Transaxle Specifications
BRAKE BAND
| Application | Specification |
|---|---|
| Anchor End Pin Tightening Torque | 35-52 INCH Lbs. (3.9-5.9 N.m) |
| Number Of Returning Revolutions For Anchor End Pin | 2.5 |
| Lock Nut Tightening Torque | 23-27 Ft. Lbs. (31-36 N.m) |
TRANSAXLE SPECIFICATIONS
| Application | In. (mm) | ||
|---|---|---|---|
| Differential Assembly | |||
| Side Gear-To-Case Clearance | .004-.008 (.10-.20) | ||
| Differential Side Bearing Preload | .002-.0035 (.05-.09) | ||
| Forward & Overrun Clutches | |||
| Dish Plate Thickness | .106 (2.70) | ||
| Drive Plate Thickness | .063 (1.60) | ||
| Service Limit | .055 (1.40) | ||
| Retaining Plate-To-Snap Ring | |||
| Specified Clearance (Forward Clutch) | .018-.033 (.45-.85) | ||
| Specified Clearance (Overrun Clutch) | .028-.043 (.70-1.10) | ||
| Service Limit (Forward Clutch) | .073 (1.85) | ||
| Service Limit (Overrun Clutch) | .067 (1.70) | ||
| High Clutch | |||
| Drive Plate Thickness | .063 (1.60) | ||
| Service Limit | .055 (1.40) | ||
| Retaining Plate-To-Snap Ring | |||
| Specified Clearance | .071-.087 (1.80-2.20) | ||
| Service Limit | .118 (3.00) | ||
| Input Shaft Seal Ring-To-Ring Groove | |||
| Specified Clearance | .003-.009 (.08-.23) | ||
| Service Limit | .009 (.23) | ||
| Low & Reverse Brake | |||
| Drive Plate Thickness | .071 (1.80) | ||
| Service Limit | .063 (1.60) | ||
| Retaining Plate-To-Snap Ring | |||
| Specified Clearance | .067-.083 (1.70-2.10) | ||
| Service Limit | .130 (3.30) | ||
| Oil Pump Seal Ring-To-Ring Groove | |||
| Specified Clearance | .004-.010 (.10-.25) | ||
| Service Limit | .010 (.25) | ||
| Oil Pump Side Clearance | .001-.002 (.03-.05) | ||
| Oil Pump Outer Gear-To-Housing Clearance | .004-.007 (.11-.18) | ||
| Output Shaft End Play | 0-.0059 (0-.15) | ||
| Output Shaft Seal Ring-To-Ring Groove | |||
| Specified Clearance | .004-.010 (.10-.25) | ||
| Service Limit | .010 (.25) | ||
| Pinion Washer-To-Planetary Gear | |||
| Specified Clearance | .008-.028 (.20-.70) | ||
| Service Limit | .031 (.80) | ||
| Reverse Clutch | |||
| Dish Plate Thickness | .121 (3.08) | ||
| Drive Plate Thickness | .063 (1.60) | ||
| Service Limit | .055 (1.40) | ||
| Retaining Plate-To-Snap Ring | |||
| Specified Clearance | .020-.031 (.50-.80) | ||
| Service Limit | .047 (1.20) | ||
| Reverse Clutch End Play | .022-.035 (.55-.90) | ||
| Total End Play | .010-.022 (.25-.55) | ||