Data List / Active Test

HINT:

Using the intelligent tester or Techstream to read the DATA LIST allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

1. Connect the intelligent tester or Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the tester on.
4. Enter the menus.
5. Enter the following menus:
   1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / BODY SYSTEM / SMART ACCESS / DATA LIST.
   2. Techstream - Select: Body Electrical / Smart Access / Data List.
6. According to the display on tester, read the "DATA LIST" or "Data List".
   1. Intelligent tester

      SMART ACCESS: 

      INTELLIGENT TESTER SMART ACCESS DATA LIST
      
      

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      IGSW	Engine switch on (IG) signal/ON or OFF	ON: Engine switch on (ACC, IG) OFF: Engine switch off or on (ACC)	-
      IMMOBILISER	Engine immobiliser system status/SET or UNSET	SET: Key is not in cabin UNSET: Key is in cabin	-
      MASTER KEY	Master key code signal/MATCH or NO MATCH	MATCH: Master key code is sent NO MATCH: Unmatched master key code is sent	-
      ENCRYPT CODE	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      SERIAL NUMBER	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      FRAME	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      RESPONSE	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      BCC	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      STATUS	Transponder chip data/OK or NG	OK: Data OK NG: Data error	-
      IDBX SLEEP COND	ID code box condition/YES or NO	YES: ID code box can be sleep condition NO: ID code box cannot be sleep condition	-
      IDBX START COND	ID code box condition/YES or NO	YES: ID code box sends wake up signal NO: ID code box does not send wake up signal	-
      EFI CODE RECEIVE	SFI code receive (when DTC detected) /OK or NG	OK: SFI code is received NG: SFI code is not received	-
      S CODE CHK	S code verification result/OK or NG	OK: Verification is confirmed NG: Verification is not confirmed	-
      L CODE CHK	L code verification result/OK or NG	OK: Verification is confirmed NG: Verification is not confirmed	-
      LCK RQ RECEIVE	Steering unlock unlock command reception status/OK or NG	OK: Steering unlock request is received NG: Steering unlock request is not received	-
      UNLOCK RQ RECEIVE	Steering lock command reception status/OK or NG	OK: Steering lock request is received NG: Steering lock request is not received	-
      EFI COM	SFI communication/OK or NG	OK: SFI communication is normal NG: SFI communication is abnormal	-
      START RQST	ID code box start request condition/OK or NG	OK: Start request condition signal is received (past) NG: Start request condition signal is not received (past)	-
      S CODE CHK-PAST	S code verification result (past)/ OK or NG	OK: Verification is confirmed (past) NG: Verification is not confirmed (past)	-
      L CODE CHK-PAST	L code verification result (past)/ OK or NG	OK: Verification is confirmed (past) NG: Verification is not confirmed (past)	-

   2. Techstream

      Smart Access: 

      TECHSTREAM SMART ACCESS DATA LIST
      
      

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Ignition Switch	Engine switch on (IG) signal/ON or OFF	ON: Engine switch on (ACC, IG) OFF: Engine switch off or on (ACC)	-
      Immobiliser	Engine immobiliser system status/SET or UNSET	SET: Key is not in cabin UNSET: Key is in cabin	-
      Master Key	Master key code signal/MATCH or NO MATCH	MATCH: Master key code is sent NO MATCH: Unmatched master key code is sent	-
      Different Encrypt Code	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      Different Serial Number	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      Frame Error	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      Response	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      BCC Malfunction	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
      Abnormal Status	Transponder chip data/OK or NG	OK: Data OK NG: Data error	-
      ID-BOX Sleep Condition	ID code box condition/YES or NO	YES: ID code box can be sleep condition NO: ID code box cannot be sleep condition	-
      ID-BOX Start Condition	ID code box condition/YES or NO	YES: ID code box sends wake up signal NO: ID code box does not send wake up signal	-
      EFI Code Receive	SFI code receive (when DTC detected) /OK or NG	OK: SFI code is received NG: SFI code is not received	-
      S Code Check	S code verification result/OK or NG	OK: Verification is confirmed NG: Verification is not confirmed	-
      L Code Check	L code verification result/OK or NG	OK: Verification is confirmed NG: Verification is not confirmed	-
      Unlock Request Receive	Steering unlock unlock command reception status/OK or NG	OK: Steering unlock request is received NG: Steering unlock request is not received	-
      Lock Request Receive	Steering lock command reception status/OK or NG	OK: Steering lock request is received NG: Steering lock request is not received	-
      EFI communication	SFI communication/OK or NG	OK: SFI communication is normal NG: SFI communication is abnormal	-
      Engine Start Request	ID code box start request condition/OK or NG	OK: Start request condition signal is received (past) NG: Start request condition signal is not received (past)	-
      S Code Check (Past)	S code verification result (past)/ OK or NG	OK: Verification is confirmed (past) NG: Verification is not confirmed (past)	-
      L Code Check (Past)	L code verification result (past)/ OK or NG	OK: Verification is confirmed (past) NG: Verification is not confirmed (past)	-

HINT:

Using the intelligent tester or Techstream to perform ACTIVE TEST allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing ACTIVE TEST early in troubleshooting is one way to save diagnostic time. DATA LIST information can be displayed while performing ACTIVE TEST.

1. Connect the intelligent tester or Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the tester on.
4. Enter the following menus:
   1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / BODY SYSTEM / SMART ACCESS / ACTIVE TEST.
   2. Techstream - Select: Body Electrical / Smart Access / Active Test.
5. According to the display on tester, perform the "ACTIVE TEST" or "Active Test".
   1. Intelligent tester

      SMART ACCESS: 

      INTELLIGENT TESTER SMART ACCESS ACTIVE TEST
      
      

      Tester Display	Test Part	Control Range
      SECURITY INDIC	Security indicator light (for driver side and front passenger side)	ON or OFF

   2. Techstream

      Smart Access: 

      TECHSTREAM SMART ACCESS ACTIVE TEST
      
      

      Tester Display	Test Part	Control Range
      Security Indicator	Security indicator light (for driver side and front passenger side)	ON or OFF