FixVault
Home › Ford › 2022 › Explorer ST, 4WD › Repair and Diagnosis › Engine Performance › Fuel Delivery › Fuel System - General Information - 3.0L ECOBOOST › General Procedures › Quick Release Coupling

Quick Release Coupling

For information on Ford Color Coded Illustrations refer to OEM COLOR CODING

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 1 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660698Courtesy of FORD MOTOR COMPANY
  4. GFD660699Courtesy of FORD MOTOR COMPANY

Connect 

  1. Push the quick release coupling onto the tube.
    GFD660700Courtesy of FORD MOTOR COMPANY
  2. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    Press the retainer clip into the quick release coupling body until flush and the tabs are locked in place.

    GFD660701Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 2 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660702Courtesy of FORD MOTOR COMPANY
  4. GFD660703Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660704Courtesy of FORD MOTOR COMPANY
  2. GFD660705Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 3 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660706Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660707Courtesy of FORD MOTOR COMPANY
  2. GFD660708Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 4 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660709Courtesy of FORD MOTOR COMPANY
  4. GFD660710Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660711Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 5 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660712Courtesy of FORD MOTOR COMPANY
  4. GFD660713Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660714Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 6 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. Press the tabs of the rear retainer clip and pull it to the outward position.
    GFD660715Courtesy of FORD MOTOR COMPANY
  4. GFD660716Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick release coupling to make sure it is securely fastened.
    GFD660717Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 7 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660718Courtesy of FORD MOTOR COMPANY
  4. GFD660719Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick connect coupling to make sure it is securely fastened.
    GFD660720Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 8 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660712Courtesy of FORD MOTOR COMPANY
  4. GFD660713Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660714Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 9 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
    1. Release the secondary locking tab.
    2. Depress the primary locking tab.
    3. Separate the quick release coupling from the tube.
    GFD660721Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Lock the secondary locking tab.

    GFD660722Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 10 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
    1. Push on the locking tab.
    2. Lift the clip.
    GFD660723Courtesy of FORD MOTOR COMPANY
    1. Depress the tabs inward.
    2. Push the clip downward.
    3. Separate the quick release coupling from the fuel line.
    GFD660724Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. Push the clip down into the quick release coupling.
    3. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD660725Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 11 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660771Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660771Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 12 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660727Courtesy of FORD MOTOR COMPANY
  4. GFD660728Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660729Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 13 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660730Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660731Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 14 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660732Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660733Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 15 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Press both retaining tabs inward and remove quick release coupling from fuel tube.
    GFD660734Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Inspect and clean both quick release coupling ends.

    Install the quick release coupling onto the tube until it is fully seated.

    GFD660735Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 16 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660736Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660736Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 17 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660737Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660738Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 18 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660739Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660740Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 19 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660741Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660742Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 20 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660743Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660744Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 21 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660745Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660746Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 22 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660747Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660748Courtesy of FORD MOTOR COMPANY
  2. GFD660749Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  3. NOTE: Make sure that all fuel connections are checked for leaks.
    NOTE: This step is only necessary if a new component is installed.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD660750Courtesy of FORD MOTOR COMPANY
  4. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 23 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660751Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD660752Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 24 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660753Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660754Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 25 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
    1. Depress the clip into the quick release coupling.
    2. Separate the quick release coupling from the tube.
    GFD660755Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660756Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 26 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
    1. Remove the quick release coupling from the tube.
    GFD660757Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660758Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 27 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to Battery Disconnect and Connect .
  3. GFD660759Courtesy of FORD MOTOR COMPANY
  4. Remove the quick release coupling from the tube.
    GFD660760Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD660761Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Disconnect and Connect .
About FixVault