Inspection Procedure

1. Select the ACTIVE TEST, use the intelligent tester or Techstream to generate a control command, and then check the power seat motor function.
   1. Intelligent tester

      D-SEAT 

      INTELLIGENT TESTER - D-SEAT REFERENCE
      
      

      Tester Display	Test Part	Control Range
      CUSHION	Seat cushion length operation	FRONT/REAR

   2. Techstream

      Driver Seat 

      TECHSTREAM - DRIVER SEAT REFERENCE
      
      

      Tester Display	Test Part	Control Range
      Cushion Length	Seat cushion length operation	FRONT/REAR

      OK: Motor operates normally 

NG: Go to step   6 

OK: GO TO NEXT STEP 

Fig 1: Identifying e46 And e41 Connectors Terminals
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Disconnect the e46 switch connector.
2. Disconnect the e41 sensor connector.
3. Measure the resistance according to the values in the table below.

   Standard resistance 

   FRONT POWER SEAT SWITCH LH - FRONT POWER SEAT CUSHION POSITION SENSOR LH AND BODY GROUND
   
   

   Tester Connection	Condition	Specified Condition
   e46-8(PVCC) - e41-3 (VCC)	Always	Below 1 Ω
   e46-20(SSRC) - e41-1 (O/P)	Always	Below 1 Ω
   e46-18(SGND) - e41-2 (GND)	Always	Below 1 Ω
   e46-8 (PVCC) - Body ground	Always	10 kΩ or higher
   e46-20 (SSRC) - Body ground	Always	10 kΩ or higher
   e46-18 (SGND) - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: GO TO NEXT STEP 

Fig 2: Identifying e41 Connector Terminals
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Disconnect the e41 sensor connector.
2. Measure the voltage according to the values in the table below.

   Standard voltage 

   FRONT SEAT ADJUSTER ASSEMBLY LH (POSITION CONTROL SENSOR)
   
   

   Tester Connection	Switch Condition	Specified Condition
   e41-3(VCC) - e41-2 (GND)	Cushion switch signal ON	7.2 to 8.8 V

NG: REPLACE FRONT POWER SEAT SWITCH LH (See  REMOVAL  ) 

OK: GO TO NEXT STEP 

Fig 3: Identifying e41 Connector Terminal O/P
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Reconnect the e41 sensor connector.
2. Measure the voltage according to the value in the table below.

   Standard voltage 

   FRONT SEAT ADJUSTER ASSEMBLY LH (POSITION CONTROL SENSOR)
   
   

   Tester Connection	Switch Condition	Specified Condition
   e41-1 (O/P) - Body ground	Cushion switch signal ON	0 to 8V

NG: REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (See  REMOVAL  ) 

OK: GO TO NEXT STEP 

1. Clear the DTC (see DTC CHECK / CLEAR  ).
2. Recheck the DTC.

   OK: DTC B2655 is not output. 

NG: REPLACE FRONT POWER SEAT SWITCH LH (See  REMOVAL  ) 

OK: END (SYSTEM RETURNS TO NORMAL) 

Fig 4: Identifying Power Seat Motor Connector Terminals
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Check operation of the seat frame (cushion motor).
   1. Check if the seat adjuster moves smoothly when the battery is connected to the cushion motor connector terminals.

      OK 

      FRONT SEAT ADJUSTER ASSEMBLY LH (POWER SEAT MOTOR)
      
      

      Measurement Condition	Operational Direction
      Battery positive (+) → 1 Battery negative (-) → 2	Forward
      Battery positive (+) → 2 Battery negative (-) → 1	Backward

NG: REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (See  REMOVAL  ) 

OK: GO TO NEXT STEP 

Fig 5: Identifying e45 And e46 Connectors Terminals
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Disconnect the e45 and e46 switch connectors.
2. Disconnect the e40 motor connector.
3. Measure the resistance according to the values in the table below.

   Standard resistance 

   FRONT POWER SEAT SWITCH LH - POWER SEAT MOTOR
   
   

   Tester Connection	Condition	Specified Condition
   e46-10(C+) - e40-1	Always	Below 1 Ω
   e45-4 (C-) - e40-2	Always	Below 1 Ω

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: REPLACE FRONT POWER SEAT SWITCH LH (See  REMOVAL  )