FixVault
Home › Lexus › 2008 › LS 460L › Repair and Diagnosis › Body & Frame › Door Locks › Door Lock › Smart Access System With Push-Button Start › Rear Door RH Entry Lock and Unlock Functions do not Operate › Inspection Procedure

Inspection Procedure

  1. CHECK POWER DOOR LOCK OPERATION 
    1. When the master switch assembly's door control switch is operated, check that the locked doors unlock.

      Result 

      RESULT REFERENCE

      Result Proceed to
      Door locks operate normally OK
      Door locks do not operate normally NG

    NG: GO TO POWER DOOR LOCK CONTROL SYSTEM 

    OK: Go to next step 

  2. READ VALUE OF TECHSTREAM 
    1. Using the Techstream, read the Data List.

      Rear Right Door (Rear door ECU RH) 

      MEASUREMENT ITEM/DISPLAY CHART

      Tester Display Measurement Item/Display Normal Condition
      Entry Sensor Rear RH side door touch sensor / ON or OFF ON: Rear RH side door sensor is touched
      OFF: Rear RH side door sensor is not touched
      Outside Handle Trigger SW Rear RH side door outside handle lock switch / ON or OFF ON: Rear RH side door outside handle lock switch is pushed
      OFF: Rear RH side door outside handle lock switch is not pushed

      Result 

      RESULT REFERENCE

      Result Proceed to
      Display does not change according to manual operation A
      Display changes according to manual operation B

    B: Go to step  9

    A: Go to next step 

  3. CHECK REAR DOOR ECU RH 
    Fig 1: Identifying O3 ECU Connector Terminals
    G04951673Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Measure the voltage according to the value(s) in the table below.

      Standard voltage 

      STANDARD VOLTAGE

      Tester Connection Condition Specified Condition
      O3-12 (OSCB) - O3-15 (OSCE) Always 11 to 14 V

    NG: REPLACE REAR DOOR ECU RH  (See INSTALLATION )

    OK: Go to next step 

  4. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR ECU RH) 
    Fig 2: Identifying c2 Oscillator Connector And O3 ECU Connector Terminals
    G05783212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the c2 oscillator connector.
    2. Disconnect the O3 ECU connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      STANDARD RESISTANCE

      Tester Connection Condition Specified Condition
      c2-1 (B) - O3-12 (OSCB) Always Below 1 Ω
      C2-6 (SENS) - O3-14 (SENS) Always Below 1 Ω
      c2-7 (GND) - O3-15 (OSCE) Always Below 1 Ω
      c2-1 (B) - Body ground Always 10 kΩ or higher
      c2-6 (SENS) - Body ground Always 10 kΩ or higher
      c2-7 (GND) - Body ground Always 10 kΩ or higher

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  5. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE RH) 
    Fig 3: Identifying c1 Handle Connector And c2 Oscillator Connector Terminals
    G04951675Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the c1 handle connector.
    2. Disconnect the c2 oscillator connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      STANDARD RESISTANCE

      Tester Connection Condition Specified Condition
      c2-2 (SGT6) - c1-6 (SGT5) Always Below 1 Ω
      c2-9 (TRG-) - c1-1 (TRG-) Always Below 1 Ω
      c2-2 (SGT6) - Body ground Always 10 kΩ or higher
      c2-9 (TRG-) - Body ground Always 10 kΩ or higher

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  6. CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - REAR DOOR OUTSIDE HANDLE RH) 
    Fig 4: Identifying c1 Handle Connector And O3 ECU Connector Terminals
    G05852839Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the c1 handle connector.
    2. Disconnect the O3 ECU connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      STANDARD RESISTANCE

      Tester Connection Condition Specified Condition
      c1-3 (TRG+) - O3-20 (TRG+) Always Below 1 Ω
      c1-3 (TRG+) - Body ground Always 10 kΩ or higher

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) 
    1. Replace the door electrical key oscillator with a new one or normally functioning one (see INSTALLATION ).
    2. Check that the entry function operates normally.

      OK: Operates normally 

    NG: Go to step 8 

    OK: END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE) 

  8. CHECK REAR DOOR OUTSIDE HANDLE RH (OPERATION) 
    1. Replace the rear door outside handle RH with a new one or normally functioning one (see REMOVAL  ).
    2. Check that the entry function operates normally.

      OK: Operates normally 

    NG: REPLACE REAR DOOR ECU RH  (See INSTALLATION )

    OK: END (REAR DOOR OUTSIDE HANDLE RH IS DEFECTIVE) 

  9. CHECK WAVE ENVIRONMENT 
    1. Bring the electrical key transmitter near the rear right door outside handle, and perform a rear right door entry lock and unlock operation check.
      NOTE: If the key is brought within 0.2 m (0.6 ft.) of the door handle, communication is not possible.
      Fig 5: Identifying Distance Between Key And Door Handle 0.3 m (0.9 ft.)
      G04951627Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      • When the electrical key transmitter is brought near the rear right passenger door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
      • If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      Result 

      RESULT REFERENCE

      Result Proceed to
      Operation check fails A
      Operation check is normal B

    B: AFFECTED BY WAVE INTERFERENCE 

    A: Go to next step 

  10. KEY DIAGNOSTIC MODE 
    1. Diagnostic mode inspection (rear door RH outside oscillator)
      1. Connect the Techstream to the DLC3.
      2. Turn the engine switch on (IG).
      3. Turn the Techstream on.
      4. Enter the following menus: Body Electrical/ Smart Access / Smart Communication Check /Overhead + Driver Side Rear.
      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
        Fig 6: Identifying Distance Between Key And Door Handle 0.7 To 1.0 m (2.3 To 3.3 ft.)
        G04951632Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        HINT:

        If the buzzer sounds, it can be determined that the rear right seat outside transmitter is operating normally.

        OK: Wireless door lock buzzer sounds 

    NG: Go to step 11 

    OK: END (CERTIFICATION ECU IS DEFECTIVE) 

  11. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR CERTIFICATION ECU) 
    Fig 7: Identifying c2 Oscillator Connector And L16 ECU Connector Terminals
    G04951679Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the c2 oscillator connector.
    2. Disconnect the L16 ECU connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      STANDARD RESISTANCE

      Tester Connection Condition Specified Condition
      c2-5 (CLGB) - L16-11 (CG4B) Always Below 1 Ω
      C2-10 (CLG) - L16-10 (CLG4) Always Below 1 Ω
      c2-5 (CLGB) - Body ground Always 10 kΩ or higher
      C2-10 (CLG) - Body ground Always 10 kΩ or higher

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  12. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR ECU RH) 
    Fig 8: Identifying c2 Oscillator Connector And O3 ECU Connector Terminals
    G04951642Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the c2 oscillator connector.
    2. Disconnect the O3 ECU connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      STANDARD RESISTANCE

      Tester Connection Condition Specified Condition
      c2-4 (SEL) - O3-16 (SEL) Always Below 1 Ω
      c2-4 (SEL) - Body ground Always 10 kΩ or higher

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  13. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE RH) 
    Fig 9: Identifying c1 Handle Connector And c2 Oscillator Connector Terminals
    G04951681Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the c1 handle connector.
    2. Disconnect the c2 oscillator connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      STANDARD RESISTANCE

      Tester Connection Condition Specified Condition
      c2-3 (ANT5) - c1-5 (ANT5) Always Below 1 Ω
      c2-8 (ANT6) - c1-2 (ANT6) Always Below 1 Ω
      c2-3 (ANT5) - Body ground Always 10 kΩ or higher
      C2-8 (ANT6) - Body ground Always 10 kΩ or higher

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  14. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) 
    1. Replace the door electrical key oscillator with a new one or normally functioning one (see INSTALLATION ).
    2. Check that the entry function operates normally.

      OK: Operates normally 

    NG: Go to step 15 

    OK: END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE) 

  15. CHECK REAR DOOR OUTSIDE HANDLE RH (OPERATION) 
    1. Replace the rear door outside handle RH with a new one or normally functioning one (see REMOVAL  ).
    2. Check that the entry function operates normally.

      OK: Operates normally 

    NG: Go to step 16 

    OK: END (REAR DOOR OUTSIDE HANDLE RH IS DEFECTIVE) 

  16. CHECK REAR DOOR ECU RH (OPERATION) 
    1. Replace the rear door ECU RH with a new one or normally functioning one (see INSTALLATION ).
    2. Check that the entry function operates normally.

      OK: Operates normally 

    NG: REPLACE CERTIFICATION ECU 

    OK: END (REAR DOOR ECU RH IS DEFECTIVE) 

About FixVault