Section 1 (Engine Control System (Introduction) (2.0L Turbo))
WARNING: This page is about a different variant/trim than selected.
- Precaution
- Precautions
- Notes
- Precautions When Using Power Tools (Air Or Electric) And Hammers
- Precaution For Procedure Without Cowl Top Cover
- Precautions For Removing Battery Terminal
- Precautions For Performing 2-Wheel Drive Test
- Precaution For Stop/Start System Service
- Precaution For Risk Of Explosion And Injury
- General Precautions
- Precautions
- Preparation
- System Description
- Component Parts
- Engine Control System
- Accelerator Pedal Position Sensor
- Air-Fuel Ratio (A/F) Sensor
- Intake Camshaft Position Sensor
- Coolant Pump Switchover Valve
- Coolant Thermostat Heater Element
- Cooling Fan Control Module
- Crankshaft Position Sensor
- ECM
- EMCM (Energy Management Control Module)
- Engine Restart Bypass Relay
- Engine Restart Bypass Control Relay
- FPCM (Fuel Pump Control Module)
- Fuel Injector
- Fuel Pressure Sensor
- Fuel Pump
- Full-Load Operation Vent Line Heater Element
- Hood Switch
- Knock Sensor
- Main Battery Current Sensor (With Main Battery Temperature Sensor)
- Pressure Sensor Downstream Of Air Filter
- Refrigerant Pressure Sensor
- Stop Lamp Switch & Brake Pedal Position Switch
- Stop/Start Off Switch
- Sub-Battery Relay
- Sub-Battery Current Sensor (With Sub-Battery Temperature Sensor)
- Throttle Valve Actuator
- Vacuum Sensor
- Structure And Operation
- System
- Engine Control System
- Ignition On Control
- Engine Start Control
- Rpm Control
- Smooth Running Control
- Injection Regulation Control
- Ignition System Control
- Synchronize Fuel Injection And Ignition Order Function
- Camshaft Adjustment Function
- Torque Control
- Knock Control
- Air-Fuel Mixture Ratio Control
- System Description
- System Diagram
- Description
- Effective Purge Of Exhaust Gas In The Three Way Catalyst
- Air-Fuel Mixture Ratio Corrections Closed-Loop Control
- Air Fuel Ratio Sensor Control
- Sensor Heater Control
- Air-Fuel Mixture Ratio Corrections Adjustment Control
- Shifting Of The Air-Fuel Mixture Ratio Characteristics Map
- Catalyst Monitoring Function
- System Description
- Cold Start Mixture Enrichment Control
- System Description
- Description
- Starting Mixture Enrichment Control - System Diagram
- Starting Mixture Enrichment Control - System Description
- Post-Start Enrichment Control - System Diagram
- Post-Start Enrichment Control - System Description
- Warm-Up Enrichment Control - System Diagram
- Warm-Up Enrichment Control - System Description
- System Description
- Deceleration Fuel Shutoff Control
- Charge Air Control
- Ignition Off Control
- Fuel Supply Control
- Thermal Management Control
- Exhaust Treatment Function
- Evaporative Emission System
- Stop/Start System
- System Description
- System Diagram
- Input/Output Signal Chart - ECM
- Input/Output Signal Chart - EMCM
- System Description
- Basic Operation
- Stop/Start Readiness Condition
- Stop/Start Operation Condition
- Restart Condition
- Restart Inhibit Mode
- Restart Condition (Each Selector Lever, The Brake Pedal And The Accelerator Pedal Operation) - P Position
- Restart Condition (Each Selector Lever, The Brake Pedal And The Accelerator Pedal Operation) - N Position
- Restart Condition (Each Selector Lever, The Brake Pedal And The Accelerator Pedal Operation) - D Position
- System Description
- Starter Motor Drive Control
- Engine On Energy Management Function
- Automatic Speed Control Device (ASCD)
- Fuel Filler Cap Warning System
- INFINITI Drive Mode Selector
- Information Display (Combination Meter)
- Warning/Indicator/Chime List
- Can Communication
- Operation
- Handling Precaution
- On Board Diagnostic (OBD) System
- ECM
- Diagnosis Description
- Description
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Fault Detection
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Test Procedure
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Cyclic Monitoring
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Continuous Monitoring
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Readiness Code
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Fault Storage
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Avoiding Consequential Faults
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Saving The Error Freeze Frame Data
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Fault Display
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Reading Out Fault Memory
- Function Sequence For On-Board Diagnosis (OBD) - Function Sequence For Erasing Faults
- Diagnosis Description
- EMCM
- Fuel Pump Control Module (FPCM)
- ECM
- Diagnosis System (ECM)
- Diagnosis System (FPCM)
- Diagnosis System (EMCM)
- Component Parts