Instrument Panel Cluster (IPC)
INSTRUMENT PANEL CLUSTER (IPC) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B10D5:13 | PATS Antenna: Circuit Open | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10D7:05 | PATS Key: System Programming Failure | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10D7:51 | PATS Key: Not Programmed | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10D7:87 | PATS Key: Missing Message | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10D7:8F | PATS Key: Erratic | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10D8:00 | PATS Key Less Than Minimum Programmed: No Sub-Type Information | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10D9:87 | PATS Transponder: Missing Message | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10DA:51 | PATS PCM Identifier: Not Programmed | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10DA:61 | PATS PCM Identifier: Signal Calculation Failure | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B10DA:86 | PATS PCM Identifier: Signal Invalid | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| B1218:44 | Transmitter Identification Code: Data Memory Failure | REFER to HANDLES, LOCKS, LATCHES & KEYLESS ENTRY SYSTEM article. |
| B1218:51 | Transmitter Identification Code: Not Programmed | REFER to HANDLES, LOCKS, LATCHES & KEYLESS ENTRY SYSTEM article. |
| B1218:81 | Transmitter Identification Code: Invalid Serial Data Received | REFER to HANDLES, LOCKS, LATCHES & KEYLESS ENTRY SYSTEM article. |
| B1A75:11 | Fuel Sender No. 1: Circuit Short to Ground | GO to PINPOINT TEST B . |
| B1A75:15 | Fuel Sender No. 1: Circuit Short to Battery or Open | GO to PINPOINT TEST B . |
| B1A76:11 | Fuel Sender No. 2 : Circuit Short to Ground | GO to PINPOINT TEST B . |
| B1A76:15 | Fuel Sender No. 2: Circuit Short to Battery or Open | GO to PINPOINT TEST B . |
| B1A82:11 | External Trip Switch: Circuit Short to Ground | GO to PINPOINT TEST AI . |
| B1A82:13 | External Trip Switch: Circuit Open | GO to PINPOINT TEST AI . |
| B1A82:23 | External Trip Switch: Signal Stuck Low | GO to PINPOINT TEST AI . |
| P062F:44 | Internal Control Module EEPROM Error: Data Memory Failure | CLEAR the DTCs. REPEAT the self-test. If the DTC is still present, INSTALL a new IPC . REFER to INSTRUMENT PANEL CLUSTER (IPC) in this service information. TEST the system for normal operation. |
| P1534:14 | Restraint Deployment Indicator Circuit: Open or Short to Ground | INSTALL a new IPC . REFER to INSTRUMENT PANEL CLUSTER (IPC) in this service information. |
| U0100:00 | Lost Communication with ECM /PCM "A": No Sub Type Information | REFER to ANTI-THEFT SYSTEM - PASSIVE ANTI-THEFT SYSTEM (PATS) article. |
| U0100:87 | Lost Communication with ECM /PCM "A": Missing Message | GO to PINPOINT TEST AQ . |
| U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) control module: Missing Message | GO to PINPOINT TEST AR . |
| U0131:87 | Lost Communication With Power Steering Control Module: Missing Message | GO to PINPOINT TEST AS . |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to PINPOINT TEST AT . |
| U0142:87 | Lost Communication With Body Control Module "B": Missing Message | GO to PINPOINT TEST AU . |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to PINPOINT TEST AV . |
| U0161:87 | Lost Communication With Compass Module: Missing Message | REFER to ELECTRONIC COMPASS article. |
| U0161:92 | Lost Communication With Compass Module: Performance or Incorrect Operation | REFER to ELECTRONIC COMPASS article. |
| U0164:87 | Lost Communication With HVAC Control Module: Missing Message | GO to PINPOINT TEST AW . |
| U0184:87 | Lost Communication With Radio: Missing Message | GO to PINPOINT TEST AX . |
| U0401:68 | Invalid Data Received from the ECM /PCM A: Event Information | This DTC is set when the IPC receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0422:86 | Invalid Data Received from the Body Control Module: Signal Invalid | This DTC is set when the IPC receives invalid network data from the Smart Junction Box (SJB) with a faulted Tire Pressure Monitoring System (TPMS) input. RETRIEVE and REPAIR all non-network DTCs in the SJB and other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U2100:55 | Initial Configuration Not Complete: Not Configured | CARRY OUT the Programmable Module Installation (PMI) procedure for the IPC . REFER to MODULE COMMUNICATIONS NETWORK - MODULE CONFIGURATION article. |
| U2101:56 | Control Module Configuration Incompatible: Invalid/Incompatible Configuration | The IPC and SJB configuration do not match. If either an IPC or SJB was installed, CARRY OUT the PMI for the suspect module. REFER to MODULE COMMUNICATIONS NETWORK - MODULE CONFIGURATION article. CLEAR the DTCs. REPEAT the self-test. |
| U3000:45 | Control Module: Program Memory Failure | INSTALL a new IPC . REFER to INSTRUMENT PANEL CLUSTER (IPC) in this service information. TEST the system for normal operation. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AY . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AZ . |
| U300A:94 | Ignition Switch: Unexpected Operation | GO to PINPOINT TEST BA . |