FixVault
Home › Hummer › 2008 › H3 Base, Automatic › Repair and Diagnosis › External Pages › Different car › Section 366 (Frame And Underbody) › Repair Instructions › Front Frame Replacement › Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2009 Cadillac STS. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install the engine support fixture. Refer to the following procedures:
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  3. Remove the front wheels. Refer to Tire and Wheel Removal and Installation .
  4. Remove the front air deflector. Refer to Front Air Deflector Replacement .
    5. Fig 1: Identifying Engine Harness-To-Frame Electrical Harness Retainers
    GM708192Courtesy of GENERAL MOTORS CORP.
  5. Disconnect the electrical harness retainers (1) securing the engine harness to the frame.
    6. Fig 2: Identifying Left Rearward Retainer
    GM708204Courtesy of GENERAL MOTORS CORP.
  6. Disconnect the left rearward retainer (1).
    7. Fig 3: Identifying Right Rearward Retainer
    GM708197Courtesy of GENERAL MOTORS CORP.
  7. Disconnect the right rearward retainer (1).
    8. Fig 4: Identifying Anti-Lock Brake Wiring Harness At Lower Control Arms
    GM802031Courtesy of GENERAL MOTORS CORP.
  8. Disconnect the antilock brake wiring harness from the lower control arms.
    9. Fig 5: Identifying Brake Line Bracket Nut
    GM819185Courtesy of GENERAL MOTORS CORP.
  9. Loosen the brake line bracket nut (1).
  10. Disconnect the brake lines from the frame.
    11. Fig 6: View Of Mechanics Wire, Front Inner Energy Absorber Bracket Bolt
    GM708709Courtesy of GENERAL MOTORS CORP.
  11. Using mechanics wire (3), support the radiator and AC condenser assembly to the front inner energy absorber bracket bolt (1).
    12. Fig 7: Identifying Washer Bottle Bracket Nuts & Bracket
    GM708714Courtesy of GENERAL MOTORS CORP.
  12. Remove the washer bottle bracket nuts and bracket (3).
  13. Loosen the brake pressure modulator valve (BPMV) nuts (1) in order to separate the BPMV (2) from the bracket assembly.
    14. Fig 8: View Of Stabilizer Shaft Mounting Bolts
    GM814811Courtesy of GENERAL MOTORS CORP.
    NOTE: Mark the stabilizer shaft to ensure the correct position when reinstalling.
  14. Loosen the stabilizer shaft mounting bolts.
    15. Fig 9: View Of Lower Stabilizer Shaft Link Retaining Nut
    GM750841Courtesy of GENERAL MOTORS CORP.
  15. Remove the lower stabilizer shaft link retaining nut.
  16. Remove the stabilizer shaft link from the lower control arm.
    17. Fig 10: Locating Power Steering Pressure Hose Retaining Nut
    GM802037Courtesy of GENERAL MOTORS CORP.
  17. Remove the power steering pressure hose retaining nut from the air conditioning compressor.
  18. Position power steering pressure hose aside.
    19. Fig 11: Locating Power Steering Gear Mounting Bolts
    GM802792Courtesy of GENERAL MOTORS CORP.
  19. Remove the power steering gear mounting bolts.
    20. Fig 12: Identifying Mechanics Wire Supporting Power Steering Gear
    GM708719Courtesy of GENERAL MOTORS CORP.
  20. Using mechanics wire (4), support the power steering gear (3) to the bolt bracket installed in the oil pan.
    21. Fig 13: View Of Outer Tie Rod-To-Steering Knuckle And Retaining Nut
    GM794579Courtesy of GENERAL MOTORS CORP.
  21. Remove the outer tie rod retaining nut.
    22. Fig 14: View Of Outer Tie Rod Assembly & J 24319-B
    GM643351Courtesy of GENERAL MOTORS CORP.
  22. Using J 24319-B  , remove the outer tie rod. See Special Tools .
    23. Fig 15: View of Lower Shock Bolts
    GM742959Courtesy of GENERAL MOTORS CORP.
  23. Remove the lower shock bolts (1).
    24. NOTE: The brake calipers do not need to be removed from the knuckle assembly.
  24. Disconnect the lower ball joint from the steering knuckle and position the knuckle assembly away from the lower control arms. Refer to Lower Control Arm Replacement (AWD) or Lower Control Arm Replacement (RWD) .
    25. Fig 16: Identifying Engine Mounts Lower Retaining Nuts
    GM708183Courtesy of GENERAL MOTORS CORP.
  25. Remove the engine mounts lower retaining nuts (2).
    26. Fig 17: Identifying Frame Mounting Bolts
    GM822362Courtesy of GENERAL MOTORS CORP.
  26. Install the J 39580  . See Special Tools .
  27. Lower the vehicle to the frame support table.
  28. Remove the frame mounting bolts (2).
  29. With the aid of an assistant, carefully raise the body from the frame.
  30. Ensure when raising the body, the following items are clear from the frame:
    • The brake pipes
    • The steering knuckle assembly
    • The wheel speed sensor (WSS) electrical harness
    31. Fig 18: Identifying Frame Removed From Support Fixture
    GM819203Courtesy of GENERAL MOTORS CORP.
  31. Remove the lower control arms. Refer to Lower Control Arm Replacement (AWD) or Lower Control Arm Replacement (RWD) .
  32. Remove the stabilizer shaft. Refer to Stabilizer Shaft Replacement .
  33. With the aid of an assistant, remove the frame from the support fixture.
About FixVault