FixVault

Torque Specification

WARNING: This page is about a different variant/trim than selected.
TORQUE SPECIFICATION

Description Nm lb-ft lb-in
A/C compressor fitting nut 15 - 133
A/C compressor stud bolts 25 18 -
Accessory drive belt tensioner bolt 48 35 -
Camshaft bearing cap bolts (1) - - -
Camshaft bearing mega cap bolts(1) - - -
CMP  sensor bolt 10 - 89
Catalytic convertor-to-exhaust manifold nuts 40 30 -
Clutch pressure plate(1) - - -
Connecting rod cap bolts(1) - - -
Coolant outlet bolts 10 - 89
Coolant outlet pipe bolt 10 - 89
Coolant pump bolts 20 - 177
Coolant pump pulley bolts 20 - 177
Cooling fan assembly nut and bolt 9 - 80
Crankshaft main bearing cap bolts(1) - - -
CKP  sensor bolt 10 - 89
Crankshaft pulley bolt(1) - - -
Crankshaft rear seal retainer plate bolts(1) - - -
Cylinder head bolts(1) - - -
CHT  sensor 11 - 97
Engine front cover bolts(1) - - -
Engine oil filter (2) - - -
EOP (3) - - -
Engine shields 7 - 62
Engine support insulator bolts 55 41 -
Engine support insulator bracket bolts and stud bolts 55 41 -
Engine support insulator nuts 63 46 -
Engine-to-transmission bolts and stud bolts 48 35 -
Exhaust H-pipe clamp nuts 48 35 -
Exhaust manifold nuts(1) - - -
Exhaust manifold studs 25 18 -
Flexplate(1) - - -
Flexplate inspection cover bolts 35 26 -
Flywheel(1) - - -
Front crossmember brace 48 35 -
Fuel rail bolts(1) - - -
Generator B+ wire terminal nut 17 - 150
Generator bolt and nut 48 35 -
Ground strap-to-cowl bolt 10 - 89
Ground strap-to-RH engine support insulator nut 48 35 -
Heater hose support nuts 7 - 62
Hood bolts 12 - 106
Ignition coil-on-plug bolt 6 - 53
Intake manifold assembly bolts(1) - - -
Knock Sensor (KS) 20 - 177
Lower underbody shield bolts 10 - 89
Oil cooler threaded fitting 58 43 -
Oil filter adapter bolts(1) - - -
Oil pan bolts(1) - - -
Oil pan drain plug 26 19 -
Oil pan stud bolts(1) - - -
Oil pan stud bolt bolt-to-wiring harness bracket nut 8 - 71
Oil pump bolts and stud bolts(1) - - -
Oil pump screen and pickup tube bolts(1) - - -
Oil pump screen and pickup tube spacer 25 18 -
Primary timing chain tensioner bolts 10 - 89
Spark plugs 15 - 133
Steering column dash boot nuts 9 - 80
Steering intermediate shaft bolt 47 35 -
Strut tower cross brace 35 26 -
Subframe nuts and bolts 115 85 -
Thermostat housing bolts 10 - 89
Timing chain guide bolts 10 - 89
Torque converter nuts 40 30 -
Transmission fluid cooler tube bracket-to-flexplate inspection cover stud bolt nut 13 - 115
Transmission fluid cooler tube bracket-to-RH engine support insulator bracket stud bolt nut 48 35 -
Transmission fluid cooler tube clamp-to-fan shroud bolt 8 - 71
Underbody shield bolt 10 - 89
Valve cover bolts(1) - - -
VCT  assembly bolts(1) - - -
(1) Refer to the procedure in this service information.
(2) Do not lubricate O-ring seal, tighten to 16 Nm (142 lb-in).
(3) Tighten to 14 Nm (124 lb-in) plus an additional 180 degrees.