generator Harness Connector Damage - Loose Contact (96-21-4)
  • No Crank - Low State Of Battery Charge (91-10-8)
  • Wire Harness Terminal & Connector Service Kit (89-19-5)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • New Micro-Pin Terminal Connectors Locking/Unlocking (87-7-7)
  • Wiring System Diagnosis Cautions (87-4-8)
  • Engine Compartment - Use Waterproof Wire Connectors (87-2-6)
  • Wiring Diagram Symbols Explanation (85-11-5)
• Gauges & Instrument Panels
  • Temp. Gauge Reads Low - Obsolete Temperature Sender (95-13-2)
  • EATC Display Dim Or Blank - Burned Out Bulbs (93-23-13)
  • SPEEDOMTR Modules/Cluster-PSOM Replacement Available (93-12-9)
  • New Digital Speedometer With Preset Odometer (91-8-14)
  • Electronic Instrument Cluster Display Dim/Blank (90-23-9)
  • Fuel Tank Sending Unit Wiring Damaged - New Wiring (89-14-6)
  • Electronic Fuel Gauge Wrong - Filler Pipe Position (89-6-5)
  • Inaccurate Speedo Readings - Mechanical & Electronic (89-2-7)
  • 5.0L Eng Low Oil Press Light - Oil Pick-Up Tube Clog (88-5-10)
  • False Lamp Out Warnings - Trailer Lighting Install. (88-2-6)
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
  • Electronic Dashboard Halogen Bulb Replacement (87-20-11)
  • Damaged Fuel Tank Sending Unit Connector Repair (89-7T-14)
  • New In Car Fuel Sender Test Procedure (86-15-5)
• General Servicing
  • A/C System Service - List Of Bulletins To Reference (96-15-6)
• Hazardous Waste Material
  • Primed Sheet Metal Prep Procedure & MSDS Information (94-23-4)
  • Asbestos Brake & Clutch Warnings (83-22-1)
• Headlights
  • Electronic Instrument Cluster Display Dim/Blank (90-23-9)
  • False Lamp Out Warnings - Trailer Lighting Install. (88-2-6)
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
  • Electronic Dashboard Halogen Bulb Replacement (87-20-11)
  • Moisture Inside Taillight Lens - Seal Body Joint (87-18-8)
  • Moisture Inside Headlight Lens - Diagnosis/Repair (87-13-4)
• Heated Glass/Defoggers
  • New Rear Defogger Service Kit (93-26-1)
• HVAC Control Systems
  • Climate Control - Repeat Heater Core Failure (01-15-6)
  • Filtering Refrigerant After Compressor Replacement (98-12-5)
  • Identification Of Non-Ford Approved Refrigerants (99-19-6)
  • A/C - R-12 To R-134A Retrofit Kit - Factory A/C Only (98-4-8)
  • Use Of R-12 Refrigerant Substitutes (96-17-10)
  • A/C System Service - List Of Bulletins To Reference (96-15-6)
  • Ford Approved Flushing Procedures For A/C System (95-8-1)
  • A/C "O" Ring Removal From Spring Lock Coupling (95-2-2)
  • R-12 Refrigerant Substitutes - Service Tip (94-14-3)
  • Service Parts Return Of Obsolete A/C Discharge Hoses (94-13-9)
  • Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
  • EATC Display Dim Or Blank - Burned Out Bulbs (93-23-13)
  • Service Parts Return Of Obsolete A/C Filter Kits (93-22-6)
  • Use Of Correct Fluorescent Tracer Dye - Service Tip (93-20-6)
  • A/C SLC Refrigerant Fittings Cleaning/New O-Ring Kit (93-6-5)
  • New Refrigerant Fitting "O" Rings (91-22-5)
  • A/C Chemical Smell - Clutch Cycling Pressure Switch (91-11-8)
  • Air Conditioning - Refrigerant R-12 - Service Tips (91-9-7)
  • Electronic Control Modules - Damage From Arc Welding (91-7-5)
  • A/C "O" Ring Usage Table (90-14-8)
  • Service Tips For Redesigned A/C Control Head Replace (91-11-7)
  • Air Conditioning Odor Treatment - Service Procedure (89-25B-1)
  • Poor A/C - Clutch Pressure Cycling Switch Diagnosis (89-14-10)
  • 2.3L Turbo Buzz Behind GLOVEBOX - Fresh/RECIRC Door (88-25-3)
  • A/C Drier - Replace When Major Component Serviced (88-25-5)
  • Electronic Modules - Damage From Static Electricity (88-13-3)
  • New A/C Blower Motor Wheel R & R (88-3-6)
  • A/C Low Side Pressure Hose Service Adapter Tool (87-7-2)
  • Diagnostic Tips For Heater Core Leaks (85-5-2)
  • A/C Clutch Pressure Cycling Switch Diagnostic (89-7T-19)
• Identification
  • Corporate Standard Circuit Nos. & Wire Color Codes (87-15-3)
  • Production/Build Date Stamp Relocation (87-10-3)
  • 1.9/3.0/3.8L Engine Serial Number Location (87-1-9)
• Ignition Switch/Steering Lock
  • Instrument Cluster Warning Lights Dimly Lit (93-24-10)
  • No Crank - Low State Of Battery Charge (91-10-8)
  • Latches - Door - Replacement Required (91-8-4)
  • New Ignition Switch Replacement Procedure (89-10T-5)
  • Ignition Key Warning Switch New R & I (89-19-2)
  • Door Lock/Ignition 5/10 Bit Key Systems Information (87-24-2)
• Ignition System
  • Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
  • New Idle Air By-Pass Kit & ECA Relearn Procedure (91-7-4)
  • Poor Cold Start/Idle/Run - Fuel Recommendations (91-8-13)
  • New Ignition Switch Replacement Procedure (89-10T-5)
  • Distributor Gear Matched To Distributor At Assembly (89-6-11)
  • Hard/No Start - TFI Module Connection (88-20-9)
  • TFI Module/Pip Sensor New EEC-IV Testing (87-21-10)
  • 2.0/2.3/2.5/3.0/3.8/5.0/5.8L Eng Short IGN Coil (87-20-18)
  • 2.3L Turbo Surge/Miss/Low Power - Turbo Outlet Hose (87-18-16)
  • Revised Electric Fuel Pump Testing (87-11-15)
  • TFI Stall/No Start - TFI Module Diagnosis/Sealing (87-6-10)
  • 2.3L Eng Knock/Oil Consumption - New Oil Dipstick (87-5-20)
  • New Distributor Drive Gear Removal Tool (87-2-18)
  • Fuel Stabilizer During Extended Vehicle Storage (86-13-20)
• Infotainment
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
• Interior/Exterior Trim
  • Treating Cosmetic Paint Damage From AIRBORN Material (89-13-3)
  • Manual Vent Windows - Glass Sticks To Weatherstrip (88-14-1)
  • Adhesive BODYSIDE Mouldings & Nameplates Replacement (88-10-4)
  • Surface Rust On Chassis Components:Removal Procedure (88-6-6)
  • Front Fender Moulding Missing Attaching Nuts (87-4-3)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • Improved Lower Sound Insulator Panels Availability (87-21-1)
  • Power Moon Roof New Motor/R & I (87-18-87)
  • Windshield A-Pillar Molding Click - New Molding (87-5-2)
  • Interior Trim: Recommended Clean-Up Tips (87-2-3)
  • Front Fascia License Plate Bracket Installation (86-22-1)
  • Adhesive-Backed Name Plate/Emblem Loose: Replacement (86-20-1)
• Interior/Illumination Lights
  • EATC Display Dim Or Blank - Burned Out Bulbs (93-23-13)
  • Electronic Instrument Cluster Display Dim/Blank (90-23-9)
  • False Lamp Out Warnings - Trailer Lighting Install. (88-2-6)
  • Electronic Dashboard Halogen Bulb Replacement (87-20-11)
  • Moisture Inside Taillight Lens - Seal Body Joint (87-18-8)
  • Moisture Inside Headlight Lens - Diagnosis/Repair (87-13-4)
• Lubrication System
  • Leaks Oil - New Silicone Gasket & Sealant (98-7-4)
  • 2.3L Leaks Oil: Revised Cylinder Head Gasket & Bolts (94-6-4)
  • Hesitation/Stall At Idle - Intake Manifold Gasket (90-23-6)
  • 2.3L Eng Hesitate/Stall At Idle - Intake Gasket (90-23-6)
  • Adhesives & Sealants - Availability & Usage (89-12-2)
  • Oil Consumption Information (89-9-10)
  • 2.3L Turbo Poor Performance - Oil In Air Vane Meter (88-3-11)
  • Revised Electric Fuel Pump Testing (87-11-15)
  • Reading Oil Dipstick Fill Marks/Proper Oil Filling (87-9-5)
  • Fuel Stabilizer During Extended Vehicle Storage (86-13-20)
  • Approved Adhesives & Sealants For Eng/Trans/Steering (89-6T-7)
  • Normal Oil Consumption Information (89-5T-13)
• Manual Steering
  • Revised Torque Requirement For New Tie Rods (96-1-1)
  • Adhesives & Sealants - Availability & Usage (89-12-2)
• Manual Trans
  • MERCON ATF Is Being Replaced By MERCON V As A Service Fluid For Some Manual Transmissions (06-26-1)
  • Adhesives & Sealants - Availability & Usage (89-12-2)
  • 2.3L Turbo Gearshift Rattle - New Extension Assembly (87-13-11)
  • Approved Adhesives & Sealants For Eng/Trans/Steering (89-6T-7)
• Mechanical
  • Leaks Oil - New Silicone Gasket & Sealant (98-7-4)
  • 2.3L Leaks Oil: Revised Cylinder Head Gasket & Bolts (94-6-4)
  • Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
  • 2.3L Eng Timing Belt Warble Noise - New Style Belt (92-5-11)
  • AOD Thrust Bearing Noise/Crank Wear - Flywheel Bolts (92-18-6)
  • New Idle Air By-Pass Kit & ECA Relearn Procedure (91-7-4)
  • 5.0L Eng AOD Trans Metal To Metal Engine Noise (91-4-10)
  • Poor Cold Start/Idle/Run - Fuel Recommendations (91-8-13)
  • Hesitation/Stall At Idle - Intake Manifold Gasket (90-23-6)
  • 2.3L Eng Hesitate/Stall At Idle - Intake Gasket (90-23-6)
  • 5.0L Eng Excess Oil Consumption - Inspection/Repair (90-1-9)
  • Adhesives & Sealants - Availability & Usage (89-12-2)
  • Oil Consumption Information (89-9-10)
  • 3.8L Engine Mount Service Parts Applications/Usage (89-5-12)
  • Oil Dipstick Level Markings Unclear - Reading Marks (88-8-9)
  • 5.0L Eng Low Oil Press Light - Oil Pick-Up Tube Clog (88-5-10)
  • 2.3L Turbo Poor Performance - Oil In Air Vane Meter (88-3-11)
  • 2.3L Turbo Surge/Miss/Low Power - Turbo Outlet Hose (87-18-16)
  • 5.0L Eng Knock - Main Bearing Clearance Adjustment (87-11-12)
  • Revised Electric Fuel Pump Testing (87-11-15)
  • 5.0L SEFI Consumes Oil - PCV Baffle/Oil Plug/Seals (87-7-12)
  • 2.3L Eng Knock/Oil Consumption - New Oil Dipstick (87-5-20)
  • 1.9/3.0/3.8L Engine Serial Number Location (87-1-9)
  • Fuel Stabilizer During Extended Vehicle Storage (86-13-20)
  • Approved Adhesives & Sealants For Eng/Trans/Steering (89-6T-7)
  • Normal Oil Consumption Information (89-5T-13)
• Mechanical - Hydraulic
  • Silicone Brake Caliper Grease Requirement (98-5A-13)
  • Wheels - Proper Lug Torque Procedures - Service Tip (98-5A-4)
  • Brakes - Roughness Concern During Brake Application (95-6-2)
  • Occasional Or Intermittent Brake Squeal - Normal (90-22-6)
  • Brake Shudder/Rotor Damage - Torque LUGNUTS Manually (90-19-9)
  • Asbestos Brake & Clutch Warnings (83-22-1)
• Mirrors
  • Various Vehicles - Rear-View Mirror Concern Analysis (23-7092)
  • Power Window Regulator Counterbalance Spring R & R (91-19-5)
  • Seat Memory Diagnostic Testing Procedures (89-5-3)
  • Power Door Locks Inoperative - Rod Retainer Clip (88-7-1)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • Memory Seat Self-Testing (87-17-2)
  • Door Locks Activated By Courtesy Light Switch - OK (87-1-7)
  • New Procedure To Diagnose Memory Seat Sensor (89-12A-2)
• Paint & Coatings
  • Urethane Mounted Glass Material Usage Procedure (95-12-1)
  • Paint Iron Particle Removal/Acid Rain Neutralization (95-6-1)
  • Primed Sheet Metal Prep Procedure & MSDS Information (94-23-4)
  • Exterior CLEARCOAT MICROCHECKING, Hazing Or Peeling (93-8-4)
  • Exterior Paint Comprehensive Repair Procedures (91-18-1)
  • Lower Body Stone Protection Repair Tips (90-15-3)
  • Treating Cosmetic Paint Damage From AIRBORN Material (89-13-3)
  • Stronger Adhesive Vinyl Tape Stripes Availability (87-24-3)
  • Difficulty Matching Production Paint Colors (87-15-1)
  • Surface Rust On Chassis Components:Removal Procedure (88-6-6)
  • Power Moon Roof Noise/Leak - New Seal Assembly (88-3-2)
  • Styled Wheel Ornament Retention Information (87-16-9)
  • Repainting Peeling Paint Stripes (87-10-2)
  • 1987 Color Chart Supplier Cross-Reference List (87-1-2)
  • Adhesive-Backed Name Plate/Emblem Loose: Replacement (86-20-1)
• Passive Restraints
  • Latches - Door - Replacement Required (91-8-4)
  • Safety Belt Tongue Cover Parts Availability (88-25-2)
  • Safety Belt - Replacement Procedure After Accident (88-15-3)
• Procedures
  • Vehicle Storage: Maintenance Tips (88-9-9)
• Rear Suspension
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Suspension Stabilizer Bar Noise - New Bushings (88-4-10)
  • Suspension/Tire Alignment Specifications (87-20-16)
  • Suspension Springs Application Charts (87-18-9)
  • Steering Pull/Drift - New Wheel Alignment Specs (87-4-10)
• Schedule
  • 5.0L Eng PCV Valve Replacement Interval (87-14-11)
• Seats
  • Leather Seat Cleaning Procedure - Service Tip (98-17-1)
  • Power Window Regulator Counterbalance Spring R & R (91-19-5)
  • Power Seat Slow/No Movement - Lubricate Seat Track (90-19-5)
  • Seat Memory Diagnostic Testing Procedures (89-5-3)
  • Safety Belt Tongue Cover Parts Availability (88-25-2)
  • Safety Belt - Replacement Procedure After Accident (88-15-3)
  • Power Door Locks Inoperative - Rod Retainer Clip (88-7-1)
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • Memory Seat Self-Testing (87-17-2)
  • Hood Hinge Squeak/Rattle - Hinge Adjustment (87-5-1)
  • Door Locks Activated By Courtesy Light Switch - OK (87-1-7)
  • New Procedure To Diagnose Memory Seat Sensor (89-12A-2)
• Sleeper
  • Latches - Door - Replacement Required (91-8-4)
  • Manual Vent Windows - Glass Sticks To Weatherstrip (88-14-1)
• Solar Ventilation
  • A/C Drier - Replace When Major Component Serviced (88-25-5)
• Starter
  • New Idle Air By-Pass Kit & ECA Relearn Procedure (91-7-4)
  • No Crank - Low State Of Battery Charge (91-10-8)
  • No Start/Low Battery/Fuel Pump Noise - Pump Relay (90-18-3)
  • 2.3L Turbo Surge/Miss/Low Power - Turbo Outlet Hose (87-18-16)
  • Revised Electric Fuel Pump Testing (87-11-15)
  • Fuel Stabilizer During Extended Vehicle Storage (86-13-20)
• Steering Column
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Clunk Noise Loose Steering - Loose Tilt Column Shaft (88-4-9)
  • Steering Pull/Drift - New Wheel Alignment Specs (87-4-10)
• Steering Column Switches
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
• Steering Control Systems
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Electronic Control Modules - Damage From Arc Welding (91-7-5)
  • Electronic Modules - Damage From Static Electricity (88-13-3)
• Steering Gear
  • Revised Torque Requirement For New Tie Rods (96-1-1)
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Adhesives & Sealants - Availability & Usage (89-12-2)
  • Approved Adhesives & Sealants For Eng/Trans/Steering (89-6T-7)
• Steering Linkage
  • Revised Torque Requirement For New Tie Rods (96-1-1)
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Steering Pull/Drift - New Wheel Alignment Specs (87-4-10)
  • Approved Adhesives & Sealants For Eng/Trans/Steering (89-6T-7)
• Sun Roof/T-Top/Convertible Top
  • Treating Cosmetic Paint Damage From AIRBORN Material (89-13-3)
  • Stronger Adhesive Vinyl Tape Stripes Availability (87-24-3)
  • Manual Vent Windows - Glass Sticks To Weatherstrip (88-14-1)
  • Surface Rust On Chassis Components:Removal Procedure (88-6-6)
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
  • Styled Wheel Ornament Retention Information (87-16-9)
  • Repainting Peeling Paint Stripes (87-10-2)
  • Power Moon Roof New Motor/R & I (87-18-87)
  • Hood Hinge Squeak/Rattle - Hinge Adjustment (87-5-1)
  • Adhesive-Backed Name Plate/Emblem Loose: Replacement (86-20-1)
• Suspension Control Systems
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Electronic Control Modules - Damage From Arc Welding (91-7-5)
  • Electronic Modules - Damage From Static Electricity (88-13-3)
• System
  • Volatility Related DRIVEABILITY Concerns Service Tip (98-26-2)
  • Leaks Oil - New Silicone Gasket & Sealant (98-7-4)
  • CALIFORNIA Reformulated Gasoline - Service Tip (96-10-7)
  • MOTORCRAFT Fuel Injector Cleaning System (94-8-9)
  • 2.3L Leaks Oil: Revised Cylinder Head Gasket & Bolts (94-6-4)
  • EEC-IV Pinpoint Test KA Revision - KOER 34 Check (93-26B-15)
  • Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
  • EXH Gas Oxygen Sensor Silicone Sealer Contamination (93-23-6)
  • SBDS Damage From Tach Wire In VIP/Self-Test Connect0 (93-20-4)
  • New Idle Air By-Pass Kit & ECA Relearn Procedure (91-7-4)
  • Fuel Injectors Clogged - New Fuel Injector Cleaning (91-19-3)
  • 5.0L Eng No/Hard Start/Stalls In Below Freezing Temp (91-11-5)
  • No Crank - Low State Of Battery Charge (91-10-8)
  • Poor Cold Start/Idle/Run - Fuel Recommendations (91-8-13)
  • Electronic Control Modules - Damage From Arc Welding (91-7-5)
  • Hesitation/Stall At Idle - Intake Manifold Gasket (90-23-6)
  • 2.3L Eng Hesitate/Stall At Idle - Intake Gasket (90-23-6)
  • No Start/Low Battery/Fuel Pump Noise - Pump Relay (90-18-3)
  • Rough Idle - Air By Pass Valve Replacement Part (89-24-4)
  • New Ignition Switch Replacement Procedure (89-10T-5)
  • TPS Service Replacement Chart (89-16-4)
  • Throttle Position Sensor Screw Removal (89-14-7)
  • Adhesives & Sealants - Availability & Usage (89-12-2)
  • Distributor Gear Matched To Distributor At Assembly (89-6-11)
  • 2.3L Turbo False Mil Operation - Fuel Injectors/ECM (89-4-4)
  • EEC IV Eng & 2.3L/2.5L HSC CFI Map/Bap Sensor Applications Chart (89-1-12)
  • 3.8L Eng Bucks/Jerks When Accelerating - Map Sensor (88-23-9)
  • Hard/No Start - TFI Module Connection (88-20-9)
  • 5.0L Low Oil Pressure - Oil Screen/Cover/PCV Valve (88-5-10)
  • Poor DRIVEABILITY - Fuel Injector Diagnosis/Cleaning (88-17-11)
  • Electronic Modules - Damage From Static Electricity (88-13-3)
  • 5.0L Eng Low Oil Press Light - Oil Pick-Up Tube Clog (88-5-10)
  • 2.3L Turbo Poor Performance - Oil In Air Vane Meter (88-3-11)
  • High Idle/Codes 23,53,63 - Throttle Position Sensor (87-25-7)
  • TFI Module/Pip Sensor New EEC-IV Testing (87-21-10)
  • 2.0/2.3/2.5/3.0/3.8/5.0/5.8L Eng Short IGN Coil (87-20-18)
  • 3.8L Surge/Buck When Warm/DECEL - New Erg Solenoid (87-10-15)
  • 2.3L Turbo Surge/Miss/Low Power - Turbo Outlet Hose (87-18-16)
  • 3.8L Eng Stall/Rough Idle/Rich - Engine Ground Strap (87-17-6)
  • CFI Fuel Injector Contamination - Replace Injector (87-17-5)
  • 5.0L Eng PCV Valve Replacement Interval (87-14-11)
  • EFI Rough Idle/Injector Terminals Loose - Diagnosis (87-13-6)
  • 2.3L EFI Turbo Burning Oil/Knock/Rough Idle/Stall (87-11-18)
  • ECM Processor Warranty Decal Information (87-11-13)
  • Revised Electric Fuel Pump Testing (87-11-15)
  • 2.3L Turbo M/T Low Power At Wot - New ECM (87-9-10)
  • 3.8/4.9/5.0L No Start/Miss/Rough Idle - New TPS (87-8-11)
  • 3.8L CFI New EGR Valve/Vacuum Harness Modification (87-7-15)
  • 5.0L SEFI Consumes Oil - PCV Baffle/Oil Plug/Seals (87-7-12)
  • TFI Stall/No Start - TFI Module Diagnosis/Sealing (87-6-10)
  • 2.3L Eng Knock/Oil Consumption - New Oil Dipstick (87-5-20)
  • Fuel Line Spring Lock Coupling R & R (87-3-8)
  • New Distributor Drive Gear Removal Tool (87-2-18)
  • Wiring System Testing Caution - Modify Probe Tips (87-2-5)
  • 2.3L Turbo False KOEO Code 83 Verification (86-23-10)
  • Fuel Stabilizer During Extended Vehicle Storage (86-13-20)
  • 2.3/2.5L Eng New Map/Bap Sensor Application Table (89-1T-19)
  • 2.3L Eng No Power/Boost - MISROUTED Boost Cont Hose (86-24-19)
  • Approved Adhesives & Sealants For Eng/Trans/Steering (89-6T-7)
  • Injector Tester/Cleaner Tool Maintenance Info (89-15-3)
  • Throttle Position Sensor POZIDRIVE Mount Screw Info (89-7T-9)
• Towing
  • A4LD Trans Leaks/Burnt Fluid/Eng Stall/Erratic Shift (87-2-15)
• Transfer Case
  • Adhesives & Sealants - Availability & Usage (89-12-2)
  • A4LD Trans Leaks/Burnt Fluid/Eng Stall/Erratic Shift (87-2-15)
• Transmission Control Systems
  • Torque Converter Slip/DTC 628 Or P0741 In Memory (97-22-4)
  • AOD Transmission No 3-4 Upshift Or Slipping 4TH Gear (93-23-18)
  • No Crank - Low State Of Battery Charge (91-10-8)
  • Electronic Control Modules - Damage From Arc Welding (91-7-5)
• Vacuum Pumps/Lines/Tanks/Water Trap
  • Leaks Oil - New Silicone Gasket & Sealant (98-7-4)
  • 2.3L Leaks Oil: Revised Cylinder Head Gasket & Bolts (94-6-4)
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
  • 2.3L Turbo Surge/Miss/Low Power - Turbo Outlet Hose (87-18-16)
• Wheel Alignment
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Steering Pull/Drift - New Wheel Alignment Specs (87-4-10)
• Wheels & Tire System
  • Wheels - Proper Lug Torque Procedures - Service Tip (98-5A-4)
  • Tire Company Phone Numbers For Customer Assistance (98-5-2)
  • Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
  • Brake Shudder/Rotor Damage - Torque LUGNUTS Manually (90-19-9)
  • Wheel Weights/Aluminum Rims (90-13-2)
  • Aluminum Rims Leak Air - Inspection/Hot Melt Sealant (89-17-3)
  • Styled Wheel Ornament Retention Information (87-16-9)
  • Aluminum Wheel Vibration/Shake - Balance Weights (87-14-7)
  • Alum Wheel Leaks Air - Hot Melt Wheel Repair Info (89-9T-6)
  • Aluminum Wheel Air Leak - Use Hot Melt-Stick On Leak (89-9T-6)
• Window Motors & Regulators
  • Windshield And Interior Glass - Fog/Film (96-22-1)
  • Urethane Mounted Glass Material Usage Procedure (95-12-1)
  • "Iridescence" Or "Mottling" In Tempered Glass (93-21-1)
  • Power Window Regulator Counterbalance Spring R & R (91-19-5)
  • Seat Memory Diagnostic Testing Procedures (89-5-3)
  • "Popping" Noise From Speakers: Suppression Capacitor (88-20-5)
  • Stronger Adhesive Vinyl Tape Stripes Availability (87-24-3)
  • Manual Vent Windows - Glass Sticks To Weatherstrip (88-14-1)
  • Power Door Locks Inoperative - Rod Retainer Clip (88-7-1)
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • Memory Seat Self-Testing (87-17-2)
  • Styled Wheel Ornament Retention Information (87-16-9)
  • Repainting Peeling Paint Stripes (87-10-2)
  • Power Moon Roof New Motor/R & I (87-18-87)
  • Hood Hinge Squeak/Rattle - Hinge Adjustment (87-5-1)
  • Windshield A-Pillar Molding Click - New Molding (87-5-2)
  • Door Locks Activated By Courtesy Light Switch - OK (87-1-7)
  • Adhesive-Backed Name Plate/Emblem Loose: Replacement (86-20-1)
  • New Procedure To Diagnose Memory Seat Sensor (89-12A-2)
  • Revised Windshield Installation Procedures (89-6T-4)
• Wiper/Washer Systems
  • Sound Distortion From ETR Radio: Rework Wire Harness (87-3-4)
• Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.)
  • Wiring - Wire Harness Terminal Repair Kit (99-6-3)
  • Electrical Diode Identification And Replacements (96-24-6)
  • Generator Harness Connector Damage - Loose Contact (96-21-4)
  • Temp. Gauge Reads Low - Obsolete Temperature Sender (95-13-2)
  • No Crank - Low State Of Battery Charge (91-10-8)
  • Wire Harness Terminal & Connector Service Kit (89-19-5)
  • Inaccurate Speedo Readings - Mechanical & Electronic (89-2-7)
  • INOPERATVE Power Door Lock - Modify Relay Bracket (87-24-7)
  • New Micro-Pin Terminal Connectors Locking/Unlocking (87-7-7)
  • Wiring System Diagnosis Cautions (87-4-8)
  • Engine Compartment - Use Waterproof Wire Connectors (87-2-6)
  • Wiring Diagram Symbols Explanation (85-11-5)