FixVault
Home › Jeep › 2024 › Wagoneer Base, RWD › Repair and Diagnosis › Suspension › Suspension Control Systems › Front Suspension And Wheel Alignment › Wheel Alignment › Technical Specifications › Alignment Specifications

Alignment Specifications

NOTE:

For air suspension equipped vehicles, when checking or adjusting wheel alignment, the air suspension system must be set to Wheel Alignment Mode. The preferred method of setting the system to Wheel Alignment Mode is through the diagnostic scan tool. Wheel Alignment Mode in the radio menu can also be used if a diagnostic scan tool is not available.

NOTE:

All non-air suspension equipped vehicles are to be aligned at curb height. Refer to WHEEL ALIGNMENT, STANDARD PROCEDURE .

NOTE:

On air suspension equipped vehicles the ride height specifications apply to vehicles set to NRH (Normal Ride Height).

Front Wheel Alignment Measurement Check Specifications
  Total Toe Caster - Left Caster - Right Cross Caster Camber - Left Camber - Right Cross Camber
Tolerance +/- 0.20° +/- 0.65° +/- 0.65° +/- 0.65° +/- 0.65° +/- 0.65° +/- 0.65°
Steel Spring, Short Wheel Base  0.20° 5.24° 5.24° 0.00° - 0.07° - 0.07° 0.00°
Air Spring, Short Wheel Base  0.46° 5.24° 5.24° 0.00° - 0.07° - 0.07° 0.00°
Steel Spring, Long Wheel Base  0.20° 5.27° 5.27° 0.00° - 0.07° - 0.07° 0.00°
Air Spring, Long Wheel Base  0.46° 5.27° 5.27° 0.00° - 0.07° - 0.07° 0.00°
NOTE:

Steering wheel angle must be within specification before starting front toe set process.
NOTE:

All air ride vehicles are to be aligned at NRH.
Rear Wheel Alignment Measurement Check Specifications
  Individual Toe Total Toe Thrust Angle Camber - Left Camber - Right Cross Camber
Tolerance +/- 0.10° +/- 0.20° +/- 0.15° + 0.38 / - 0.88° + 0.38 / - 0.88° +/- 0.75°
Steel Spring, Short Wheel Base  0.10° 0.20° 0.00° - 0.40° - 0.40° 0.00°
Air Spring, Short Wheel Base  0.10° 0.20° 0.00° - 0.40° - 0.40° 0.00°
Steel Spring, Long Wheel Base  0.10° 0.20° 0.00° - 0.40° - 0.40° 0.00°
Air Spring, Long Wheel Base  0.10° 0.20° 0.00° - 0.40° - 0.40° 0.00°
NOTE:

Steering wheel angle must be within specification before starting front toe set process.
NOTE:

All air ride vehicles are to be aligned at NRH.
Front Wheel Alignment Set-To Specifications
  Total Toe Caster - Left Caster - Right Cross Caster* Camber - Left Camber - Right Cross Camber
Tolerance +/- 0.13° +/- 0.50° +/- 0.50° +/- 0.50° +/- 0.50° +/- 0.50° +/- 0.50°
Steel Spring, Short Wheel Base  0.20° 5.24° 5.24° 0.00° - 0.07° - 0.07° 0.00°
Air Spring, Short Wheel Base  0.46° 5.24° 5.24° 0.00° - 0.07° - 0.07° 0.00°
Steel Spring, Long Wheel Base  0.20° 5.27° 5.27° 0.00° - 0.07° - 0.07° 0.00°
Air Spring, Long Wheel Base  0.46° 5.27° 5.27° 0.00° - 0.07° - 0.07° 0.00°
NOTE:

Steering wheel angle must be within specification before starting front toe set process.
NOTE:

All air ride vehicles are to be aligned at NRH.
Rear Wheel Alignment Set-To Specifications
  Individual Toe Total Toe Thrust Angle Camber - Left Camber - Right Cross Camber
Tolerance +/- 0.10° +/- 0.20° +/- 0.15° + 0.38 / - 0.88° + 0.38 / - 0.88° +/- 0.75°
Steel Spring, Short Wheel Base  0.10° 0.20° 0.00° - 0.40° - 0.40° 0.00°
Air Spring, Short Wheel Base  0.10° 0.20° 0.00° - 0.40° - 0.40° 0.00°
Steel Spring, Long Wheel Base  0.10° 0.20° 0.00° - 0.40° - 0.40° 0.00°
Air Spring, Long Wheel Base  0.10° 0.20° 0.00° - 0.40° - 0.40° 0.00°
NOTE:

Steering wheel angle must be within specification before starting front toe set process.
NOTE:

All air ride vehicles are to be aligned at NRH.
RIDE HEIGHT SPECIFICATIONS WITH OR WITHOUT AIR SUSPENSION

Tolerance FRONT REAR
+/- 15 mm +/- 15 mm
Short Wheel Base 114 mm 53 mm
Long Wheel Base 114 mm 52 mm
About FixVault