FixVault
Home › Lexus › 2007 › ES 350 › Repair and Diagnosis › Restraints › Air Bag, SRS › Pre-Collision › Pre-Collision System › Data List / Active Test

Data List / Active Test

  1. DATA LIST 

    HINT:

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful as intermittent conditions or signals may be discovered before parts or wiring are disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the intelligent tester (with CAN VIM) to the DLC3.
    2. Turn the engine switch on (IG).
      Fig 1: Connecting Intelligent Tester To DLC3
      G05251340Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. By following the display on the tester, select the "Data List".

      PRE-COLLISION: 

      DATA LIST - PRE-COLLISION

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D BUCKLE SW Buckle switch status of driver's seat / UNSET: Unfasten driver side seat belt
      SET: Fasten driver side seat belt
      NG: Indeterminate data      		 UNSET/SET -
      P BUCKLE SW Buckle switch status of passenger's seat / UNSET: Unfasten passenger side seat belt
      SET: Fasten passenger side seat belt
      NG: Indeterminate data      		 UNSET/SET -
      D BELT CTRL Seat belt control status of driver's seat / STOP: Control stopped
      ON: Controlled
      ERROR: Indeterminate data      		 STOP / ON Seat belt (driver side) is fastened
      P BELT CTRL Seat belt control status of passenger's seat / STOP: Control stopped
      ON: Controlled
      ERROR: Indeterminate data      		 STOP/ ON Seat belt (passenger side) is fastened
      #PRESENT CODES Number of present trouble codes / min: 0, max: 255 Number of DTCs will be displayed -
      #PAST CODES Number of past trouble codes / min: 0, max: 255 Number of DTCs will be displayed -
  2. ACTIVE TEST 

    HINT:

    Using the intelligent tester to perform Active Test allows the operation or effects of relays, VSVs, actuators and other items to be tested without removing any parts. This non-intrusive inspection can be very useful as intermittent conditions or operation may be discovered before parts or wiring are disturbed. Using the Active Test early in troubleshooting is one way to save diagnostic time. It is possible to view Data List information on the intelligent tester while performing Active Tests.

    1. Connect the intelligent tester (with CAN VIM) to the DLC3.
    2. Turn the engine switch on (IG).
    3. Following the display on the tester, select the "Active Test".
      Fig 2: Connecting Intelligent Tester To DLC3
      G05251340Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      PRE-COLLISION: 

      ACTIVE TEST - PRE-COLLISION

      Tester Display Test Part Control Range Diagnostic Note
      D BELT MOTOR Driver's seat belt motor ON: Seat belt motor operates
      OFF: Seat belt motor does not operate      		 Seat belt (driver side) is fastened
      P BELT MOTOR Passenger's seat belt motor ON: Seat belt motor operates
      OFF: Seat belt motor does not operate      		 Seat belt (passenger side) is fastened
      D-P BELT MOTOR Driver's and passenger's seat belt motor ON: Seat belt motors operate
      OFF: Seat belt motors do not operate      		 Seat belts (driver and passenger) are fastened
      NOTE:
      • The belt motor does not operate when the buckle switch is off.
      • Do not operate the motor continuously to prevent overheating of the motor. Allow a 30 second interval between each test.
About FixVault