HVAC Module DTC Table
HVAC MODULE DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description | Action to Take |
|---|---|---|
| B1081:00 | Left Temperature Damper Motor: No Sub Type Information | GO to PINPOINT TEST O . |
| B1081:11 | Left Temperature Damper Motor: Circuit Short to Ground | GO to PINPOINT TEST O . |
| B1081:12 | Left Temperature Damper Motor: Circuit Short to Battery | GO to PINPOINT TEST O . |
| B1082:00 | Right Temperature Damper Motor: No Sub Type Information | GO to PINPOINT TEST O . |
| B1082:11 | Right Temperature Damper Motor: Circuit Short to Ground | GO to PINPOINT TEST O . |
| B1082:12 | Right Temperature Damper Motor: Circuit Short to Battery | GO to PINPOINT TEST O . |
| B1083:11 | Recirculation Damper Motor: Circuit Short to Ground | GO to PINPOINT TEST I . |
| B1083:12 | Recirculation Damper Motor: Circuit Short to Battery | GO to PINPOINT TEST I . |
| B1083:13 | Recirculation Damper Motor: Circuit Open | GO to PINPOINT TEST I . |
| B1086:00 | Air Distribution Damper Motor: No Sub Type Information | GO to PINPOINT TEST J . |
| B1086:11 | Air Distribution Damper Motor: Circuit Short to Ground | GO to PINPOINT TEST J . |
| B1086:12 | Air Distribution Damper Motor: Circuit Short to Battery | GO to PINPOINT TEST J . |
| B10AF:11 | Blower Fan Relay: Circuit Short to Ground | GO to PINPOINT TEST Q . |
| B10AF:12 | Blower Fan Relay: Circuit Short to Battery | GO to PINPOINT TEST P . |
| B10AF:13 | Blower Fan Relay: Circuit Open | GO to PINPOINT TEST P . |
| B10B8:63 | Push Buttons: Circuit/Component Protection Time-Out | A button held too long sets this DTC. Attempt to CLEAN the buttons. CLEAR the DTCs. REPEAT the self-test. If code returns, INSTALL a new HVAC module. REFER to CLIMATE CONTROL . TEST the system for normal operation. |
| B10B9:12 | Blower Control: Circuit Short to Battery | GO to PINPOINT TEST Q . |
| B10B9:14 | Blower Control: Circuit Short to Ground or Open | GO to PINPOINT TEST P . |
| B11E5:11 | Left HVAC Damper Position Sensor: Circuit Short to Ground | GO to PINPOINT TEST O . |
| B11E5:15 | Left HVAC Damper Position Sensor: Circuit Short to Battery or Open | GO to PINPOINT TEST O . |
| B11E6:11 | Right HVAC Damper Position Sensor: Circuit Short to Ground | GO to PINPOINT TEST O . |
| B11E6:15 | Right HVAC Damper Position Sensor: Circuit Short to Battery or Open | GO to PINPOINT TEST O . |
| B11E7:11 | Air Distribution Damper Position Sensor: Circuit Short to Ground | GO to PINPOINT TEST J . |
| B11E7:15 | Air Distribution Damper Position Sensor: Circuit Short to Battery or Open | GO to PINPOINT TEST J . |
| B1A61:11 | Cabin Temperature Sensor: Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1A61:15 | Cabin Temperature Sensor: Circuit Short to Battery or Open | GO to PINPOINT TEST D . |
| B1A63:11 | Right Solar Sensor: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A63:15 | Right Solar Sensor: Circuit Short to Battery or Open | GO to PINPOINT TEST E . |
| B1A64:11 | Left Solar Sensor: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A64:15 | Left Solar Sensor: Circuit Short to Battery or Open | GO to PINPOINT TEST E . |
| B1B71:11 | Evaporator Temperature Sensor: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1B71:15 | Evaporator Temperature Sensor: Circuit Short to Battery or Open | GO to PINPOINT TEST F . |
| B1C83:11 | Rear Defog Relay: Circuit Short to Ground | REFER to REAR VIEW MIRRORS . |
| B1C83:12 | Rear Defog Relay: Circuit Short to Battery | REFER to REAR VIEW MIRRORS . |
| B1C83:13 | Rear Defog Relay: Circuit Open | REFER to REAR VIEW MIRRORS . |
| C1B14:11 | Sensor Supply Voltage A: Circuit Short to Ground | GO to PINPOINT TEST C . |
| C1B14:12 | Sensor Supply Voltage A: Circuit Short to Battery | GO to PINPOINT TEST C . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | This DTC can set because the Body Control Module (BCM) is unable to communicate with the HVAC module over the Controller Area Network (CAN) bus. CARRY OUT a self-test of the BCM. If the scan tool indicates that the BCM is not responding, REFER to MODULE COMMUNICATIONS NETWORK to diagnose the network communication concern. If BCM DTCs are present, REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U0401:09 | Invalid Data Received From ECM/PCM A: Component Failure | This DTC can set due to a fault in the PCM. CARRY OUT a self-test of the PCM. If the scan tool indicates that the PCM is not responding, REFER to MODULE COMMUNICATIONS NETWORK to diagnose the network communication concern. If PCM DTCs are present, REFER to ELECTRONIC ENGINE CONTROLS - GASOLINE ENGINES -- F250-F550 SUPER DUTY or ELECTRONIC ENGINE CONTROLS - DIESEL ENGINE -- F250-F550 SUPER DUTY . |
| U0401:68 | Invalid Data Received From ECM/PCM A: Event Information | This DTC can set due to a fault in the PCM. CARRY OUT a self-test of the PCM. If the scan tool indicates that the PCM is not responding, REFER to MODULE COMMUNICATIONS NETWORK to diagnose the network communication concern. If PCM DTCs are present, REFER to ELECTRONIC ENGINE CONTROLS - GASOLINE ENGINES -- F250-F550 SUPER DUTY or ELECTRONIC ENGINE CONTROLS - DIESEL ENGINE -- F250-F550 SUPER DUTY . |
| U0401:81 | Invalid Data Received From ECM/PCM A: Invalid Serial Data Received | This DTC can set due to a fault in the PCM. CARRY OUT a self-test of the PCM. If the scan tool indicates that the PCM is not responding, REFER to MODULE COMMUNICATIONS NETWORK to diagnose the network communication concern. If PCM DTCs are present, REFER to ELECTRONIC ENGINE CONTROLS - GASOLINE ENGINES -- F250-F550 SUPER DUTY or ELECTRONIC ENGINE CONTROLS - DIESEL ENGINE -- F250-F550 SUPER DUTY . |
| U0401:82 | Invalid Data Received From ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updates | This DTC can set due to a fault in the PCM. CARRY OUT a self-test of the PCM. If the scan tool indicates that the PCM is not responding, REFER to MODULE COMMUNICATIONS NETWORK to diagnose the network communication concern. If PCM DTCs are present, REFER to ELECTRONIC ENGINE CONTROLS - GASOLINE ENGINES -- F250-F550 SUPER DUTY or ELECTRONIC ENGINE CONTROLS - DIESEL ENGINE -- F250-F550 SUPER DUTY . |
| U0422:68 | Invalid Data Received From Body Control Module: Event Information | This DTC can set due to a fault in the Body Control Module (BCM). CARRY OUT a self-test of the BCM. If the scan tool indicates that the BCM is not responding, REFER to MODULE COMMUNICATIONS NETWORK to diagnose the network communication concern. If BCM DTCs are present, REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U0422:81 | Invalid Data Received From Body Control Module: Invalid Serial Data Received | This DTC can set due to a fault in the Body Control Module (BCM). CARRY OUT a self-test of the BCM. If the scan tool indicates that the BCM is not responding, REFER to MODULE COMMUNICATIONS NETWORK to diagnose the network communication concern. If BCM DTCs are present, REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CARRY OUT Programmable Module Installation (PMI) on the HVAC module. REFER to MODULE CONFIGURATION . REPEAT the self-test. If PMI is successful, the DTC will not be present. If the DTC returns, INSTALL a new HVAC module. REFER to CLIMATE CONTROL . TEST the system for normal operation. |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | CARRY OUT Programmable Module Installation (PMI) on the HVAC module. REFER to MODULE CONFIGURATION . REPEAT the self-test. If PMI is successful, the DTC will not be present. If the DTC returns, INSTALL a new HVAC module. REFER to CLIMATE CONTROL . TEST the system for normal operation. |
| U3000:41 | Control Module: General Checksum Failure | INSTALL a new HVAC module. REFER to CLIMATE CONTROL . TEST the system for normal operation. |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | CARRY OUT Programmable Module Installation (PMI) on the HVAC module. REFER to MODULE CONFIGURATION . REPEAT the self-test. If PMI is successful, the DTC will not be present. If the DTC returns, INSTALL a new HVAC module. REFER to CLIMATE CONTROL . TEST the system for normal operation. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST G . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST G . |