Inspection Procedure

1. Check that the entry lock and unlock function can be operated at each door.

   Result 

   RESULT REFERENCE
   
   

   Result	Proceed to
   Entry function can be performed	A
   Entry function cannot be performed	B

B: GO TO DTC OF OTHER COMPONENTS (PROCEED TO PROBLEM SYMPTOM FLOWCHART FOR EACH DOOR)  (See PROBLEM SYMPTOMS TABLE  )

A: Go to next step 

1. When the luggage compartment door opener switch is operated, check that the luggage compartment door opens.

   Result 

   RESULT REFERENCE
   
   

   Result	Proceed to
   Luggage compartment door opens (w/o power trunk opener and closer system)	A
   Luggage compartment door does not open (w/o power trunk opener and closer system)	B
   Luggage compartment door opens (w/ power trunk opener and closer system)	C
   Luggage compartment door does not open (w/ power trunk opener and closer system)	D

B: GO TO LUGGAGE COMPARTMENT DOOR OPENER SYSTEM  (See INSPECTION PROCEDURE )

C: Go to step  11

D: GO TO POWER TRUNK LID SYSTEM  (See INSPECTION PROCEDURE )

A: Go to next step 

1. Using the Techstream, read the Data List.

   Body No.4 (Rear room junction block ECU) 

   MEASUREMENT ITEM/DISPLAY CHART
   
   

   Tester Display	Measurement Item/Display	Normal Condition	Diagnostic Note
   Luggage Push Switch	Luggage compartment door opener switch / ON or OFF	ON: Luggage compartment door opener switch is pushed OFF: Luggage compartment door opener switch is not pushed	-

   OK: On the screen, item changes between ON and OFF according to above chart. 

NG: Go to step  9

OK: Go to next step 

1. Bring the electrical key transmitter near the electrical key antenna (in rear bumper), and perform an entry luggage compartment open function check.
   NOTE: If the key is brought within 0.2 m (0.6 ft) of the rear bumper, communication is not possible.

   HINT:

   • When the electrical key transmitter is brought near the electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
   • If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
     Fig 1: Identifying Distance Between Key And Rear Bumper 0.3 m (0.9 ft.)

     Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Result 

   RESULT REFERENCE
   
   

   Result	Proceed to
   Operation check fails	A
   Operation check is normal	B

B: AFFECTED BY WAVE INTERFERENCE 

A: Go to next step 

1. Diagnostic mode inspection (rear inside oscillator)
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Access / Smart Communication Check /Overhead + Luggage.
   5. When the electrical key transmitter is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.
      Fig 2: Identifying Distance Between Key And Rear Bumper 0.7 To 1.0 m (2.3 To 3.3 ft.)

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

      OK: Wireless door lock buzzer sounds 

NG: Go to step 6 

OK: REPLACE CERTIFICATION ECU 

Fig 3: Identifying R40 Antenna Connector And L15 ECU Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the R40 antenna connector.
2. Disconnect the L15 ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   STANDARD RESISTANCE
   
   

   Tester Connection	Condition	Specified Condition
   L15-31 (CLG8) - R40-1 (CLG5)	Always	Below 1 Ω
   L15-32 (CG8B) - R40-2 (CLGB)	Always	Below 1 Ω
   L15-31 (CLG8) - Body ground	Always	10 kΩ or higher
   L15-32 (CG8B) - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Replace the electrical key antenna with a new one or normally functioning one (see REMOVAL  ).
2. Check that the entry luggage compartment open function operates normally.

   OK: Operates normally 

NG: Go to step 8 

OK: Go to next step 

1. Replace the luggage junction block ECU with a new one or normally functioning one.
2. Check that the entry luggage compartment open function operates normally.

   OK: Operates normally 

NG: REPLACE CERTIFICATION ECU 

OK: END (JUNCTION BLOCK ECU IS DEFECTIVE) 

1. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   STANDARD RESISTANCE
   
   

   Tester Connection	Switch Condition	Specified Condition
   1 - 2	OFF	Below 1 Ω
   1 - 2	ON	10 kΩ or higher

   Fig 4: Inspecting Luggage Compartment Door Opener Switch

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPLACE LUGGAGE COMPARTMENT DOOR OPENER SWITCH  (See LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH )

OK: Go to next step 

Fig 5: Identifying S38 Switch Connector And S63 ECU Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the S38 switch connector.
2. Disconnect the S63 ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   STANDARD RESISTANCE
   
   

   Tester Connection	Condition	Specified Condition
   S38-1 - Body ground	Always	Below 1 Ω
   S38-2 - S63-6 (LPSW)	Always	Below 1 Ω
   S38-2 - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: REPLACE LUGGAGE ROOM JUNCTION BLOCK (REAR JUNCTION BLOCK ECU) 

1. Using the Techstream, read the Data List.

   Back Door (Luggage closer motor assembly) 

   MEASUREMENT ITEM/DISPLAY CHART
   
   

   Tester Display	Measurement Item/Display	Normal Condition	Diagnostic Note
   Back Door Handle SW	Luggage compartment door opener switch / ON or OFF	ON: Luggage compartment door opener switch is pushed OFF: Luggage compartment door opener switch is not pushed	-

   HINT:

   For vehicles with the power trunk opener and closer system, the Data List of the power trunk opener and closer ECU can be used to check the luggage compartment door opener switch information. For vehicles without the power trunk opener and closer system, the Data List of the luggage room junction block ECU can be used to check the luggage compartment door opener switch information.

   OK: On the screen, item changes between ON and OFF according to above chart. 

NG: Go to step  17

OK: Go to next step 

1. Bring the electrical key transmitter near the electrical key antenna (in rear bumper), and perform an entry luggage compartment open function check.
   NOTE: If the key is brought within 0.2 m (0.6 ft.) of the rear bumper, communication is not possible.

   HINT:

   • When the electrical key transmitter is brought near the electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
   • If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
     Fig 6: Identifying Distance Between Key And Rear Bumper 0.3 m (0.9 ft.)

     Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Result 

   RESULT REFERENCE
   
   

   Result	Proceed to
   Operation check fails	A
   Operation check is normal	B

B: REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY  (See INSTALLATION )

A: Go to next step 

1. Diagnostic mode inspection (rear inside oscillator)
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Access / Smart Communication Check /Overhead + Luggage.
   5. When the electrical key transmitter is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.
      Fig 7: Identifying Distance Between Key And Rear Bumper 0.7 To 1.0 m (2.3 To 3.3 ft.)

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

      OK: Wireless door lock buzzer sounds 

NG: Go to step 14 

OK: REPLACE CERTIFICATION ECU 

Fig 8: Identifying R40 Antenna Connector And L15 ECU Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the R40 antenna connector.
2. Disconnect the L15 ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   STANDARD RESISTANCE
   
   

   Tester Connection	Condition	Specified Condition
   L15-31 (CLG8) - R40-1 (CLG5)	Always	Below 1 Ω
   L15-32 (CG8B) - R40-2 (CLGB)	Always	Below 1 Ω
   L15-31 (CLG8) - Body ground	Always	10 kΩ or higher
   L15-32 (CG8B) - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Replace the electrical key antenna with a new one or normally functioning one (see REMOVAL  ).
2. Check that the entry luggage compartment open function operates normally.

   OK: Operates normally 

NG: Go to step 16 

OK: END (ELECTRICAL KEY ANTENNA IS DEFECTIVE) 

1. Replace the luggage closer motor with a new one or normally functioning one (see TRUNK LID ACTUATOR ).
2. Check that the entry luggage compartment open function operates normally.

   OK: Operates normally 

NG: REPLACE CERTIFICATION ECU 

OK: END (LUGGAGE CLOSER MOTOR IS DEFECTIVE) 

1. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   STANDARD RESISTANCE
   
   

   Tester Connection	Switch Condition	Specified Condition
   1 - 2	OFF	Below 1 Ω
   1 - 2	ON	10 kΩ or higher

   Fig 9: Identifying S38 Switch Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPLACE LUGGAGE COMPARTMENT DOOR OPENER SWITCH  (See LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH )

OK: Go to next step 

Fig 10: Identifying S38 Switch Connector And S43 ECU Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the S38 switch connector.
2. Disconnect the S43 ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   STANDARD RESISTANCE
   
   

   Tester Connection	Condition	Specified Condition
   S38-1 - Body ground	Always	Below 1 Ω
   S38-2 - S43-19 (LPSW)	Always	Below 1 Ω
   S38-2 - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY  (See INSTALLATION )