FixVault
Home › Lexus › 2004 › LS 430 › Repair and Diagnosis › Transmission › Automatic Trans › Automatic Transmission (On-Vehicle Service) › Park/Neutral Position Switch ASSY › Replacement

Park/Neutral Position Switch ASSY: Replacement

  1. DISCONNECT BATTERY NEGATIVE TERMINAL 
  2. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO. 2 (SEE  REPLACEMENT  ) 
  3. REMOVE INSTRUMENT PANEL GARNISH SUB-ASSY LH (SEE  REPLACEMENT  ) 
  4. REMOVE INSTRUMENT PANEL FINISH PANEL (SEE  REPLACEMENT  ) 
  5. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO. 1 (SEE  REPLACEMENT  ) 
  6. REMOVE SWITCH BRACE HOLE COVER (SEE  REPLACEMENT  ) 
  7. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSY NO. 1 (SEE  REPLACEMENT  ) 
  8. REMOVE INSTRUMENT PANEL CUP HOLDER ASSY (SEE  REPLACEMENT  ) 
  9. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSY (SEE  REPLACEMENT  ) 
  10. REMOVE CONSOLE BOX CARPET (SEE  REPLACEMENT  ) 
  11. REMOVE REAR CONSOLE ARMREST ASSY (SEE  REPLACEMENT  ) 
  12. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER (SEE  REPLACEMENT  ) 
  13. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSY CENTER (SEE  REPLACEMENT  ) 
  14. REMOVE CONSOLE PANEL SUB-ASSY UPPER (SEE  REPLACEMENT  ) 
  15. REMOVE CONSOLE BOX (SEE  REPLACEMENT  ) 
  16. SEPARATE OXYGEN SENSOR (SEE  REPLACEMENT  ) 
  17. REMOVE FRONT FLOOR BRACE CENTER (SEE  REPLACEMENT  ) 
  18. REMOVE EXHAUST PIPE ASSY (SEE  REPLACEMENT  ) 
  19. REMOVE FRONT FLOOR HEAT INSULATOR NO. 1 (SEE  REPLACEMENT  ) 
  20. REMOVE PROPELLER W/CENTER BEARING SHAFT ASSY (SEE  OVERHAUL  ) 

    SST 09922-10010

  21. SEPARATE FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSY 
    1. Remove the nut and separate the floor shift gear shifting rod.
      Fig 1: Removing Nut And Separate Floor Shift Gear Shifting Rod
      G01028834Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. SUPPORT AUTOMATIC TRANSMISSION ASSY 
    1. Support the automatic transmission assy with a transmission jack.
      Fig 2: Supporting Automatic Transmission Assy With Transmission Jack
      G01028835Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. SEPARATE ENGINE REAR MOUNTING MEMBER 
    1. Remove the 4 bolts and separate the engine rear mounting member.
  24. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH 
    1. Remove the nut and transmission control shaft lever RH.
      Fig 3: Removing Bolts And Separate Engine Rear Mounting Member
      G01028836Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. REMOVE PARK/NEUTRAL POSITION SWITCH ASSY 
    1. Disconnect the park/neutral position switch connector.
    2. Using a screwdriver, pry out the lock washer.
    3. Remove the lock nut and lock washer.
      Fig 4: Removing Lock Nut And Lock Washer
      G01028837Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the bolt and park/neutral position switch.
      Fig 5: Removing Bolt And Park/Neutral Position Switch
      G01028838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. INSTALL PARK/NEUTRAL POSITION SWITCH ASSY 
    1. Install the park/neutral position switch to the manual valve shaft.
    2. Temporarily install the bolt.
      Fig 6: Installing Park/Neutral Position Switch To Manual Valve Shaft
      G01028839Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install a new lock plate and the nut.

      Torque: 6.9 N.m (70 kgf.cm, 61 in.lbf) 

    4. Temporarily install the control shaft lever.
      Fig 7: Installing Lock Plate And Nut
      G01028840Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Turn the control shaft lever counterclockwise until it stops, and turn it clockwise 2 notches to set it to the N position.
    6. Remove the transmission control shaft lever.
      Fig 8: Removing Transmission Control Shaft Lever
      G01028841Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Align the neutral basic line with the switch groove, and tighten the adjusting bolt.

      Torque: 13 N.m (130 kgf.cm, 9 ft.lbf) 

      Fig 9: Aligning Neutral Basic Line With Switch Groove
      G01028842Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Using a screwdriver, bend the tabs of the lock washer.
      Fig 10: Bending Tabs Of Lock Washer
      G01028843Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. INSTALL TRANSMISSION CONTROL SHAFT LEVER RH 
    1. Install the transmission control shaft lever RH with the nut.

      Torque: 16 N.m (160 kgf.cm, 12 ft.lbf) 

    2. Connect the park/neutral position switch connector.
      Fig 11: Installing Transmission Control Shaft Lever RH With Nut
      G01028844Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. INSTALL ENGINE REAR MOUNTING MEMBER 
    1. Install the engine rear mounting member with the 4 bolts.

      Torque: 26 N.m (270 kgf.cm, 20 ft.lbf) 

      Fig 12: Installing Engine Rear Mounting Member With 4 Bolts
      G01028845Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSY 
    1. Connect the floor shift gear shifting rod sub-assy with the nut.

      Torque: 13 N.m (130 kgf.cm, 9 ft.lbf) 

      Fig 13: Connecting Floor Shift Gear Shifting Rod Sub-Assy With Nut
      G01028846Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. CONNECT BATTERY NEGATIVE TERMINAL 
  31. ADJUST SHIFT LEVER POSITION (SEE  ADJUSTMENT  ) 
  32. INSPECT SHIFT LEVER POSITION (SEE  ADJUSTMENT  ) 
  33. INSPECT PARK/NEUTRAL POSITION SWITCH ASSY (SEE  ADJUSTMENT  ) 
  34. INSTALL PROPELLER W/CENTER BEARING SHAFT ASSY (SEE  OVERHAUL  ) 
  35. INSTALL EXHAUST PIPE ASSY (SEE  REPLACEMENT  ) 
  36. PERFORM INITIALIZATION (SEE  INITIALIZATION  ) 
About FixVault