FixVault
Home › Jaguar › 2007 › XK8 2D Convertible › Repair and Diagnosis › Quick Lookups › Technical Bulletins › Technical Service Bulletins › Restraints Control Systems › Restraints Control Module (RCM) Configuration (JTB00003)

Restraints Control Module (RCM) Configuration (JTB00003)

Publication date: 2006-12-21
Reference number: JTB00003

RESTRAINTS CONTROL MODULE (RCM) CONFIGURATION

RESTRAINTS CONTROL MODULE (RCM) CONFIGURATION

TECHNICAL SERVICE BULLETIN

Reference Number(s): JTB00003, Date of Issue:  December 21, 2006
JAGUAR: 2007 XK
SECTION: 501-20B - SUPPLEMENTAL RESTRAINT SYSTEM

AFFECTED VEHICLE RANGE

New XK 

VIN: All 

Model Year: 2007 

CONDITION SUMMARY

RESTRAINTS CONTROL MODULE (RCM) CONFIGURATION 

NOTE: Certain vehicles may be subject to Jaguar Service Action S856 "Software Enhancement Program" which addresses the situation noted in this bulletin. DDW should be reviewed for VIN applicability prior to proceeding with this bulletin. If S856 is applicable, complete the Service Action to resolve this concern.

Situation:  This bulletin has been released to inform Retailers that if a customer complains that the Supplementary Restraints System (SRS) light has illuminated and  DTC U0001-88 has been logged, the RCM must be configured using IDS DVD 104 Patch File 3 or later software. A CAN BUS error is causing the faults.

Action:  Should these concerns be verified and the VIN is not covered by S856, refer to the Repair Procedure detailed in this bulletin to configure the RCM, with or without a passenger seat track position sensor, using IDS.

PARTS

No parts required. Information purposes only. 

TOOLS

IDS DVD 104 with Patch File 3 (or later) software installed 

WARRANTY

NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair time.

DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.

WARRANTY INFORMATION CHART

Description SRO Time (Hours) Condition Code Causal Part
Configure the RCM 86.99.69  0.30    C2P 1902 - prior to VIN B01026
C2P 11933 - VIN B01026 to B03383
C2P 12242 - VIN B03384 onwards

Normal warranty policy and procedures apply. 

REPAIR PROCEDURE

CONFIGURE RESTRAINTS CONTROL MODULE (RCM)

NOTE: This procedure requires IDS DVD 104 with Patch File 3 or later software.
CAUTION: A Midtronics PSC-550 Vehicle Power Supply must be connected to the vehicle battery during diagnosis and module configuration.
  1. Connect the Midtronics PSC-550 power supply to the vehicle battery.
  2. Connect IDS to the vehicle and begin a new diagnostic session, by entering the correct VIN for the current vehicle.
  3. Follow all IDS on-screen prompts.
  4. When prompted 'Do you wish to read diagnostic trouble codes?', select 'NO' and then press 'tick' to continue.
  5. When the Content Model' is displayed select 'Vehicle Configuration' tab.
  6. From the 'Vehicle Configuration Menu' expand the 'Module Programming' menu.
  7. From the Module Programming Menu, expand the 'Configure New Modules' menu.
    NOTE: Beginning with VIN B03409 the passenger seat track sensor was deleted on all vehicles. Some vehicles between VIN B00001 to VIN B03408 had the passenger seat track position sensor deleted. VIN LIST  provides a list for those vehicles between VIN B00001 to VIN B03408 that DO NOT have the seat track position sensor installed.
    NOTE: IDS will prompt the user with a series of pop-up boxes as follows:
    • 'Region' - select 'North America'
    • 'Restraints occupant classification system (OCS)' -
      • up to VIN B09097 - select 'Not fitted'
      • after VIN B09097 - select 'Fitted'
    • 'Is the passenger's seat track position restraints sensor fitted' -
      • VIN between B00001 to VIN B03408 NOT listed in Table 2 - select 'Fitted'
      • VIN listed in Table 2 - select 'Not fitted'
      • VIN B03409 onward - select 'Not fitted
    VIN LIST

    VIN VIN VIN VIN
    B02989 B02993 B02995 B03002
    B03003 B03010 B03013 B03027
    B03030 B03031 B03033 B03034
    B03037 B03072 B03090 B03120
    B03127 B03132 B03136 B03140
    B03147 B03148 B03162 B03165
    B03167 B03169 B03171 B03174
    B03175 B03177 B03179 B03181
    B03184 B03202 B03223 B03227
    B03231 B03234 B03236 B03238
    B03239 B03243 B03244 B03245
    B03251 B03252 B03255 B03256
    B03258 B03259 B03262 B03265
    B03268 B03269 B03272 B03274
    B03278 B03280 B03283 B03285
    B03286 B03287 B03291 B03292
    B03293 B03297 B03301 B03315
    B03316 B03318 B03319 B03321
    B03322 B03324 B03325 B03328
    B03329 B03330 B03332 B03333
    B03336 B03340 B03342 B03343
    B03347 B03352 B03353 B03354
    B03356 B03371 B03375 B03378
    B03380 B03381 B03382 B03386
    B03389 B03390 B03396 B03398
    B03403 B03406 . .
  8. From the 'Configure New Modules' menu, select 'Restraints Control Module' and press 'tick' to continue.
  9. Follow all on-screen instructions to complete this task.
  10. When the task is completed, end the current session.
  11. Disconnect IDS and the power supply from the vehicle.
About FixVault