FixVault
Home › Lexus › 2008 › IS 250 AWD › Repair and Diagnosis › Restraints › Air Bag, SRS › Pre-Collision › Pre-Collision System › Data List / Active Test

Data List / Active Test

  1. READ DATA LIST 

    HINT:

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Pre-Collision / Data List.
    5. Read the Data List according to the display on the Techstream.

    Pre-Collision: 

    DATA LIST AND PRE-COLLISION

    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    Driver Buckle SW Buckle switch status of driver's seat/
    UNSET: Unfasten driver side seat belt
    SET: Fasten driver side seat belt
    NG: Indeterminate data    		 UNSET/SET -
    Passenger Buckle SW Buckle switch status of passenger's seat /
    UNSET: Unfasten passenger side seat belt
    SET: Fasten passenger side seat belt
    NG: Indeterminate data    		 UNSET/SET -
    Drive Belt Control Seat belt control status of driver's seat/
    STOP: Control stopped
    ON: Controlled
    ERROR: Indeterminate data    		 STOP/ON Seat belt (driver side) is fastened
    Passenger Belt Control Seat belt control status of passenger's seat /
    STOP: Control stopped
    ON: Controlled
    ERROR: Indeterminate data    		 STOP/ ON Seat belt (passenger side) is fastened
    Number of Present DTC Number of present trouble codes / min: 0, max: 255 Number of DTCs will be displayed -
    Number of Past DTC Number of past trouble codes / min: 0, max: 255 Number of DTCs will be displayed -
  2. PERFORM ACTIVE TEST 

    HINT:

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Pre-Collision / Active Test.
    5. Perform Active Test according to the display on the Techstream.

    HINT:

    The engine switch must be turned on to proceed with the Active Test using the Techstream.

    Pre-Collision: 

    DATA LIST AND PRE-COLLISION

    Tester Display Test Part Control Range Diagnostic Note
    Driver Seat Belt Motor Driver's seat belt motor ON: Seat belt motor operates
    OFF: Seat belt motor does not operate    		 Seat belt (driver side) is fastened
    Passenger Seat Belt Motor Passenger's seat belt motor ON: Seat belt motor operates
    OFF: Seat belt motor does not operate    		 Seat belt (passenger side) is fastened
    Drive and Passenger Seat Belt Motor Driver's and passenger's seat belt motor ON: Seat belt motors operate
    OFF: Seat belt motors do not operate    		 Seat belts (driver and passenger) are fastened
    NOTE:
    • The belt motor is not equipped with buckle switch is not operated.
    • The protect heating up of belt motor, this test can not be activated continuously. Please operate with 30 seconds interval.
About FixVault