FixVault
Home › GMC › 2007 › Acadia SLE, AWD › Repair and Diagnosis › External Pages › Different car › Section 50 (Sunroof System) › Repair Instructions › Sunroof Module Assembly Replacement (C3Y) › Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2005 Pontiac G6. However, it is still accessible from the selected car via links, so may be relevant.
  1. Hold the sunshade up on end to expose the set spring cam hole, turn the cam 14 times in the counterclock position to set.
  2. Insert a suitable tool in the cam hole to lock in place.
  3. Install the sunroof window seal to the sunroof module. Refer to Sunroof Window Seal Replacement (C3Y)  or Sunroof Window Seal Replacement (CF5) .
  4. Install the sunroof sunshade motor. Refer to Sunroof Sunshade Motor/Actuator Replacement .
  5. Install the sunroof module motor. Refer to Sunroof Motor/Actuator Replacement (C3Y)  or Sunroof Motor/Actuator Replacement (CF5) .
  6. Install the sunshade. Refer to Sunroof Sunshade Panel Replacement (C3Y)  or Sunroof Sunshade Panel Replacement (CF5) .
  7. Install the sunroof module through the roof opening.
    8. Fig 1: View Of Four Corner Screws
    GM1564614Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
    IMPORTANT: Do NOT remove the four corner screws until last. Do NOT remove the nut just the TORX™ bit screws (1), the nut is used for height adjustment.
  8. Install the corner screws (1), with the aid of an assistant.

    Tighten:  Tighten the bolts to 10 N.m (89 lb in).

    9. Fig 2: View Of Sunroof Module To Roof Ring Bolts
    GM1564610Courtesy of GENERAL MOTORS CORP.
  9. Install the bolts (1) that secure the sunroof module to the roof ring.

    Tighten:  Tighten the bolts to 10 N.m (89 lb in).

    10. Fig 3: View Of Sunroof Module Rear Bolts
    GM1564607Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: The shade must be closed to expose the bolts (1) holes.
  10. Install the bolts (2) in the rear of the sunroof module first, then install bolts (1).

    Tighten:  Tighten the bolts to 10 N.m (89 lb in).

  11. Connect the front and rear sunroof drain hoses from the drain spigot located in each corner.
  12. Connect the electrical connectors to the motors.
  13. Install the headliner. Refer to Headliner Replacement in Interior Trim.
  14. Install the sunroof finishing lace. Refer to Sunroof Finishing Lace Replacement (CF5)  or Sunroof Finishing Lace Replacement (C3Y) .
  15. Cycle the sunroof window to the fully vent position.
  16. Install the front sunroof window. Refer to Sunroof Window Replacement - Front .
  17. Install the 2nd or 3rd sunroof window. Refer to Sunroof Window Replacement - 2-3 .
  18. Install the rear sunroof window. Refer to Sunroof Window Replacement - Rear .
  19. Sunroof module adjustment. Refer to Sunroof Module Adjustment .
  20. Perform the Initialization/Teach procedure. Refer to Sunroof Motor/Actuator Initilization/Teach Process (Panoramic)  or Sunroof Motor/Actuator Initilization/Teach Process (New Motor)  or Sunroof Motor/Actuator Initilization/Teach Process (Existing Motor) .
  21. Inspect the sunroof for proper operation.
  22. Close the sunshade.
About FixVault