FixVault

Torque Specifications

WARNING: This page is about a different car, the 2004 Hyundai Santa Fe and 2003 Hyundai Santa Fe. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application Ft. Lbs (N.m)
Auto Tensioner Fixed Bolt 15-20 (20-27)
Camshaft Bearing Cap
Inner (1)
Outer 14-15 (19-20)
Camshaft Sprocket Bolt 59-81 (80-110)
Connecting Rod Nut
Step 1 26 (35)
Step 2 Tighten An Additional 90 Degrees
Coolant Inlet Fitting Bolt 13-15 (17-20)
Coolant Pump Bolt
M8 Bolt Head Mark "7" 11-16 (15-22)
M10 24-37 (33-50)
Coolant Temperature Sensor 15-30 (20-40)
Crankshaft Bolt 133-140 (180-190)
Cylinder Head Bolt (Cold) (2) 77-85 (105-115)
Drive Plate & Adapter Plate Bolt 54-57 (73-77)
Drive Belt Pulley Bolt 26-41 (35-55)
Engine Hanger Bracket Bolt 20-28 (27-38)
Engine Mounting Fasteners
Engine Mounting Bracket Bolt 44-59 (60-80)
Engine Mounting Bracket Nut 44-59 (60-80)
Engine Mounting Insulator Bolt 66-81 (90-110)
Front Roll Stopper Bracket-To-Transaxle Bolt 44-59 (60-80)
Front Roll Stopper Insulator Fasteners 37-48 (50-65)
Front Roll Stopper Bracket-To-Subframe Bolt 44-59 (60-80)
Rear Roll Stopper Bracket-To-Subframe Bolts 44-59 (60-80)
Rear Roll Stopper Bracket-To-Transaxle Bolts 37-48 (50-65)
Rear Roll Stopper Insulator Bolt & Nut 37-48 (50-65)
Exhaust Components
Catalytic Converter-To-Center Exhaust Pipe Nut 22-30 (30-40)
Center Exhaust Pipe-To-Main Muffler Nuts 22-30 (30-40)
Exhaust Manifold-To-Engine Bolt 30-33 (40-45)
Front Exhaust Pipe-To-Catalytic Converter Bolt 30-44 (40-60)
Front Exhaust Pipe-To-Exhaust Manifold Nuts 22-30 (30-40)
Exhaust Manifold-To-Cylinder Head Nut 30-33 (40-45)
Generator Mounting Bracket Bolt (All) 15-22 (20-30)
Intake Manifold-To-Cylinder Head Nuts 15-17 (20-23)
Main Bearing Bolt 52-59 (70-80)
Oil Drain Plug 26-33 (35-45)
Oil Filter 9-12 (12-16)
Oil Pump Case Bolt 11-15 (15-20)
Oil Pump Relief Valve Plug 30-37 (40-50)
Oil Screen Bolt 11-16 (15-22)
Oxygen Sensor 30-37 (40-50)
Power Steering Bracket-To-Cylinder Head Bolt 13-19 (17-26)
Power Steering Pump-To-Bracket bolt 13-19 (17-26)
Starter-To-Engine
Bolt 20-25 (27-34)
Nut 15-22 (20-30)
Surge Tank Stay Bolt 11-15 (15-20)
Throttle Body-To-Surge Tank Bolts 15-18 (20-25)
Transaxle Mounting Fasteners
Transaxle Mounting Bracket Bolts 44-59 (60-80)
Transaxle Mounting Sub Bracket Nut 44-59 (60-80)
Transaxle Mounting Insulator Bolt 66-81 (90-110)
Timing Belt Cover Bolt (8 mm) 15-20 (20-27)
Timing Belt Idler Pulley Bolt 37-44 (50-60)
Timing Belt Tensioner Arm Fixed Bolt 26-41 (35-55)
Timing Belt Tensioner Bolt 15-20 (20-27)
Timing Belt Tensioner Pulley Bolt 32-41 (43-55)
Upper Oil Pan Bolt
10x38 mm 22-31 (30-42)
6x18 mm (3)
6x161.55 mm (3)
6x152.5 mm (3)
Water Outlet Fitting Bolt 13-15 (17-20)
INCH Lbs. (N.m) 
Air Cleaner Body Installation Bolt 71-106 (8-12)
Air Cleaner Mounting Bolt 71-106 (8-12)
Crankshaft Position Sensor Wheel Screw 97-106 (11-12)
Cylinder Head Cover Bolt 71-88 (8-10)
Delivery Pipe Installation Bolt 89-133 (10-15)
Fuel Hose Clamp-To-Engine Bolt 106-133 (12-15)
Generator Inlet Pipe-To-Front Cylinder Head Assembly 106-133 (12-15)
Heat Protector-To-Exhaust Manifold 106-133 (12-15)
Lower Oil Pan Bolt 89-106 (10-12)
Main Muffler Hanger Support Bracket Bolt 89-133 (10-15)
Oil Level Guide-To-Engine 106-133 (12-15)
Oil Pressure Switch 71-133 (8-15)
Oil Pump Cover Screw 71-106 (8-12)
Oil Seal Case 89-106 (10-12)
Rear Plate 89-106 (10-12)
Timing Belt Cover Bolt (6 mm) 89-106 (10-12)
Transaxle Mounting Plate 89-106 (10-12)
(1) Tighten to 89-106 INCH Lbs. (10-12 N.m).
(2) Tighten cylinder head bolts in sequence. See Fig 1.
(3) Tighten to 44-62 INCH Lbs. (5-7 N.m).
Fig 1: Identifying Cylinder Head Bolt Tightening Sequence
G00240113Courtesy of HYUNDAI MOTOR CO.