FixVault
Home › Lexus › 2008 › IS 350 › Repair and Diagnosis › Electrical › Gauges › Meter › Meter / Gauge System › Customize Parameters

Customize Parameters

  1. Meter/Gauge System 
    1. Combination Meter Assembly
      NOTE: Be sure to record the current value before customizing.

      HINT:

      The following items can be customized using the Techstream.

      Combination Meter: 

      TESTER DISPLAY REFERENCE

      Tester Display Default Contents Setting
      Key Remind Volume Large Function to change the volume of the key remind warning buzzer Large, Medium, SmallL
      Key Remind Sound Normal Function to change the cycle of the key remind warning buzzer Fast, Normal, Slow
      Units By Region ML/G ((1)) KM/L ((2)) Function to change the unit of the trip information display ML/G, ML/G, KM/L
      (1) U.S.A.
      (2) for Canada

      HINT:

      The following items can be customized without using the Techstream.

      TECHSTREAM REFERENCE

      Item Default Contents Setting
      Seat belt warning buzzer (See procedure "A") b-on Function to change volume of key remind warning buzzer b-on, b-oFF
      Speed indicator (See procedure "B") 75 (mph) ((1)) 120 (km/h) ((2)) Function to change the value that decides the speed indicator when to illuminate 30 to 100 (mph)((1)), 50 to 160 (km/h) ((2))
      Tach indicator (See procedure B) 5,000 (rpm) Function to change the value that decides the tach indicator when to illuminate 2,000 to 6,500 (rpm)
      (1) U.S.A.
      (2) for Canada
    2. Seat Belt Buzzer ON/OFF setting (Procedure "A") The buzzer ON/OFF setting, which is a setting of the buzzer function of the combination meter, can disable the driver and front passenger side seat belt buzzers.
      NOTE:
      • These buzzers should be on for safe driving. Perform these procedures only if it is necessary to set the buzzer off (disabled).
      • When either the battery cable or the combination meter connector is disconnected, these buzzers are set on (enabled).
      • Odometer returns to 0 after starting this procedure, although it is not displayed.

      HINT:

      "b-oFF" indicates that the buzzer is OFF. "b-on" indicates that the buzzer is ON. The buzzer ON/ OFF setting will be finished (the odometer will display "ODO") if the ODO/TRIP switch is not operated for 10 seconds or more. In this case, perform step  11 to check that the buzzer ON/OFF setting is complete. If it is not complete, start from step  1 again.

      1. Driver and front passenger side seat belt buzzers
        1. Engine switch on (IG).
        2. Press the ODO/TRIP switch until the odometer displays "ODO".
        3. Engine switch off.
        4. Engine switch on (IG).
        5. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
        6. Continue holding down the ODO/TRIP switch and fasten the driver side seat belt.
        7. Check that the odometer displays either "b-on" or "b-oFF".
        8. Press the ODO/TRIP switch to change the display to "b-oFF".
        9. Engine switch off.
        10. Engine switch on (IG).
        11. Check that no buzzer sounds.
      2. Front passenger side seat belt buzzer
        1. Engine switch on (IG).
        2. Press the ODO/TRIP switch until the odometer displays "ODO".
        3. Engine switch off.
        4. Engine switch on (IG).
        5. Sit in the front passenger seat. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
        6. Sit in the front passenger seat. Continue holding down the ODO/TRIP switch and fasten the front passenger side seat belt.
        7. Check that the odometer displays either "b-on" or "b-oFF".
        8. Press the ODO/TRIP switch to change the display to "b-oFF".
        9. Engine switch off.
        10. Engine switch on (IG).
        11. Check that no buzzer sounds.
    3. SPEED AND TACH INDICATOR (Procedure "B")
      1. Select the SPEED INDICATOR or TACH INDICATOR using the satellite switch (RH, ON/ OFF, or LH switch).
      2. Turn the SPEED INDICATOR or TACH INDICATOR function off by using the ON/OFF switch.
      3. Turn the SPEED INDICATOR or TACH INDICATOR function on again by using the ON/OFF switch.
        Fig 1: Display - Satellite Switch And Operation
        G05320776Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Leave the display on for 1 second to allow it to change to the SET display.
      5. When SET flashes, the speedometer needle moves to indicate the previously set vehicle speed and then stops.
        Fig 2: Display - Speed Indicator And Tacho Indicator
        G05320779Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      6. Push the LH or RH switch within 6 seconds of the speedometer needle moving in order to allow setting of the speedometer indicator set point.
        • The speedometer needle moves by 1 degree each time the LH or RH switch is pushed.
        • Pushing and holding the switch changes values at a faster rate.
          Fig 3: Display - ON/OFF Switch And Speedometer Indicator
          G05320780Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      7. When the ON/OFF switch is pushed, the speedometer or tachometer needle stays at the setting value for 1 second, the buzzer sounds once, and the SPEED indicator illuminates only momentarily one time in yellow.
About FixVault