Common Specifications & Procedures
RANGER COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | Specifications | |||
| Torque: | Refer to the appropriate component in Removal And Installation | |||
| Axle Nut/Hub Nut | N/A | |||
| Battery | Specifications | |||
| Brakes | ||||
| Bleeding Sequence | Brake System Pressure Bleeding | |||
| Front Disc Brakes w/Torque | Refer to appropriate component in Removal And Installation | |||
| Rear Disc Brakes w/Torque | Refer to appropriate component in Removal And Installation | |||
| Charging | ||||
| Generator w/Torque | ||||
| 2.3L EcoBoost (201kW/273PS) | For removal and installation, refer to Generator - 2.3L Ecoboost (201KW/273PS) Lower Generator Bolt: 18 lb.ft (25 Nm) Generator Nut: 18 lb.ft (25 Nm) |
|||
| Drive Belts | ||||
| Adjustment | Accessory Drive | |||
| Belt Routing | Accessory Drive - Component Location . | |||
| Engine Cooling | ||||
| General Service Specifications | Specifications | |||
| Radiator Cap Pressure | 145 kPa (21 psi) | |||
| Thermostat R & I | Thermostat . | |||
| Water Pump R & I | Coolant Pump | |||
| Engine Mechanical | ||||
| Compression | Specifications | |||
| Oil pressure (hot @ 2, 000 rpm) | 29 -60 psi (200 -414 kPa) | |||
| Overhaul | Specifications | |||
| Torque: | Refer to appropriate component in Removal And Installation | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | ||||
| 2.3L EcoBoost (201kW/273PS) | For tightening sequence, refer to Flexplate
. Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm) |
|||
| Fuel System | ||||
| Fuel Filter Location | Located in fuel tank as part of the fuel pump module. | |||
| Fuel Filter R & I | Fuel Pump And Sender Unit | |||
| Pressure Release Procedure | Fuel System Pressure Release | |||
| Fuel Pressure Test Procedure | Fuel System Pressure Check | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | 1-3-4-2 FIRING ORDER & CYLINDER IDENTIFICATION |
|||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | |||
| Spark Plug | ||||
| 2.3L EcoBoost (201kW/273PS) | ||||
| Type | CYFS 12Y PT | |||
| Gap | 0.030 in (.75 mm) | |||
| Torque: | 106 lb.in (12 Nm) | |||
| Starting | ||||
| Starter | Specifications | |||
| Torque: | ||||
| For removal and installation, refer to Starter Motor . | Starter Motor Studbolts: 35 lb.ft (47.5 Nm) | |||
| Wheel Alignment | ||||
| Adjustment Specifications | Specifications | |||
| Torque: | Refer to the appropriate procedure in General Procedures | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | For tightening sequence, refer to Wheel And Tire
. 135 Nm |
|||