FixVault
Home › Jeep › 2021 › Compass Altitude, FWD › Repair and Diagnosis › Engine Performance › System › 2.4L - DTCS P1048 To P1D68 › DTC Troubleshooting › P152E-Engine Hood Switch 2 Circuit High › Diagnostic Test

Diagnostic Test

  1. READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN 
    1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
    2. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
    3. With the scan tool, erase all DTCs.
    4. Turn the ignition off for a minimum of 10.0 seconds.
    5. Turn the ignition on.
    6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    7. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Go To  2

      No 

  2. CHECK THE HOOD AJAR SWITCH 2 CONNECTOR AND TERMINALS 
    1. Turn the ignition off.
    2. Check the Hood Ajar Switch 2 harness connector for proper connection at the Hood Ajar Switch 2.
    3. Verify that the connector is completely plugged in and properly locked prior to disconnecting.
    4. Disconnect the Hood Ajar Switch 2 harness connector and check for any pushed out, damaged or spread terminals.

      Were any issues found with the connector or terminals?

      Yes 

      • Repair the damaged terminal or properly connect and lock the Hood Ajar Switch 2 harness connector and retest for DTCs.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  3
  3. CHECK THE HOOD AJAR SWITCH 2 FOR PROPER FUNCTION 
    1. Check the Hood Ajar Switch 2 functionality. Use the Hood Ajar Switch 2 diagnostic and technical information provided above.

      Is the Hood Ajar Switch 2 functioning properly?

      Yes 

      • Go To  4

      No 

      • Replace the Hood Ajar Switch 2 in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  4. CHECK THE (Z907) GROUND CIRCUIT FOR HIGH RESISTANCE BY LOAD TESTING THE CIRCUIT 
    NOTE:

    Read the CIRCUIT LOAD TESTING PROCEDURE for information on building a simple load test tool and for additional load testing information and alternative methods of load testing or voltage drop testing a circuit. Refer to STANDARD PROCEDURE .

    1. Turn the ignition off.
    2. Disconnect the Hood Ajar Switch 2 harness connector.
      CAUTION:

      Do not load test any circuits with components still connected to the circuit.

      GC0174957Courtesy of CHRYSLER GROUP, LLC
      NOTE:

      The bulb on the load test tool should be illuminated and bright if there is no resistance in the circuitry. Compare the brightness of the bulb in the load test tool to that of a direct connection across Battery.

      Is the load test bulb illuminated and bright?

      Yes 

      • Go To  5

      No 

      • Repair the ground circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  5. CHECK THE HOOD AJAR SWITCH 2 (K806) SIGNAL CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Disconnect the PCM C1 harness connector.
    2. Measure the resistance of the Hood Ajar Switch 2 (K806) Signal circuit between the Hood Ajar Switch 2 harness connector and the PCM C1 harness connector.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Go To  6

      No 

      • Repair the Hood Ajar Switch 2 (K806) Signal circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  6. CHECK RELATED PCM AND COMPONENT CONNECTIONS 
    1. Perform any Service Bulletins that apply.
    2. Disconnect all PCM harness connectors.
    3. Disconnect all related in-line harness connections (if equipped).
    4. Disconnect the related component harness connectors.
    5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    9. With the scan tool, erase DTCs.
    10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    11. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      No 

      • The wiring or poor connection problem has been repaired.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
About FixVault