Engine (V8 5.0L Petrol): Specifications
Engine Data
| Engine Description | Engine Capacity | Maximum Engine Torque (EEC) | Maximum Engine Power (EEC) | Compression Ratio | Bore | Stroke |
|---|---|---|---|---|---|---|
| 90° "Vee" 8 Cylinder 32 Valves | 4.999 ccm | 510 Nm at 3.500 RPM | 276 kW at 6.500 RPM | 11.5 ± 0.5 | 92.5 mm | 93 mm |
Engine Firing Order
| Firing Order |
|---|
| 1:2:7:3:4:5:6:8 |
Engine Valve Clearance (cold)
| Intake Valve | Exhaust Valve |
|---|---|
| N/A | 0.25 mm ± 0.02 |
Spark Plugs
| Specification | Spark Plug Gap |
|---|---|
| ILKR6C-10 | 1 mm |
Lubricants, Fluids, Sealers and Adhesives
| Description | Specification |
|---|---|
| Engine Oil | WSS-M2C925-A |
| Sealant | WSE-M4G323-A6 |
| Core plug and stub pipe retainer | WSK-M2G349-A7 |
Capacities
| Description | Liters |
|---|---|
| Engine oil, initial fill | 9.5 |
| Engine oil, service fill with oil filter change | 8.0 |
Cylinder Head and Valve Train
| Item | Specification |
|---|---|
| Cylinder head maximum permitted warp (mm) (flatnes specfication) | |
| overall | 0.08 |
| over 150x150 mm area | 0.05 |
| over 25x25 mm area | 0.02 |
| Valve guide inner diameter (mm) | 5.51 ± 0.01 |
| Intake valve effective length (mm) (tip to gauge line) | 97.63 ± 0.1 |
| Exhaust valve effective length (mm) (tip to gauge line) | 94.39 ± 0.1 |
| Valve stem to guide clearance intake diametrical (mm) | 0.022 - 0.057 |
| Valve stem to guide clearance exhaust diametrical (mm) | 0.03 - 0.065 |
| Valve head diameter intake (mm) | 36 ± 0.1 |
| Valve head diameter exhaust (mm) | 30 ± 0.1 |
| Intake valve face angle (degrees) | 44.875 ± 0.125 |
| Exhaust valve face angle (degrees) | 44.875 ± 0.125 |
| Valve stem diameter intake (mm) | 5.4705 ± 0.0075 |
| Valve stem diameter exhaust (mm) | 5.4625 ± 0.0075 |
| Valve spring free length (mm) - inlet | 43.43 |
| Valve spring free length (mm) - exhaust | 46.1 |
| Valve spring installed height (mm) - inlet | 34.49 |
| Valve spring installed height (mm) - exhaust | 35.1 |
| Camshaft lobe lift intake (mm) | 5.5 (low) 10.53 (high) |
| Camshaft lobe lift exhaust (mm) | 9.36 |
| Camshaft journal to cylinder head bearing surface clearance diametrical (mm) | 0.025 - 0.065 |
| Camshaft journal diameter - all positions | 26.965 ± 0.01 |
| Bearing diameter - all positions | 27.01 ± 0.01 |
| Camshaft journal maximum run out limit (mm) | |
| Camshaft journals to end journals | 0.03 |
| Camshaft journals to adjacent journals | 0.015 |
| Camshaft journal maximum out of round (mm) - all journals | 0.005 |
Torque Specifications
NOTE:
A = Refer to procedure for correct torque sequence.
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Engine cover mounting bolts | 10 | 7 | - |
| Accessory drive belt tensioner retaining bolt | 40 | 30 | - |
| Supercharger belt idler/tensioner bracket retaining bolts | 25 | 18 | - |
| Secondary drive belt idler retaining bolts | 40 | 30 | - |
| Power steering pump pulley retaining bolts | 25 | 18 | - |
| Power steering pump retaining bolts | 25 | 18 | - |
| Power steering pump bracket to engine retaining bolts | 25 | 18 | - |
| Generator retaining bolts | 48 | 35 | - |
| Starter motor retaining bolts | 40 | 30 | - |
| Air conditioning compressor retaining bolts | 25 | 18 | - |
| Engine mounting to engine mounting bracket retaining nuts | 100 | 74 | - |
| Engine mounting to subframe retaining bolts | 56 | 41 | - |
| Engine mounting bracket to engine retaining bolts | 45 + 60° | 33 + 60° | - |
| Crankshaft damper pulley retaining LH threaded bolt | 200 + 270° | 148 + 180° | - |
| Flexplate retaining bolts | 45 + 90° | 33 + 90° | - |
| Exhaust manifold heat shield retaining bolts | A | - | - |
| Exhaust manifold retaining bolts | A | - | - |
| Engine wiring harness bracket retaining bolts | 10 | 7 | - |
| Coolant outlet pipe | 10 | 7 | - |
| Intercooler retaining bolts | 25 | 18 | - |
| Intake manifold retaining bolts | 25 | 18 | - |
| Oil Cooler retaining bolts | 13 | 10 | - |
| Knock sensor (KS) retaining bolt | 20 | 14 | - |
| Ignition coil retaining bolts | 8 | - | 71 |
| Spark plugs | 20 | 15 | - |
| Fuel rail retaining bolts | A | - | - |
| High pressure fuel pipe retaining bolts | A | - | - |
| High pressure fuel pump retaining bolts | 12 | 9 | - |
| Oil filter housing assembly retaining bolts | 12 | 9 | - |
| Oil filter cap | 25 | 18 | - |
| Lifting eye bolts | 25 + 90° | 18 + 90° | - |
| Manifold absolute pressure and temperature (MAPT) sensor retaining bolts | 5 | - | 44 |
| Coolant pump retaining bolts | 12 | 9 | - |
| Variable valve timing (VVT) oil control solenoid retaining bolts | 10 | 7 | - |
| Camshaft position (CMP) sensor retaining bolts | 10 | 7 | - |
| Camshaft cover retaining bolts | 13 | 10 | - |
| Front upper timing cover retaining bolts | 12 | 9 | - |
| Front lower timing cover retaining bolts | A | - | - |
| Engine rear cover retaining bolts | A | - | - |
| VVT to camshaft retaining bolts | 32 | 24 | - |
| Camshaft bearing caps retaining bolts | 11 | 8 | - |
| Primary timing chain fixed guide retaining bolts | 12 | 9 | - |
| Primary timing chain tensioner retaining bolts | 12 | 9 | - |
| Primary timing chain tensioner guide blade retaining bolts | 25 | 18 | - |
| Auxiliary chain tensioner guide retaining bolts | 21 | 15 | - |
| Auxiliary chain fixed guide retaining bolt | 12 | 9 | - |
| Oil pump sprocket retaining bolt | 21 | 15 | - |
| Cylinder head retaining bolts | A | - | - |
| Engine oil level (EOL) sensor retaining bolt | 12 | 9 | - |
| Crankshaft position (CKP) sensor retaining bolt | 10 | 7 | - |
| Oil sump body to engine retaining bolts | 25 | 18 | - |
| Oil pan drain plug | 24 | 18 | - |
| Oil transfer tube to Oil pan body retaining bolts | 11 | 8 | - |
| Oil pump to engine block retaining bolts | 25 | 18 | - |
| Pick-up pipe to oil pump retaining bolts | 12 | 9 | - |
| Windage tray retaining bolts | 25 | 18 | - |
| Piston cooling jet retaining bolts | 12 | 9 | - |
| Engine block coolant draining plug | 50 | 37 | - |
| Cooling fan pulley | 25 | 18 | - |
| Connecting Rod Bolts | |||
| Stage 1 | 10 | 7 | - |
| Stage 2 | 50 | 37 | - |
| Main Bearing Cap | |||
| M10 bolt stage 1 | 25 | 18 | - |
| M10 bolt stage 2 | 57 + 70° | 42 + 70° | - |
| M8 bolt stage 1 | 15 | 11 | - |
| M8 bolt stage 2 | 33 + 75° | 24 + 75° | - |