FixVault
Home › Jeep › 2020 › Gladiator Altitude, Automatic Trans › Repair and Diagnosis › External Pages › Different car › Section 12 (Front Suspension & Wheel Alignment) › Wheel Alignment › Technical Specifications › Set-To Specifications

Set-To Specifications

WARNING: This page is about a different car, the 2020 Chrysler 300 and 2019 Chrysler 300. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:

All specifications are given in degrees.

NOTE:

All wheel alignments are to be set at curb height. Refer to WHEEL ALIGNMENT, STANDARD PROCEDURE .

NOTE:

With service there is both a set-to and service measurement check specifications. Set-to specifications are the parameters and tolerances used when adjusting alignment is necessary. A measurement specification is for the initial measurement of a vehicle in service. If this vehicle does not pass the measurement specification then the alignment should be adjusted to the set-to specification. Measurement specification is due to variation from measurement tools and setting.

Front Wheel Alignment Specifications
  Total Toe(2) Camber - Left Camber - Right Cross Camber(1) Caster - Left Caster - Right Cross Caster(1)
RWD  0.20° +/- 0.10° -0.85° +/- 0.55° -1.25° +/- 0.55° 0.40° +/- 0.55° 8.00° +/- 1.00° 8.70° +/- 1.00° -0.70° +/- 0.60°
AWD  0.10° +/- 0.10° -0.15° +/- 0.55° -0.55° +/- 0.55° 0.40° +/- 0.55° 5.40° +/- 1.00° 5.40° +/- 1.00° 0.00° +/- 0.60°
SRT  0.20° +/- 0.10° -0.95° +/- 0.55° -1.35° +/- 0.55° 0.40° +/- 0.55° 8.30° +/- 1.00° 9.00° +/- 1.00° -0.70° +/- 0.60°
RHD  0.20° +/- 0.10° -1.25° +/- 0.55° -0.85° +/- 0.55° -0.40° +/- 0.55° 8.35° +/- 1.00° 8.35° +/- 1.00° 0.00° +/- 0.60°
Notes:
(1) Cross Alignment values are determined by taking the left side value minus the right side value.

(2) TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.
Rear Wheel Alignment Specifications
  Toe - Left Toe - Right Thrust Angle Camber Cross Camber
RWD  0.10° +/- 0.15° 0.10° +/- 0.15° 0.00° +/- 0.15° -1.75° +/- 0.55° 0.00° +/- 0.80°
AWD  0.10° +/- 0.15° 0.10° +/- 0.15° 0.00° +/- 0.15° -0.50° +/- 0.55° 0.00° +/- 0.80°
SRT  0.10° +/- 0.15° 0.10° +/- 0.15° 0.00° +/- 0.15° -0.75° +/- 0.55° 0.00° +/- 0.80°
RHD  0.10° +/- 0.15° 0.10° +/- 0.15° 0.00° +/- 0.15° -1.75° +/- 0.55° 0.00° +/- 0.80°
Notes:
* For reference only. These are non adjustable angles.
About FixVault