FixVault
Home › Lexus › 2008 › IS F › Repair and Diagnosis › Restraints › Air Bag, SRS › Pre-Collision › Pre-Collision System › Data List / Active Test

Data List / Active Test

  1. DATA LIST 

    HINT.

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Connect the Techstream to the DLC3
    2. Turn the engine switch on (IG)
    3. Turn the Techstream on.
    4. Enter the following menus. Body Electrical / Pre-Collision / Data List.
    5. Read the Data List according to the display on the Techstream

      Pre-Collision 

      DATA LIST - PRE-COLLISION

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Driver Buckle SW Buckle switch status of driver side seat/
      UNSET Unfasten driver side seat belt
      SET Fasten driver side seat belt
      NG Indeterminate data      		 UNSET/SET -
      Passenger Buckle SW Buckle switch status of passenger side seat/
      UNSET Unfasten passenger side seat belt
      SET Fasten passenger side seat belt
      NG Indeterminate data      		 UNSET/SET -
      Drive Belt Control Seat belt control status of driver side seat/
      STOP Control stopped
      ON Controlled
      ERROR Indeterminate data      		 STOP/ON Seat belt (driver side) is fastened
      Passenger Belt Control Seat belt control status of passenger side seat/
      STOP Control stopped
      ON Controlled
      ERROR Indeterminate data      		 STOP/ ON Seat belt (passenger side) is fastened
      Number of Present DTC Number of present trouble codes/
      min 0, max 255      		 Number of DTC s will be displayed -
      Number of Past DTC Number of past trouble codes/
      min 0, max 255      		 Number of DTC s will be displayed -
  2. ACTIVE TEST 

    HINT.

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time Data List information can be displayed while performing Active Tests

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on
    4. Enter the following menus. Body Electrical / Pre-Collision / Active Test
    5. Perform Active Test according to the display on the Techstream.

      HINT.

      The engine switch must be turned on to proceed with the Active Test using the Techstream

      Pre-Collision 

      ACTIVE TEST - PRE-COLLISION

      Tester Display Test Part Control Range Diagnostic Note
      Driver Seat Belt Motor Driver seat belt motor ON Seat belt motor operates
      OFF Seat belt motor does not operate      		 Seat belt (driver side) is fastened
      Passenger Seat Belt Motor Passenger seat belt motor ON Seat belt motor operates
      OFF Seat belt motor does not operate      		 Seat belt (passenger side) is fastened
      Driver and Passenger Seat Belt Motor Driver and passenger seat belt motors ON Seat belt motors operate
      OFF Seat belt motors do not operate      		 Seat belts (driver and passenger sides) are fastened
      NOTE:
      • The seat belts not equipped with a buckle switch cannot be operated.
      • To prevent overheating the belt motor, this test cannot be activated repeatedly. Operate it using at least 30 seconds interval.
About FixVault