Common Specs & Procedures
RENEGADE COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | REMOVAL AND INSTALLATION | ||
| Rear | REMOVAL AND INSTALLATION | ||
| Battery | Specifications not available from manufacturer | ||
| Brakes | |||
| Bleeding Sequence | Base Brakes: STANDARD PROCEDURE | ||
| Disc Brakes | |||
| Service Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | Specifications not available from manufacturer | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| 1.3L | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION . | ||
| 2.4L | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| 1.3L | |||
| Engine Coolant | COOLANT | ||
| Radiator Cap Pressure | Specifications not available from manufacturer | ||
| Thermostat R & I | REMOVAL AND INSTALLATION . | ||
| Water Pump R & I | REMOVAL AND INSTALLATION . | ||
| 2.4L | |||
| Engine Coolant | COOLANT | ||
| Radiator Cap Pressure | The cap is designed to hold up to 20 psi. | ||
| Thermostat R & I | REMOVAL AND INSTALLATION | ||
| Water Pump R & I | REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| 1.3L | |||
| Compression | CYLINDER COMPRESSION TEST | ||
| Oil Pressure | Specifications not available from manufacturer | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2.4L | |||
| Compression | CYLINDER COMPRESSION TEST | ||
| Oil pressure | At Curb Idle Speed. 25 kPa (4 psi min.) At 3000 RPM. 170-550 kPa (25 - 80 psi.) |
||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 1.3L | REMOVAL AND INSTALLATION | ||
| 2.4L | 21 Ft. Lbs. + 51° (29 N.m + 51°) | ||
| Fuel System | |||
| Pressure Specification | |||
| 1.3L | 407 kPa +/- 34 kPa (58 psi +/- 5 psi). | ||
| 2.4L | 407 kPa +/- 34 kPa (58 psi +/- 5 psi). | ||
| Fuel Pressure Test Procedure | |||
| 1.3L | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| 2.4L | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| Fuel Filter Location | |||
| 1.3L | Fuel filters are integrated into the main fuel pump module. | ||
| 2.4L | Fuel filters are integrated into the main fuel pump module. | ||
| Fuel Filter R & I | |||
| 1.3L | REMOVAL AND INSTALLATION | ||
| 2.4L | REMOVAL AND INSTALLATION | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 1.3L | |||
| Type | Recommended to use MOPAR Spark Plugs | ||
| Gap | 0.026 in (0.65 mm) | ||
| Torque | 13 Ft. Lbs. (18 N.m) | ||
| 2.4L | |||
| Type | Recommended to use MOPAR Spark Plugs | ||
| Gap | 0.026 in (0.65 mm) | ||
| Torque | 20 Ft. Lbs. (27 N.m) | ||
| Starting | |||
| Starter | Specifications not available from manufacturer | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | Front: TORQUE SPECIFICATIONS , Rear: TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 89 ft. lbs. (120 N.m) | ||