Section 390 (Lighting System): Inspection

1. Inspect the light control switch continuity.
   1. Check continuity between terminals at each switch position as shown in the chart.
   SPECIFIED TESTER CONDITION
   
   

   Switch operation	Tester connection	Specified condition
   OFF	-	No continuity
   TAIL	14 - 16	Continuity
   HEAD	13 - 16 - 14	Continuity
   AUTO	16 - 12	Continuity

   Fig 1: Inspecting Light Control Switch Continuity

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Inspect the headlamp dimmer switch continuity.
   1. Check continuity between terminals at each switch position as shown in the chart.
   SPECIFIED TESTER CONDITION
   
   

   Switch operation	Tester connection	Specified condition
   FLASH	7 - 8 - 16	Continuity
   LOW BEAM	16 - 17	Continuity
   HI BEAM	7 - 16	Continuity

3. Inspect the turn signal switch continuity.
   1. Check continuity between terminals at each switch position as shown in the chart.
   SPECIFIED TESTER CONDITION
   
   

   Switch operation	Tester connection	Specified condition
   Right turn	2 - 3	Continuity
   Neutral	-	No continuity
   Left turn	1 - 2	Continuity

4. Inspect the front fog lamp switch continuity.
   1. Check continuity between terminals at each switch position as shown in the chart.
   SPECIFIED TESTER CONDITION
   
   

   Switch operation	Tester connection	Specified condition
   OFF	-	No continuity
   ON	10 - 11	Continuity

   Fig 2: Inspecting Front Fog Lamp Switch

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Check continuity between terminals at each switch position as shown in the chart.
   SPECIFIED TESTER CONDITION
   
   

   Switch operation	Tester connection	Specified condition
   OFF	2 - 3	No continuity
   ON	2 - 3	Continuity
   Illumination circuit	4 - 5	Continuity

2. Inspect illumination operation.
   1. Connect the battery positive (+) lead to terminal 4 and the battery negative (-) lead to terminal 5, then check that the illumination comes on.

1. Inspect courtesy lamp assy continuity.
   1. Check continuity between terminals when the switch is operated.

   Standard: 

   ON (When shaft is pressed): No continuity 

   OFF (When shaft is not pressed): Continuity 

1. Inspect courtesy lamp assy continuity.
   1. Check continuity between terminal and the switch body when the switch is operated.

   Standard: 

   ON (When shaft is pressed): No continuity 

   OFF (When shaft is not pressed): Continuity 

1. Inspect courtesy lamp assy continuity.
   1. Check continuity between terminal and the switch body when the switch is operated.

   Standard: 

   ON (When shaft is pressed): No continuity 

   OFF (When shaft is not pressed): Continuity 

1. Inspect courtesy lamp assy continuity.
   1. Check continuity between terminals when the switch is operated.

   Standard: 

   ON (When shaft is pressed): No continuity 

   OFF (When shaft is not pressed): Continuity 

1. Inspect relay continuity.

Standard: 

Fig 3: Identifying Hazard Warning Signal Switch Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect relay continuity.

Standard: 

Fig 4: Identifying Tail Lamp Relay

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect the relay continuity.

Fig 5: Identifying Fog Lamp Relay

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect relay continuity.

Standard: 

Fig 6: Identifying Room Lamp Control Relay (Dome Relay)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect relay continuity.

Standard: 

Fig 7: Identifying Park/Neutral Position Switch Relay (BK/Up Relay) Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect relay continuity.

Standard: 

Fig 8: Identifying Towing Converter Relay (BATT CHG Relay)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect relay continuity.

Standard: 

Fig 9: Inspecting Relay

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Connect the battery positive (+) lead to terminal 2 and the battery negative (-) lead to terminal 6, and check that the indicator light comes on.

Fig 10: Transponder Key amplifier Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect map light assy continuity.
   1. Check continuity between terminals at each switch position as shown in the chart.

   Standard: 

   SPECIFIED TESTER CONDITION
   
   

   Switch operation	Tester connection	Specified condition
   OFF	-	No continuity
   DOOR	7 (+B) - 2 (DOOR)	Continuity
   ON	7 (+B) - 4 (E)	Continuity

   Fig 11: Identifying Map Lamp Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect room lamp assy No.1 continuity.
   1. Check continuity between terminals at each switch position as shown in the chart.
   Fig 12: Inspecting Room Lamp

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Standard: 

Fig 13: Identifying Room Lamp Assembly Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect room lamp assy No.2 continuity.
   1. Check continuity between terminals at each switch position as shown in the chart.

Standard: 

1. Check continuity between terminals.

   Standard: Continuity exists 

1. Check continuity between terminals.

   Standard: Continuity exists 

1. Check continuity between terminals.

   Standard: Continuity exists 

1. Inspect vanity light continuity.
   1. Check continuity between terminal 1 and 2 when the light is operated.

   Standard: 

   OFF (closed): No continuity 

   ON (opened): Continuity 

1. Inspect vanity light continuity.
   1. Check continuity between terminal 1 and 2 when the light is operated.

   Standard: 

   OFF (closed): No continuity 

   ON (opened): Continuity 

1. Check continuity between terminals at each switch position as shown in the chart.

Standard: 

Fig 14: Identifying Stop Lamp Switch Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

(Inside Handle Illumination) 

1. Check continuity between terminal 1 (+B) and 2 (GND).

   Standard: Continuity 

HINT:

Connect the positive (+) terminal of the tester to the terminal 1 (+B) of the connector, and the negative (-) terminal of the tester to the terminal 2 (GND) of the connector to check the continuity.

Fig 15: Identifying Lamp Interior Illumination Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

(Driver Side Foot Light) 

1. Check continuity between terminal 1 (+B) and 2 (GND).
   Fig 16: Identifying Interior Illumination Lamp Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard: Continuity 

HINT:

Connect the positive (+) terminal of the tester to the terminal 1 (+B) of the connector, and the negative (-) terminal of the tester to the terminal 2 (GND) of the connector to check the continuity.

(Front Passenger Side Foot Light) 

1. Check continuity between terminal 1 (+B) and 2 (GND).

   Standard: Continuity 

HINT:

Connect the positive (+) terminal of the tester to the terminal 1 (+B) of the connector, and the negative (-) terminal of the tester to the terminal 2 (GND) of the connector to check the continuity.

Fig 17: Identifying Interior Illumination Lamp Assembly Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Inspect the side step lamp assy.
   1. Check continuity between terminals when the courtesy lamp switch is operated.

   Standard: 

   ON: Continuity 

   OFF: No continuity 

1. (2) Check continuity between terminals when the courtesy lamp switch is operated.

Standard: 

ON: Continuity 

OFF: No continuity