Roof Headlining: Installation

1. Only when replacing the roof headlining: Install the roof wire.
   NOTE: Securely install the roof No. 1 wire. If there is any slack, noise will occur.

   HINT:

   When removing peeling paper from double-sided tape, do not allow foreign matter to contact the tape's adhesive.

   1. Remove the peeling paper from one side of double-sided tape A.
   2. Attach double-sided tape A to the marks on the roof headlining, as shown in the illustrations below.
   3. Remove the peeling paper from the other side of double-sided tape A.
   4. Align the wire harness to double-sided tape A. Also, align the marking tape areas of the wire harness to the marks on the roof headlining (see A, B and C in the illustrations below). Temporarily attach the wire harness to the roof headlining.
   5. Remove the peeling paper from one side of double-sided tape B. Secure the wire harness to the roof headlining by attaching double-sided tape B to the wire harness and marks on the roof headlining, as shown in A, B and C in the illustrations below.
   6. Align the marking tape area of the wire harness to the roof headlining installation part, as shown in D in the illustrations below. Wrap tape around the wire harness and installation part.
      Fig 1: Identifying Marking Tape Locations On Headlining (W/O Sliding Roof)

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Fig 2: Identifying Marking Tape Locations On Headlining (W/ Sliding Roof)

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Only when replacing the roof headlining:

   Attach the claw of the vanity light assembly to install it.

2. Install the bulb holder to the vanity light.

1. Apply double-sided tape to the pads.
2. Align the pads with the markings on the roof headlining, and then install the pads.
   Fig 3: Identifying Markings On Roof Headlining

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Only when replacing the sliding roof housing: Remove the 11 fasteners from the removed sliding roof housing, and attach them to the roof headlining.

   A: 

   T=0.6 mm (0.023 in.) 

   B: 

   T=2.5 mm (0.098 in.) 

4. Only when replacing the roof headlining: Remove the 11 fasteners from the removed roof headlining, and attach the 11 fasteners to the roof headlining.

   A: 

   T=0.6 mm (0.023 in.) 

   B: 

   T-2.5 mm (0.098 in.) 

   Fig 4: Identifying Fasteners Location On Roof Headlining

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Place the roof headlining into the vehicle through the rear door.
Fig 5: Placing Roof Headlining Through Rear Door
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. w/o Sliding Roof:

   Attach the 2 hooks, fastener, 12 clips labeled B and 4 clips labeled A.

7. w/ Sliding Roof:

   Attach the hook, claw, 11 fasteners, 12 clips labeled B and 4 clips labeled A.

   Fig 6: Identifying Hook And Clip Locations On Sliding Roof

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. w/ Sliding Roof:

   Connect the connector to the driver gear.

9. w/ Sliding Roof:

   Install the roof headlining to the sliding roof housing.

10. Attach the 4 clamps to the front pillar.
11. Connect the roof wire connector to the front pillar.

1. Install the visor with the 2 screws.

1. Install the visor with the 2 screws.

1. Attach the 4 claws to install the cover.

1. Connect the connector.
2. Attach the 2 claws to install the spot light.

1. Connect the connector.
2. Attach the 4 claws to install the room light to the vehicle body.

1. Install the inner rear view mirror (see INSTALLATION ).

1. Connect the connector.
2. Attach the 3 claws and 2 clips, and install the personal light.
3. Install the 2 screws and 2 covers to personal light.

1. Attach the 3 claws and 2 clips, and install the garnish.

1. Attach the 2 claws and 4 clips, and install the garnish.

HINT:

Use the same procedures described for the LH side.

1. Attach the 5 claws and install the garnish.
2. Pull out the folded lip of the weatherstrip.

HINT:

Use the same procedures described for the LH side.

1. Attach the claws to install the garnish.
2. Install the 2 screws.

HINT:

Use the same procedures described for the LH side.

1. Attach the 2 claws and 5 clips to install the garnish.
Fig 7: Identifying Center Pillar Garnish Claws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Attach the 5 claws to install the scuff plate.
2. Pull out the folded lip of the weatherstrip.
Fig 8: Identifying Rear Door Scuff Plate Claws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Attach a new clip A to the vehicle body.
2. Set the pillar garnish to the area labeled B. Using needle-nose pliers, install clip A to the pillar garnish and rotate it 90°.
3. Install the pillar garnish by attaching the claws and clip B.
4. Pull out the folded lip of the weatherstrip.

HINT:

Use the same procedures described for the LH side.

1. Attach the 3 claws to install the trim cover.
2. Pull out the folded lip of the weatherstrip.
   Fig 9: Identifying Front Pillar Garnish Clips - LH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Attach the 5 claws and install the scuff plate.
2. Pull out the folded lip of the weatherstrip.
Fig 10: Identifying Front Door Scuff Plate Claws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Install the console box (see INSTALLATION ).

1. Install the front seat assembly (see INSTALLATION ).

1. w/o Seat Position Memory System:

   Inspect the front power seat assembly (see ON-VEHICLE INSPECTION ).

   w/ Seat Position Memory System:

   Inspect the front power seat assembly (see ON-VEHICLE INSPECTION ).

1. Inspect the function of the seat belt (see ON-VEHICLE INSPECTION ).

1. Inspect the seat heater (see OPERATION CHECK ).

1. Perform initialization (see INITIALIZATION ).
   NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.