Common Specs & Procedures
SANTA FE (EXCEPT HEV) COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE | ||
| Axle Nut/Hub Nut | |||
| Front | 294.2-313.8 N.m (30.0-32.0 kgf.m, 217.0-231.5 lb-ft) | ||
| Rear | 294.2-313.8 N.m (30.0-32.0 kgf.m, 217.0-231.5 lb-ft) | ||
| Battery | |||
| BATTERY | |||
| Brakes | |||
| Bleeding Sequence | Refer to BRAKE BLEEDING PROCEDURES . | ||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE . | ||
| Charging | |||
| Generator | |||
| ALTERNATOR . | |||
| Torque: | |||
| Refer to torque specs given for each component in CHARGING SYSTEM . | |||
| Drive Belts | |||
| Adjustment | Automatic tensioner | ||
| Drive Belt Routing | Refer to Drive Belt Routing figure under INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | |||
| See Cooling System in table under SPECIFICATIONS . | |||
| Radiator Cap Pressure | 13.51-17.78 psi | ||
| Thermostat R & I | Refer to INTEGRATED THERMAL MANAGEMENT MODULE (ITM) . | ||
| Water Pump R & I | Refer to WATER PUMP . | ||
| Engine Mechanical | |||
| Compression | |||
| Refer to COMPRESSION PRESSURE INSPECTION . | |||
| Oil pressure | 90.22 kPa (0.92 kgf/cm, 13.09 psi) or above @ 1000 RPM, 110°C ± 2°C (230°F ± 35.6°F) | ||
| Overhaul | |||
| SPECIFICATIONS . | |||
| Torque | |||
| TIGHTENING TORQUE . | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 127.5-137.3 N.m (94.0- 101.3 Ft. Lbs.) | ||
| Fuel System | |||
| Pressure Specification | 480-520 kPa (4.9-5.3 kgf/cm, 69.6-75.4 psi) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST . | ||
| Fuel Filter Location | Fuel filter is part of fuel pump motor. | ||
| Fuel Filter R & I | FUEL FILTER . | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 1-3-4-2: For additional information, refer to the FIRING ORDER & CYLINDER IDENTIFICATION data. | ||
| Ignition Wires (Resistance) | Coil-On | ||
| Ignition Wires (Routing) | Coil-On | ||
| Spark Plug | |||
| Type | |||
| SILZKR7K11S | |||
| Gap | |||
| 1.0 ~ 1.1 mm (0.0394 ~ 0.0433 in.) | |||
| Torque | 14.7- 24.5 N.m (1.5-2.5 kgf.m, 10.9-18.1 lb-ft) | ||
| Starting | |||
| Starter | STARTER . | ||
| Torque | 49.0-63.7 N.m (5.0-6.5 kgf.m, 36.2-47.0 lb-ft) | ||
| Wheel Alignment | |||
| Adjustment Specifications | Refer to WHEEL ALIGNMENT . | ||
| Torque | TIGHTENING TORQUE . | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 107.9-125.5 N.m (11.0-13.0 kgf.m, 79.6-94.0 lb-ft) | ||