FixVault

Section 13 (Audio/AVN System): Troubleshooting: Camera

WARNING: This page is about a different car, the 2021 Kia Soul. However, it is still accessible from the selected car via links, so may be relevant.
  1. Features/Misdiagnose cases
    Inspection Description
    (1) System features
    1. Camera system features
      1. Change to H/U camera mode at gear R
      2. Steering wheel feature with CAN enabled Camera
      3. Diagnostic Trouble Code (DTC) feature added to CAN enabled camera
      4. Video Format - current: Analog/YG, HI: LVDS applied (New)
      5. Camera power ON (below 35~40km/h, 2015 Q4)
    2. AVM system features
      1. Change to H/U Rear view camera and AVM display at gear R
      2. On gear D, Rear view → Front view change at speed below 10km/h (AVM is ON)
      3. On gear D, Navigation mode change at speed above 10km/h (AVM is ON)
      4. Video format: CVBS, S-VIDEO, Component, LVDS
    (2) Misdiagnose cases
    1. Camera misdiagnose cases
      1. Video quality: Rear view camera have low quality spec (0.3 megapixel), dirt on lens
      2. Bumper showing too much: Camera angle
      3. Blinks on start of ignition: Black curtain process for AVN boot spec
      4. Parking guideline length: Camera location
      5. Blue screen: Possible camera output defect from AVN, AVM (Possible connector, cable defect)
    2. AVM misdiagnose cases
      1. Top view distortion: In-line correction error. Re-correction fixes issue
      2. Broken image pixel: Incomplete correction due to power OFF during correction process
      3. Camera screen defect (Top/Front/Rear/Left/Right): Possible camera defect
  2. Camera issue (Black screen/Blue screen/Noise/Broken)
    Issue Inspection Description
    Camera issue(Black screen/Blue screen/Noise/Broken) (1) Duplicate issue
    • Check gear R
    • Open/close door
    • Test drive to duplicate issue
    1. Check gear R

      (Normal: Camera+ Guide line + warning message)

    2. Open/close door test

      (Duplicate issue at angles)

    3. Test drive

    (Drive impact)
    If issue duplicates, follow steps below
    Camera issue(Black screen/Blue screen/Noise/Broken) (2) Search & remove defect factor
    • Connection
    • Damage
    • Camera power
    • Display signal
    • Wiring
    *If AVM is installed, also test side doors
    1. Camera connection
      1. Remove trunk cover and find camera connector
      2. Connection must be locked in

      → Check display

    2. Check camera damage
      1. Remove any dirt on lens
      2. Damage on lens, cracks → Moist inside camera

      Fault by customer if camera is physically damaged from outside

    3. Check camera voltage at gear R
      1. Red line: 6.5V, Black line: GND
      2. If there is no 6.5V input follow below steps

        (1) Cable Power module

      3. Camera power source

        (1) AVN Direct: AVN → Camera

        (2) AVM: AVM → Camera

    Camera issue(Black screen/Blue screen/Noise/Broken) (2) Search & remove defect factor
    • Connection
    • Damage
    • Camera power
    • Display signal
    • Wiring
    1. Check with other monitor

      *If other monitor is not available, replace camera instead

      1. Use other monitor to test video input
      2. Yellow line: CVBS video, White: Video GND

      (1) Monitor /AVN X → AVN defect

      (2) Monitor X/AVN X → Camera defect

    2. Check camera ↔ AVN wiring
      1. Camera ↔ AVN Wiring check
      2. For Pin contact testing, include cable company if available
    Short on wire is common due to driving impact
  3. Display issue (Display quality/Foggy/Foreign object)
    Issue Inspection Description
    Display issue (Quality/Foggy/Foreign Object) (1) Duplicate issue
    • Check gear R
    1. Duplicate issue by checking gear R

      (Normal: Compare with other vehicle)

    (2) Search & remove defect factor
    • Camera status
    • Open/close trunk test
    1. Camera status
      1. Foreign object
      2. Damaged coating
      3. Clean lens using soft cloth
    2. Open/Close trunk test

      (Duplicate at certain angle)


    Lens assembly error caused lens move inside camera → Camera can be foggy
  4. Parking guideline (Distortion)
    Issue Inspection Description
    Parking guideline issue (Distortion) (1) Duplicate issue
    • Use parking guideline to test parking
     
    1. Use parking guideline to test parking
    2. Check if vehicle direction and guideline is match

    For safety, guideline appears +10cm wider(left/right) than actual vehicle
    (2) Search & remove defect factor
    • Confirm specs
    • Camera connection
     
    1. Confirm specs

      (Normal: Vehicle ↔ guideline within +,-15cm)

    2. Camera connection
    • Check camera bracket
    • Check screw status
    • Re-connect the screw and re-test

    Reason for 15cm deviation: 1. Camera setting deviation 2. Guideline width (Actual area 10cm)
  5. AVM (Distortion/Broken pixel)
    Issue Inspection Description
    AVM (Distortion/Broken pixel) (1) Duplicate issue
    • Parking test
    • Broken pixel on certain area
    1. Duplicate issue at gear R

      (Normal: Top view, parking line is straight)

      *Top view is displayed on the right

    2. Check for broken pixel

    (Cause: data store error during correction)
    Above issues can be treated with re-correction process
    (2) Search & remove defect factor
    • Re-correction
    • Replace Camera/AVM
    1. Re-correction
      1. Service center AVM correction room (Recommended)
    2. If issue continues, replace camera/AVM and re-test
    1. Possible camera output defect
    2. Possible correction data memory defect

    5. AVM Defect (black & white screen)

Issue Inspection Description
AVM (No colors) (1) Duplicate issue
  • Check gear R
  • Test drive
  1. Duplicate issue at gear R

    (Check black/white screen)

  2. Test drive to duplicate issue

(Drive on rough road to supply shock with vehicle)
OSD outputs from AVN *Color (OSD: Select view mode, Door open UI)
(2) Search & remove defect factor
  • Re-correction
  • Replace test
* Check if issue gets resolved when tapping on AVM connector Cable/Connector issue
  1. Inspect AVM VOUT_C
    1. Check vehicle spec (S-VIDEO, Component)

      (1) Check with related department with vehicle spec

    2. Luminance (Y)+Color (C)=Video/Black screen if color signal is not available

    *Component: Use 2 C signals (Cb, Cr)

  2. Check AVM connector
    1. Connector connection (Must be locked)
    2. Check tension on Vehicle female connector

VOUT_C(A10) tension (2.5 )