Front Stabilizer Bar: Installation

HINT:

A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE FOR STANDARD BOLTS ).

1. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH 
   1. Install the front suspension member reinforcement LH to the vehicle with the 4 bolts.

      Torque: 50 N*m (510 kgf*cm, 37 ft.*lbf) 

      Fig 1: Locating Bolts And Front Suspension Member Reinforcement LH

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH 

   HINT:

   Install the RH side following the same procedures as the LH side.

3. INSTALL FRONT NO. 1 STABILIZER BAR BUSH 
   1. Install the 2 front No. 1 stabilizer bar bushes outside of the bush stoppers on the front stabilizer bar as shown in the illustration.
      NOTE: Be sure to install the front No. 1 stabilizer bar bushes so that the cutouts face the front of the vehicle.
      Fig 2: Identifying Bush Stopper

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. TEMPORARILY TIGHTEN FRONT STABILIZER BAR 
   1. Temporarily install the front stabilizer bar with the 4 bolts and the front No. 1 stabilizer bracket LH and RH.
      NOTE: Install the front stabilizer bar so that the identification mark face vehicle right side.
      Fig 3: Identifying Front Stabilizer Bar Identification Mark

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. TIGHTEN FRONT NO. 1 STABILIZER BRACKET LH 
   1. Tighten the front No. 1 stabilizer bracket LH with the 2 bolts.

      Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf) 

      Fig 4: Locating Bolts And Front No. 1 Stabilizer Bracket LH

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. TIGHTEN FRONT NO. 1 STABILIZER BRACKET RH 

   HINT:

   Install the RH side following the same procedures as the LH side.

7. INSTALL ENGINE UNDER COVER REAR LH 
   1. Install the engine under cover rear LH with the 2 screws.
   Fig 5: Locating Screws And Engine Under Cover Rear LH
   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. INSTALL ENGINE UNDER COVER REAR RH 

   HINT:

   Install the RH side following the same procedures as the LH side.

9. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY LH 
   1. Install the engine under cover sub-assembly LH with the 2 screws.
   Fig 6: Locating Screws And Engine Under Cover Sub-Assembly LH
   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY RH 

    HINT:

    Install the RH side following the same procedures as the LH side.

11. INSTALL FRONT STABILIZER LINK ASSEMBLY LH 
    1. Install the front stabilizer link with the 2 nuts.

       Torque: 84 N*m (857 kgf*cm, 62 ft.*lbf) 

       HINT:

       If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.

       Fig 7: Locating Nuts And Front Stabilizer Link Assembly LH

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
12. INSTALL FRONT STABILIZER LINK ASSEMBLY RH 

    HINT:

    Install the RH side following the same procedures as the LH side.

13. INSTALL NO. 2 ENGINE UNDER COVER 
    1. Install the No. 2 engine under cover with the 8 bolts.

       Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) (for bolt A) 

       27 N*m (275 kgf*cm, 20 ft.*lbf) (for bolt B) 

       Fig 8: Locating No. 2 Engine Under Cover And Bolts

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
14. INSTALL FRONT WHEEL 
15. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT  (See INSTALLATION  )
16. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT  (See ADJUSTMENT )
17. PREPARATION FOR HEADLIGHT AIMING (Using a screen)  (See ADJUSTMENT )
18. HEADLIGHT AIMING INSPECTION  (See ADJUSTMENT )
19. HEADLIGHT AIMING ADJUSTMENT  (See REASSEMBLY )
20. ADJUST OBJECT RECOGNITION CAMERA 
    1. Adjust the object recognition camera (see ADJUSTMENT ).