FixVault
Home › Jeep › 2020 › Gladiator Altitude, Automatic Trans › Repair and Diagnosis › External Pages › Different car › Section 12 (Front Suspension & Wheel Alignment) › Wheel Alignment › Technical Specifications › Measurement Specifications

Measurement Specifications

WARNING: This page is about a different car, the 2020 Chrysler 300 and 2019 Chrysler 300. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:

All specifications are given in degrees.

NOTE:

All wheel alignments are to be set at curb height. Refer to WHEEL ALIGNMENT, STANDARD PROCEDURE .

NOTE:

Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle's measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications.

Front Wheel Alignment Specifications
  Total Toe(2) Camber - Left Camber - Right Cross Camber(1) Caster - Left Caster - Right Cross Caster(1)
RWD  0.20° +/- 0.20° -0.85° +/- 0.55° -1.25° +/- 0.55° 0.40° +/- 0.55° 8.00° +/- 1.00° 8.70° +/- 1.00° -0.70° +/- 0.60°
AWD  0.10° +/- 0.20° -0.15° +/- 0.55° -0.55° +/- 0.55° 0.40° +/- 0.55° 5.40° +/- 1.00° 5.40° +/- 1.00° 0.00° +/- 0.60°
SRT  0.20° +/- 0.20° -0.95° + 0.55° / - 0.75° -1.35° + 0.55° / - 0.75° 0.40° +/- 0.55° 8.30° +/- 1.00° 9.00° +/- 1.00° -0.70° +/- 0.60°
RHD  0.20° +/- 0.20° -1.25° +/- 0.55° -0.85° +/- 0.55° -0.40° +/- 0.55° 8.35° +/- 1.00° 8.35° +/- 1.00° 0.00° +/- 0.60°
Notes:
(1) Cross Alignment values are determined by taking the left side value minus the right side value.

(2) TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.
Rear Wheel Alignment Specifications
  Toe - Left Toe - Right Thrust Angle Camber Cross Camber
RWD  0.10° +/- 0.15° 0.10° +/- 0.15° 0.00° +/- 0.15° -1.75° +/- 0.55° 0.00° +/- 0.80°
AWD  0.10° +/- 0.15° 0.10° +/- 0.15° 0.00° +/- 0.15° -0.50° +/- 0.55° 0.00° +/- 0.80°
SRT  0.10° +/- 0.15° 0.10° +/- 0.15° 0.00° +/- 0.15° -0.75° +/- 0.55° 0.00° +/- 0.80°
RHD  0.10° +/- 0.15° 0.10° +/- 0.15° 0.00° +/- 0.15° -1.75° +/- 0.55° 0.00° +/- 0.80°
Notes:
* For reference only. These are non adjustable angles.
About FixVault