Rear Axle Carrier: Installation

INSTALL REAR AXLE CARRIER SUB-ASSEMBLY
1. Install the rear axle carrier sub-assembly to the shock absorber with the 2 bolts and 2 nuts. Torque: 180 N*m (1,836 kgf*cm, 133 ft.*lbf)
  
  Fig 1: Locating Rear Axle Carrier Sub-Assembly LH With Bolts And Nuts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM
1. Temporarily tighten the rear No. 1 suspension arm with the bolt and nut.
  HINT:
  
  Insert the bolt from the rear side of the vehicle and temporarily tighten the bolt.
  
  Fig 2: Locating Rear Suspension Arm Assembly No.1 LH Bolt And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM
1. Temporarily tighten the rear No. 2 suspension arm with the bolt and nut.
  HINT:
  
  Insert the bolt from the rear side of the vehicle and temporarily tighten the bolt.
  
  Fig 3: Locating Rear Suspension Arm Assembly No.2 LH Bolt And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
TEMPORARILY TIGHTEN REAR STRUT ROD
1. Temporarily tighten the rear strut rod with the bolt and nut.
  HINT:
  
  Insert the bolt from the inside of the vehicle and temporarily tighten the bolt.
INSTALL REAR AXLE HUB AND BEARING ASSEMBLY (See INSTALLATION )
INSPECT REAR AXLE HUB BEARING LOOSENESS (See ON-VEHICLE INSPECTION )
INSPECT REAR AXLE HUB RUNOUT (See ON-VEHICLE INSPECTION )
INSTALL REAR DISC (See REASSEMBLY )
INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
1. Install the rear disc brake caliper with the 2 bolts. Torque: 62 N*m (630 kgf*cm, 46 ft.*lbf)
  NOTE: Do not twist the brake hose when installing the rear disc brake caliper assembly LH.
  
  Fig 4: Locating Rear Disc Brake Caliper With Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the rear flexible hose with the bolt. Torque: 19 N*m (192 kgf*cm, 14 ft.*lbf)
INSTALL REAR WHEEL
Torque: 103 N*m (1,050 kgf*cm, 76 ft.*lbf)
STABILIZE SUSPENSION (See INSTALLATION )

Fig 5: Locating Rear Flexible Hose With Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM
1. Fully tighten the bolt.
  Torque: 100 N*m (1,020 kgf*cm, 74 ft.*lbf)
  
  Fig 6: Locating Rear No. 1 Suspension Arm Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM
1. Fully tighten the bolt.
  Torque: 100 N*m (1,020 kgf*cm, 74 ft.*lbf)
  
  Fig 7: Locating Rear No. 2 Suspension Arm Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
FULLY TIGHTEN REAR STRUT ROD
1. Fully tighten the bolt.
  Torque: 113 N*m (1,150 kgf*cm, 83 ft.*lbf)
CONNECT SKID CONTROL SENSOR CONNECTOR (See INSTALLATION )
INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (w/ HID Headlight System)
HINT:

Perform the procedure only when installing the RH side. (See INSTALLATION )

Fig 8: Locating Rear Strut Rod Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
ADJUST REAR WHEEL ALIGNMENT
HINT:

See REAR WHEEL ALIGNMENT
CHECK ABS SPEED SENSOR SIGNAL
HINT:

See TEST MODE PROCEDURE
HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION (w/ HID Headlight System)
HINT:

See INITIALIZATION